pro user DRC7010 User manual
* Optional: Extendable with second camera / Erweiterbar um eine zweite Kamera / Uitbreidbaar
met tweede camera / Extensible a deux cameras. Model: DRC-CAM Article Number 20128
DIGITAL WIRELESS BACKUP CAMERA
SYSTEM
DIGITALES KABELLOSES RÜCKFAHR-
KAMERA-SYSTEM
SYSTEME DE CAMERA DE RECUL SANS FIL
NUMERIQUE
DIGITALE DRAADLOOS CAMERASYSTEEM
with 17,8cm / 7” monitor
mit 17,8cm / 7” Monitor
avec écran 17,8cm / 7”
met 17,8cm / 7” monitor
DRC7010
*
2
INTRODUCTION
The Pro-User DRC7010 is a member of the family of advanced car backup systems
manufactured by Pro-User International Ltd. The Pro-User Digital Backup Camera and
Monitor with built in transmitter box will improve your ability to see behind your car,
camper or trailer. We have taken numerous measures in quality control to ensure that
your product arrives in top condition and will perform to your satisfaction.
For optimal performance and safety, please read the following instructions
carefully !
IMPORTANT SAFETY INSTRUCTIONS
If you are not confident working with 12V/24V DC vehicle wiring, removing and
reinstalling interior panels, carpeting, dashboards or other components of your vehicle,
contact the vehicle’s manufacturer, or consider having the camera system professionally
installed.
Interference
By using a digital transmission system, this device is free from interferences coming from
Bluetooth®, cell phones, Wi-Fi routers, power lines and other various electrical equipment.
Maintenance
The camera system is maintenance-free and must not be opened. Any attempt at
modification or repair by the user will entail the loss of your guarantee.
PARTS
1. Monitor and dashboard stand 2. Camera with mounting plate
3. Mounting Accessories 4. Monitor Power Cable
5. Mounting strap (2x) 6. Mounting Plate
and adhesive tape
. Monitor Power Cable
3
INSTALLATION
These instructions are only meant as a general guide due to the number of
different makes & models. For vehicle specific questions contact your vehicle’s
manufacturer.
Camera installation
The camera can be tilted vertically to adjust the viewing angle.Make sure that its field of
view is not obstructed. There are several ways to mount the camera on the back of your
car. But the most convenient is to mount it near the license plate. Supplied is a mounting
plate that can be fixed behind the license plate. The camera itself can fixed on this
mounting plate.
Please note: At some vehicles it may not be possible to mount the camera near the
license plate. You may have to find another spot at the back of your car to mount it.
1. Remove the rear license plate, and then loosen the license plate´s bolts/screws.
2. Position the supplied mounting plate (together with the camera) behind the license
plate bracket. Secure both license plate bracket and mounting plate with the license
plate bracket bolts/screws.
4
3. Reinsert the license plate on the license plate bracket.
4. Choose a routing path for the camera’s power cable through the vehicle’s body to the
backup light circuit.
5. Some vehicles may have a hole available to pass the wire through the trunk, such as
where the license plate light is mounted. Otherwise you probably could drill a hole
close to where the power cable is attached to the camera. Once you have chosen
where the cable will enter the vehicle’s body, remove the camera. If you are able to
use an existing opening, skip the next two steps.
6. Remove the license plate and camera before drilling. ATTENTION: Before drilling
any hole, remove the camera and the licence plate and carefully examine the
area around and behind the installation position. Make sure that there are no
parts that can be damaged (especially electrical cables, components of the
vehicle´s fuel system or any liquid tanks). Please take every reasonable
precaution. Choose a drill that is suitable for the supplied grommet and
material.
7. After drilling the hole, insert the supplied grommet and pass the camera cables
through the grommet into the vehicle.
8. Next you’ll need to find the vehicle’s backup lights. Turn the vehicle’s ignition key to
the accessory position, engage the parking brake and go into reverse. Look at the
vehicle’s tail lights to see where the reverse lights are located (usually the white
lights). To locate the backup light’s 12V/24V (+) wire, it probably will be necessary to
gain access to the rear of the vehicle’s taillight. For help locating the vehicle’s reverse
light circuit contact your vehicle’s manufacturer for vehicle specific wiring diagrams.
9. Once you have located the reverse light circuit you will have to route the camera
cable to that location. Securely fasten the power cable to prevent it from being
caught on any vehicle component such as the trunk hinge. Never route the cable on
the outside of the vehicle!
10. The reverse light sockets on most
vehicles have two wires connected to
them. Usually the negative wire is
black and the positive wire is a colored
wire. If you are uncertain about the
wiring, you can use a 12V/24V
multimeter available at most auto
parts stores, to determine which is the
positive wire. Follow the
manufacturer’s instructions for the
safe use of the multimeter.
11. After determining which wire is the positive and which is the negative, turn off the
ignition key and remove the battery’s negative cable (ground -).
5
12. Connect the camera´s red wire using the supplied in-line wire connectors to the
reverse light’s positive (+) wire. Use a set of slip joint pliers to squeeze them and
insure a good connection.
13. Connect the black wire of the camera´s power cable to the reverse light’s negative (-)
wire or ground.
14. Reinstall the reverse light bulb and the light socket. Secure all the wires with cable
ties or electrical tape.
