prime3 SAP81 User manual
Air purifier
Luftreiniger
Oczyszczacz powietrza
SAP81
Owner’s manual
Bedienungsanleitung
Instrukcja obsługi
SAP81
5
2
3
1
4
9 14 1016
6 7 8 11 12 13
1
2
SAP81
3
4
SAP81
5
1
2
3
4
5
6
7
8
5
Important notes
Before using this device read the instruction manual and follow the
instructions inside. The manufacturer is not liable for any damages
caused by the misuse of this device due to inappropriate handling.
Please keep this manual for future reference.
· This device is for domestic use only. Do not use for any other
purposes.
· The device should only be connected to an earthed socket with
values corresponding to the values on the rating label.
· The device is not designed to be controlled via an external timer,
separate remote control, or other equipment that can turn the device
on automatically.
· Before maintenance work always disconnect the unit from the power
supply.
· Never leave the product connected to the power source without
supervision.
· Never put the power cable, the plug or the whole device into the
water or any other liquids.
· The device should be cleaned regularly complying with the
recommendations described in the section on cleaning and
maintenance.
· Do not place the device near sources of heat, flame, an electric
heating element or a hot oven. Do not place on any other device.
· This equipment can be used by children aged 8 years and over under
as long as supervision is provided. People with reduced physical or
mental capabilities, as well as people with no previous experience of
using this equipment must be supervised and made aware of the
risks. The instruction manual should be used as a reference for the
safe use of this equipment. Children should not play with the
equipment. Children without ensured supervision should not be
allowed to perform the cleaning and maintenance of equipment.
· Additional precautions should be taken when using this device in the
presence of children or pets. Do not allow children to play with the
SAP81
6
device.
· Never use the product close to combustibles.
· Never expose the product to atmospheric conditions such as direct
sun light or rain, etc... Never use the product in humid conditions (like
bathroom or camping house).
· The AC adapter should be connected to an outlet with characteristics
consistent with the values on the rating label.
· If the cord or power plug or adaptor is damaged or the plug has a
loose electrical outlet, do not charge the device and do not power it
from the mains.
· Unplug the AC adapter from the electrical outlet when not in use.
· Do not connect or disconnect the adaptor from the power source
with wet hands.
· The power cable should be periodically checked for damage. If the
power cable is damaged the product should be taken to a
professional service location to be fixed or replaced to prevent any
hazards from arising.
· Never use the product with a damaged power cable or if it was
dropped or damaged in any other way or if it does not work properly.
Do not try to repair the defected product by yourself as it can lead to
electric shock. Always return the damaged device to a professional
service in order to repair it. Authorized service professionals should
only perform all the repairs. Any attempted unauthorized repairs
performed can be a hazard to the user.
· Only Original accessories should be used, as well as accessories
recommended by the manufacturer. Using accessories, which are not
recommended by the manufacturer, may result in damage of the
device and may render the device unsafe for use.
· Do not put fingers or any other objects in the inlet/outlet holes of the
device.
· Place the device in way that does not interrupt the air inflow/outflow,
leave at least 30 cm of space from each side of the device.
SAP81
7
· Do not use the device if the filter is completely utilized, not installed
or not properly installed.
· Do not use in spaces where chemical agents are used, such as: paints,
varnishes, glues, insecticides, air fresheners.
Device is compliant with EU directives:
- Low voltage directive (LVD)
- Electromagnetic compatibility (EMC)
Device marked CE mark on rating label
When this crossed-out wheeled bin symbol is attached to a product it means that the product is
covered by the European Directive 2012/19/EU. Please inform yourself about the local separate
collection system for electrical and electronic products. Used appliance should be delivered to the
dedicated collecting points due to hazardous components, which may affect the environment. Do
not dispose this appliance In the common waste bin.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into
three materials: cardboard (box),polystyrene foam(buffer) and poly ethylene (bags, protective foam sheet).
Your system consists of material which can be recycled and reused if disassembled by a specialized company.
Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and
old equipment.
Your products is designed a manufactured with high quality materials and components, which can
be recycled and reused.
Technical specification and parameters of the appliance
Power supply: 220-240V ~ 50 / 60Hz
Rated power: 80W
Dimensions: 37 x 19,5 x 65cm
Weight: 8kg
Accessories:
Filter set (cold catalysis + activated carbon + antibacterial + HEPA filters): SAP81.1
Pre-filter: SAP81.2
SAP81
Your product contains batteries covered by the European Directive2006/66/EC, which cannot be
disposed with normal household waste. Please inform yourself about the local rules on separate
collection of batteries because correct disposal helps to prevent negative consequences for the
environmental and human health.
8
CLEANING AND MAINTENANCE
Do not immerse the device in water. Wipe the surface with a damp cloth, then wipe dry.
Before carrying out maintenance work, make sure that the device is disconnected from the power supply.
The pre-filter is washable, it can be cleaned in water, dry the filter before further use.
Filters (cold catalysis + activated carbon + antibacterial + HEPA) are not washable; do not immerse them in
water. The filters can be cleaned using a vacuum cleaner with a soft brush. The filters are extremely delicate;
they must not be pressed too much when vacuuming.
If the device is operated under normal conditions, it is recommended to replace the filters every 6 months
(cold catalysis + activated carbon + antibacterial + HEPA) assuming that the device works approx. 8 hours a
day. In case of strong air pollution or prolonged use, the filter may require more frequent replacement. It is
recommended to clean the filters every 60 days. It is recommended to clean the pre-filter every 15 days.
Maintenance of the ionizer head (Fig. 3)
It is recommended to clean the ionizer head from the dust with a dry brush, if the device starts to make
sounds resembling crackles. Insert a soft brush through the air outlet opening above the ionizer head.
Regularly remove the dust that accumulates near the ionizer head.
