PRIZM 201840-xxx User manual

This manual suits for next models

1

Popular Network Card manuals by other brands

FirstComm

FirstComm OBiWiFi5G Setup guide

Sun Microsystems

Sun Microsystems Interface Adapter user guide

TRENDnet

TRENDnet TU2-ETG user guide

YASKAWA

YASKAWA SI-EN3 Technical manual

Paradyne

Paradyne BitStorm 2600 IP DSLAM installation guide

Belkin

Belkin F5D7050 user manual

3Com

3Com EtherLink 3C509B quick guide

TRENDnet

TRENDnet TEG-PCITX user guide

Cisco

Cisco MC16E installation guide

Delta Electronics

Delta Electronics Braking Modules VFDB Series instruction sheet

TwinMOS

TwinMOS Booming user manual

Dialogic

Dialogic Media Board DM/V1200BTEPEQ installation guide

Buffalo

Buffalo AirStation WLI-PCM-L11GP user manual

National Instruments

National Instruments NI 9234 operating instructions

Hama

Hama 49276 Operating instruction

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Product data

Compaq

Compaq Wireless LAN 100 specification

Bose

Bose PowerMatch Dante quick start guide

VME Dual Port Gigabit Ethernet

Media Converter Board

(P/N 201840 xxx)

User’s Manual

And

Troubleshooting Guide

February 24, 2009

Rev B

Moog Components Group

Springfield Operations

750 West Sproul Road

Springfield, PA 190 4

E-Mail: mcg@moog.com URL: www.moog.com/components

Tel: 610-328-4000 Fax 610-605-6216

24/7 Techn cal Customer Support Hotl ne: 610-605-6101

MOOG CG 201840-xxx VME Dual Port G gab t Ethernet Board Manual, Rev B February 24, 2009

Page 2 of 8

MANUAL REVISION HISTORY

REVISION

NUMBER

DATE BY REASON FOR

REVISION

A 8/7/08 GSG ORIGINAL

B 2/24/09 IB Updated contact nformat on to reflect

Moog Components Group

TABLE OF CONTENTS

1

VME DUAL PORT GIGABIT ETHERNET BOARD, P/N: 201840-XXX ..................................... 3

1.1

VME DUAL PORT GIGABIT ETHERNET BOARD REVISION HISTORY:............................................... 3

1.2

VME DUAL PORT GIGABIT ETHERNET BOARD DASH (-) NUMBER DEFINITIONS ............................ 3

1.3

VME DUAL PORT GIGABIT ETHERNET BOARD OPERATION:........................................................... 4

1.3.1 G gab t Ethernet Board Ind cators and Controls:............................................ 4

1.3.2 VME Dual Port G gab t Ethernet Board Spec f cat ons: ................................ 7

1.3.3 G gab t Ethernet board D mens ons:............................................................... 7

1.3.4 G gab t Ethernet board Power Requ rements: ................................................ 7

1.3.5 Power Sect on Test ng .................................................................................... 7

1.3.6 Opt cal Sect on Test ng................................................................................... 8

1.3.7 Ethernet Test ng .............................................................................................. 8

MOOG CG 201840-xxx VME Dual Port G gab t Ethernet Board Manual, Rev B February 24, 2009

Page 3 of 8

1 VME Dual Port Gigabit Ethernet Board, P/N: 201840 xxx

The Pr zm VME Dual Port G gab t Ethernet Med a Converter board prov des a f ber opt c

l nk to remote two ndependent G gab t Ethernet l nks over f ber opt c cable. Th s board

was des gned to spec f cally to support a G gab t Ethernet sonar – the Reson 7125 but the

board can be used n any appl cat on requ r ng G gab t Ethernet. An ndustry standard

pluggable small-form-factor (SFP) G gab t Ethernet (GBE) f ber opt c module s employed

to allow easy custom zat on of the f ber opt c l nk character st cs. S ngle mode f ber s

typ cally used w th th s board and opt cal l nks can eas ly exceed 10 k lometers. Mult mode

f ber can also be supported but w th drast cally reduced opt cal l nk d stance – typ cally less

than 1 k lometer depend ng on the f ber spec f cs.

Th s board has to be l nked w th another G gab t Ethernet board to complete the Ethernet

connect on.

NOTE: The Gigabit Ethernet board will only work with Gigabit Ethernet devices.

This board will not support 10 or 100 Mbps Ethernet.

The G gab t Ethernet board w ll operate as e ther a subsea or surface nterface board, so t

can be used as a spare for e ther locat on. The opt cal modules used on the board are

nherently b -d rect onal and care must be taken to ensure the correct opt cal port (e ther TX

or RX) s connected, depend ng on the board conf gurat on and system locat on. Wh le the

opt cal module’s rece ver w ll operate on all of the 16 CWDM (coarse wave d v s on

mult plex ng) wavelengths (1270 to 1610nm), the module’s transm tter only em ts at a

s ngle wavelength so care must be taken to ensure the correct wavelength s used.