15. Re-attach the negative battery cable to the battery.
Monitor Installation
When choosing a location for the monitor, make sure the monitor is mounted in
an area that will not obstruct your vision while driving.
The DRC7010 can be fixed in your vehicle in several ways. The monitor can be placed on
your (A) dashboard via the dashboard stand or (B) fixed via the supplied straps on you
visor or a headrest.
A. Dashboard stand *
1. Before mounting the monitor, clean all adherends well. Put one
side of the double-faced adhesive tape on the bottom of the
dashboard stand.
2. Position the stand onto the dashboard
3. Press the stand against the dashboard surface to fix the
location.
4. Snap in the monitor to the stand´s mounting arm.
5. Adjust the mounting arm to suit your viewing angle to the
monitor.
6. In order to remove the monitor, press the arrow sign on the mounting arm to release.
6
* to maximize the bond strength of the adhesive, it is recommended to applicate the
tape under the following conditions:
•All surfaces must be clean, dry, dust and grease free.
•The adherents temperature should be between 21 and 38 degrees Celsius. Don´t
applicate below 10 degrees or under direct sunlight.
•If possible, choose a mounting position where no direct sunlight can heat up the
dashboard stand.
B. Visor and Headrest Mount
1. Use the supplied two straps and pull them through the recesses at the back of the
monitor unit.
2. Position the monitor on the visor or headrest.
3. Pull the straps across the visor or headrest.
4. Fasten the straps.
Monitor 12/24V connection
1. Route the supplied power cable to the vehicle’s cigarette
lighter socket/12V power outlet. The cable routing must not
interfere with the safe operation of the vehicle.
2. Insert the small DC plug of the power cable into the side of the
monitor.
3. Plug in the 12/24 Volt cigarette lighter plug into the vehicle’s
cigarette lighter socket.
Testing the System
1. Check if the vehicle’s negative battery cable (ground) has been reattached.
2. Turn the ignition key to the accessory position - do not start the vehicle.
3. Engage the parking brake, and put the vehicle´s shifter in the reverse position. The
System should activate itself. If not, press the Power-button on the Monitor.
4. If not already done: Please pair your camera(s) to the monitor (as described in
chapter OPERATION)
5. After testing (and re-adjusting if needed) the unit, all cabling should be installed
permanently: Route all wires behind interior panels or under carpeting. Use the
supplied cable ties to keep excess wires neat and compact.
NOTE: UNDER EXTREME BRIGHT LIGHT CONDITIONS, THE SCREEN IMAGE MAY
TAKE A FEW SECONDS TO STABILIZE. PLEASE WAIT UNTIL THE IMAGE HAS
STABILIZED BEFORE BACKING UP.
7
OPERATION
Before the 1st operation: Please pair the monitor to your camera(s) !
(Please refer to the instructions below)
The monitor unit can be paired with a maximum of 2 cameras. Use the
Up/Down buttons in order to switch between the connected cameras or to show
a splitted screen.
General Usage:
Select the desired menu item by using the Up/Down buttons. Then confirm your choice
with the OK button. Press the Menu button to exit a submenu or wait a few seconds
without any input to exit automatically.
Power button
Press the Power button to power-on the monitor. The screen on the monitor will turn on
automatically when the vehicle is in reverse gear (when already paired to the camera(s)
as described below). When the monitor is on and gets a signal, the blue LED will light up,
otherwise it will blink. When the monitor is off, no picture will appear on the screen and
the blue LED will be off.
Menu / Return
Up /Auto Mode
Down / Manual Mode
OK (Confirm)
Lines
Power (On/Off)
8
MENU
Press the Menu button to enter the main menu screen.
PAIRING Menu
Here you can pair up to 2 cameras. Select CAM1 or CAM2 and press the OK button to
start the pairing process.
The device is now ready to pair to the camera (example: CAM1)
Now press the rubber button at the bottom of the camera !
9
Pairing successful.
Back in the PAIRING Menu a symbol appears next to the paired camera CAM1. The unit
will now pair automatically to the camera when powered on. If you have 2 cameras
(optional), please repeat the pairing process as described.
Press the Menu button to exit.
Example: Both cameras have been paired.
10
SETUP Menu
Select the desired sub-menu with the Up/Down buttons and confirm with the OK button.
The respective functions of the sub-menus are being described below.
SETUP-AUTO DISPLAY
This setting allows you to set your main view: The selected camera (CAM1 or CAM2) will
be displayed automatically when backing up. In order to show the picture of both
cameras at the same time, please select SPLIT in the menu (only if both signals can be
received – otherwise the monitor will show the available picture in fullscreen).
SETUP-MIRROR
Select CAM1 or CAM2 in order to mirror the displayed picture horizontally or vertically.
Table of contents
Languages:
Other pro user Digital Camera manuals
pro user
pro user DRC4340 User manual
pro user
pro user DRC4311 User manual
pro user
pro user RVC3110 User manual
pro user
pro user RPC3600 User manual
pro user
pro user APR043DC User manual
pro user
pro user DRC5040 User manual
pro user
pro user APR035X2 User manual
pro user
pro user APR043 User manual
pro user
pro user DRC4340 User manual
pro user
pro user DRC4310Solar User manual