Maintenance of the particles sensor (Fig.4)
Pollution sensor - it is recommended to clean the particle sensor every 2 months. To clean the sensor, remove
its cover and then clean the lens with a dry cotton swab.
Installation / replacement of filters (Fig.5):
1. Press in the points marked on the picture to unclip the front panel of the device.
2. Remove the front panel.
3. Remove all filters from the device.
4. Remove the HEPA + antibacterial filter, the cold catalysis filter + activated carbon filter and the pre-filter
from plastic packaging.
5. Insert the HEPA + antibacterial filter so that the side with the handle is facing you.
6. Insert the cold catalysis filter + activated carbon so that the side of the handle is facing you.
7. Insert the pre-filter so that the side of the handle is facing you.
8. Install the front panel.
Switching on the device
· On / off switch (10) - press the switch to switch on the purifier. The device will automatically switch to the last
saved operating mode (excluding the timer and night mode settings). The device will not turn on if it is not in
an upright position or the front panel is not correctly installed).
· Press the button to turn off the device.
1. Control panel.
2. Air inlets.
3. Air outlet.
4. Handle.
5. Front panel.
Control panel buttons:
6. Smart Mode.
7. Cleaning speed.
8. Night mode.
9. UV sterilization.
10. ON / OFF switch.
11. Timer.
12. Ionizer.
13. Child lock.
14. Purifying speed indicator.
15. Filter replacement indicator.
16. Air quality indicator.
SAP81
Description of the device function
1. Smart Mode (6) - in Smart mode, the device will adjust the work to the level of pollution. PM2.5 particle level
below 60 (basic speed), below 150 (average speed), above 150 (high speed).
2. Purifying speed (7) - the button allows you to control the purifying speed, basic (500RPM), medium
(700RPM), high (900RPM).
3. Night mode (8) - After pressing the button, the device will go to night mode after 5 seconds. In this mode,
the device operates at the basic purifying speed and the control panel backlight is turned off. Press any button
to exit the night mode.
4. UV Sterilization (9) - press the UV sterilization button to turn the device on or off.
5. Timer (11) - pressing the button will start the timer function, each press extends the working time by 30
minutes. The minimum time is 30 minutes, maximum time is 12 hours. Press and hold the button for 3 seconds
to turn off the timer function.
6. Ionizer (12) - pressing the button will start the air ionization process. The ionization icon will be highlighted.
7. Child lock (13) - pressing the button will cause the buttons to not react to pressing, and the device will
operate in the previously selected operating mode. Press and hold the button for 3 seconds to disable the
lock. The icon will be illuminated when the child lock is on.
8. Purifying speed indicator (14) - the indicator shows the current air purifying speed, basic (500RPM), average
(700RPM)
Remote control:
The device has been equipped with a remote control powered by button batteries (CR2032). The remote
control has the same set of buttons as the target device.
Comments:
Before first use, open the battery cover and remove it from the packaging. Then re-insert, otherwise the
remote control will not work. If you do not intend to use the remote control for a long time, remove the
battery.
Clock settings:
1. Press and hold the Smart Mode button (6) for 5 seconds to activate the clock settings. Use the purge speed
(7) and night mode (8) buttons to set the hour. Press the Smart Mode button (6) once again to go to the
minute settings; set the number of minutes using the cleaning speed (7) and night mode (8) buttons, wait a
few seconds and the set time will be saved.
9
SAP81
WICHTIGE INFORMATIONEN
Um die größte Zufriedenheit zu erreichen, sich an der Effektivität des
Produktes zu erfreuen und alle seine Eigenschaften und Funktionen
kennenzulernen, bitten wir Sie, sich mit dieser Anleitung vertraut zu
machen, bevor Sie mit der Verwendung dieses Produktes beginnen.
· Vor Nutzungsbeginn des Gerätes bitte die Bedienungsanleitung
durchlesen und laut den enthaltenen Hinweisen vorgehen. Der
Hersteller übernimmt keine Verantwortung für Schäden, die durch
nicht bestimmungsgemäße Nutzung oder falsche Bedienung
entstanden sind. Die Bedienungsanleitung sollte so aufbewahrt
werden, damit sie auch bei der späteren Nutzung des Gerätes zur
Verfügung steht.
· Das Gerät dient ausschließlich dem Hausgebrauch. Das Gerät darf
nur gemäß seiner Bestimmung genutzt werden.
· Das Gerät darf ausschließlich an eine Steckdose mit der, dem
Typenschild entsprechenden Charakteristik, angeschlossen werden.
· Überprüfen Sie, ob die gesamte Leistungsaufnahme aller, an der
Wandsteckdose angeschlossenen Geräte, die maximale Belastung
der Sicherung nicht überschreitet.
· Wenn ein Verlängerungskabel benutzt wird, muss man überprüfen,
ob die gesamte Stromabnahme der an das Verlängerungskabel
angeschlossenen Geräte, die maximalen Belastungsparameter des
Verlängerungskabels nicht überschreitet. Das Verlängerungskabel
soll so verlegt werden, dass das zufälliges herausreißen und stolpern
vermieden wird.
· Vermeiden Sie, dass das Versorgungskabel über eine Tisch- oder
Regalkante hängt, oder eine heiße Fläche berührt.
· Das Gerät ist nicht für eine Steuerung mit einem externen
Zeitschalter, einer getrennten Fernbedienung oder einer anderen
Einrichtung, die das Gerät automatisch einschalten können,
bestimmt.
· Vor Wartungsarbeiten muss das Gerät unbedingt vom Netz getrennt
werden. Bei der Trennung des Versorgungskabels muss man es
10
SAP81
This manual suits for next models
2
Table of contents
Languages:
Other prime3 Air Cleaner manuals