For non-CWDM appl cat ons, Pr zm can supply the board w th SFP’s that conta n an

nternal b -d rect on WDM (wave d v s on mult plexers) for s ngle-f ber operat on.

1.1 VME Dual Port Gigabit Ethernet Board Revision History:

The G gab t Ethernet board has gone through the follow ng pr nted c rcu t board (PCB) and

Assembly rev s ons:

PCB Rev s on A/Assembly Rev s on A Or g nal des gn..

1.2 VME Dual Port Gigabit Ethernet Board Dash ( ) Number

Definitions

The G gab t Ethernet board has a Dash Number appended to the part number. Th s Dash

Number dent f es the spec f c board conf gurat ons:

-001A or g nal conf gurat on.

MOOG CG 201840-xxx VME Dual Port G gab t Ethernet Board Manual, Rev B February 24, 2009

Page 4 of 8

1.3 VME Dual Port Gigabit Ethernet Board Operation:

The G gab t Ethernet board has three ma n electr cal connectors: two Ethernet RJ-45

connectors and the DIN backplane connector for DC power. The board also has a s ngle 2-

p n Phoen x DC power connector f the board s used w thout a VME rack and backplane.

The RJ-45 connectors (J4 and J7) are located at the left s de of the board and are standard 8-

p n Ethernet connectors w th an ntegrated transformers. The RJ-45 connectors each have a

pa r of ntegrated Ethernet status LEDs.

There s s ngle DIN backplane connector (J1) mounted on the t ght s de of the board for

acqu r ng +5VDC power. Also a green 2-p n Phoen x connector (J2) s located on the on

the lower r ght s de of the board for supply ng the board w th DC operat ng power f the

backplane s not used. P n 1 (upper p n of the J2 connector and labeled “+5V”) s the

+5VDC nput and p n 2 (the bottom p n and labeled “GND”) s the ground.

The SFP opt cal modules (J3 and J6) are located on the left s de of the board.

NOTE: On power up of the board, both LEDs within RJ 45 connectors J4 and J7 will

briefly flash ON then OFF to indicate that the GBE chips (U5 and J9) are starting.

Even if the two boards are optically connected, neither LED on RJ 45 connectors J4

and J7 will light until a valid GBE signal is present at BOTH ends of the fiber optic

link. Once valid GBE signals are seen at both ends of the link then the LEDs on J4

and J7 will activate.

1.3.1 Gigabit Ethernet Board Indicators and Controls:

LEDS:

There are 3 through-hole r ght angle LED nd cators on the top of the board. There are no

LEDs on the bottom of the board.

Top of Board

LED Indication

D3 (Green) Located at the lower r ght of the board, labeled “+5V”, serves as an nd cator that +5VDC

power s ava lable to the board.

D5 (Green) Located on the upper left of the board, labeled “FIBER TRAFFIC #1”. LED bl nks ON

br efly when power s appl ed to the board, otherw se t s not l t.

D7 (Green) Located on the left center of the board, labeled “FIBER TRAFFIC #2”. LED bl nks ON

br efly when power s appl ed to the board, otherw se t s not l t.

D9 (Green) Located on the lower left of the board, labeled ‘TXD #2’, prov des an nd cat on that the

Cypress m croprocessor has responded to a data request from the PMON2 computer. Th s

LED s ON for the durat on of the transm tted data.

D11 (Green) Located on the lower left of the board, labeled ‘RXD #2’, prov des an nd cat on that the

Cypress m croprocessor has rece ved a data request from the PMON2 computer. Th s LED s

MOOG CG 201840-xxx VME Dual Port G gab t Ethernet Board Manual, Rev B February 24, 2009

Page 5 of 8

ON for the durat on of the rece ved data.

D8 (Green) Located on the lower left of the board, labeled ‘TXD #1’, prov des an nd cat on that the

Cypress m croprocessor has responded to a data request from the PMON2 computer. Th s

LED s ON for the durat on of the transm tted data.

D10 (Green) Located on the lower left of the board, labeled ‘RXD #1’, prov des an nd cat on that the

Cypress m croprocessor has rece ved a data request from the PMON2 computer. Th s LED s

ON for the durat on of the rece ved data.

Bottom of Board

LED Indication

D1 (Green) Located at the upper front edge of the board, labeled “+3.3V”, serves as an nd cator that

+3.3V DC s be ng generated by the on-board DC-DC power supply. Supply voltage 5V

must be present for th s LED to be act ve.

D4 (Green) Located on the upper front edge of the board, labeled “FIBER #1”, prov des an nd cat on that

the transce ver module has detected the presence of an nput s gnal on the f ber l nk. When

‘ON’ nd cates that th s board has a good level of rece ved opt cal power from the remote un t

A.

NOTE: THIS LED WILL BE ON WHETHER ETHERNET DATA IS PRESENT OR

NOT.

D6 (Green) Located on the upper front edge of the board, labeled “FIBER #2”, prov des an nd cat on that

the transce ver module has detected the presence of an nput s gnal on the f ber l nk. When

‘ON’ nd cates that th s board has a good level of rece ved opt cal power from the remote un t

B.

NOTE: THIS LED WILL BE ON WHETHER ETHERNET DATA IS PRESENT OR

NOT.

FUSES:

There s one fuse for th s board. All fuses are the self-resett ng PTC type and should

qu re replacement by the user.

F1: 1.1 Amp PTC, DC nput fuse at J2

SWITCHES:

There are no sw tches on th s board.

TRIMPOTS:

There are no tr mpots on th s board.

CONNECTORS:

There are a total of 9 connectors on the board.

J1: 96-p n DIN backplane connector

MOOG CG 201840-xxx VME Dual Port G gab t Ethernet Board Manual, Rev B February 24, 2009

Page 6 of 8

J2: 2-p n Phoen x connector for DC power entry

J2 DC Power 2-p n Phoen x Connector

o

1 +5VDC Input

o

2 Ground

J3: SFP opt cal module for L nk #1

J4: RJ-45 GBE Ethernet connector for L nk #1

J5: 5-p n header for U5 programm ng – do not use

J6: SFP opt cal module for L nk #2

J7: RJ-45 GBE Ethernet connector for L nk #2

J8: 5-p n header for U9 programm ng – do not use

J9: 3-p n Phoen x connector for RS-485 PMON2 D agnost cs

J9 3-p n Phoen x Connector for D agnost cs

o

1 RT+

Left o

o

o

o

o

o

o

o

R ght

J4 G gab t Ethernet

RJ-45 Connector P n # 8

7

6

5

4

3

2

1

P n # 1000Mbps

1 A+

2 A-

3 B+

4 C+

5 C-

6 B+

7 D+

8 D-

Left o

o

o

o

o

o

o

o

R ght

J6 G gab t Ethernet

RJ-45 Connector P n # 8

7

6

5

4

3

2

1

P n # 1000Mbps

1 A+

2 A-

3 B+

4 C+

5 C-

6 B+

7 D+

8 D-

MOOG CG 201840-xxx VME Dual Port G gab t Ethernet Board Manual, Rev B February 24, 2009

Page 7 of 8

o

2 Ground

o

3 RT-

JUMPER POSTS:

There are 4 jumper posts on th s board.

JP1 1 o==o 2 enables SFP Laser transm tter for J3

JP2 1 o==o 2 enables SFP Laser transm tter for J6

JP3 Cypress programm ng header for U12 – do not use

JP4 Cypress programm ng header for U11 – do not use

1.3.2 VME Dual Port Gigabit Ethernet Board Specifications:

Number of Ethernet l nks: 2 per board

Data rates supported: G gab t Ethernet only

1.3.3 Gigabit Ethernet board Dimensions:

Pr nted c rcu t board (PCB): 3.937 nches x 6.299 nches

(100mm x 160 mm)

1.3.4 Gigabit Ethernet board Power Requirements:

The G gab t Ethernet board

ut l zes approx mately 2.5 Watts of power.

• 5.0VDC nput, approx mately 500mA

1.3.5 Power Section Testing

NOTE: The connectors and components on the bottom of the Gigabit Ethernet board

have pins that are connected to internal supply voltages and ground. If these pins are

inadvertently shorted together or to a common chassis ground, the board fuse ( 1) will

trip/reset.

If both the “+5V” LED and the “+3.3V” LED s out:

• Check for cont nu ty of PTC fuse F1 w th an ohmmeter.

• Replace PTC fuse f open.

If only the “+3.3V” LED s out:

• Ver fy +5VDC voltage s present at the source

• Replace the board w th a spare, noth ng repa rable.

MOOG CG 201840-xxx VME Dual Port G gab t Ethernet Board Manual, Rev B February 24, 2009

Page 8 of 8

1.3.6 Optical Section Testing

1.3.7 Ethernet Testing

If the Ethernet l nk s out or has errors:

• As th s board w ll only work w th G gab t Ethernet traff c, ver fy that the dev ces at both

ends of the l nk are ndeed G gab t Ethernet dev ces.

• Ver fy that the Ethernet dev ces at both ends of the l nk are powered up.

• Ver fy that both of the dual LEDS at J4 and J7 are l t to conf rm Ethernet act v ty at the

RJ-45 connector.

• Attempt to PING from one dev ce to the other.

• If the channel s st ll not operat ng correctly, f rst check the f eld w r ng. If the w r ng

appears correct, then f rst replace the subsea G gab t Ethernet board w th a spare and

check the l nk aga n. If the problem s st ll there, replace the surface G gab t Ethernet

board, w th a spare and check the l nk aga n.