Premier Mounts PP-FCTA User manual

CEILING MOUNT MODEL

Premier Mounts

3130 E. Miraloma Avenue

Anaheim, CA 92806

Phone: (800) 368-9700 Fax: (800) 832-4888

[email protected] www.mounts.com

9530-302-001-03

INSTALLATION MANUAL

The PP-FCTA is designed

to be installed above the

ceiling tiles.

- 2 -

oSafety & Precaution 2

oDiagrams 3

oParts list 4

oPlate assembly 4

oSecuring the plate 5

oElectrical cut out 6

oCeiling anchoring 7

The ceiling structure must be capable of supporting at least five (5) times the weight of projector. If not, the ceiling structure

must be reinforced. Proper installation procedure by qualified personnel as outlined in the installations instructions must be

adhered to. Failure to do so could result in serious personal injury.

The entire installation instructions should be fully read and understood, including all of the safety symbols and safety

precautions, before beginning installation. The installation instructions should be read, understood and followed to prevent

personal injury or property damage. Keep these installation instructions in an easily accessible location for future reference.

Indicates that the power plug is to be disconnected

from the power outlet.

Safety precautions must be taken at all times.

Contact Premier Mounts for an

uestions

Warning and caution in general

Do not install near heater, direct sunlight or air conditioning or any other source of direct heat energy. Failure to do so

may result in damage to the projector.

A qualified person should always perform the installation work.

Safety & Precautions

WARNING: Safety precaution measures must be practiced at all times during the installation of this product. Use proper safety gear and

tools for the installations procedure to prevent personal injury.

- 3 -

SPECS

PART#:

PP-FCTA False ceiling mount

COLOR:

White

A. Ceiling main plate

B. 1½" (NPT) adapter plate

C. Ceiling stud plate

D. (6) Turnbuckle mounting

points

F. (4) Securing points

E. (2) Electrical cut outs

Diagrams

- 4 -

Phillips screwdriver, Pliers, Wire cutters

(Other tools required depending on the installation environment)

Parts List

TOOLS & SUPPLY NEEDED

Plate assembly

Step 1

NOTE: Read all cautions and warnings before

continuing.

Assemble the plate together. Pre-set all the M5 x 16

Phillips screws two (2) on both outer ends of the plate

and one (1)

found on the 1½" (NPT) nipple.

Observe the room and the ceiling; find the proper

location for the projector placement and lightly mark the

bottom of the tile. Remove any of the 24" x 24" or 24" x

48" tiles that are surrounding the marked tile. Measure

3" from the edge of the t-bar to the inside of the tile. The

hole excepting the pipe should be cut anywhere inside

the square. Place the ceiling plate on the t-bar rails. See

figure 1.

HARDWARE

¼-20

Turnbuckles

(Qty 4)

(5) M5 x 16 Phillips

head screws

(Pre-assembled)

¼-20 Wing nuts

(Pre-assembled)

(Qty 4)

14 (GA)

Galvanized steel

wire

¼" x 3"

Lag bolts

(Qty 4)

Escutcheon ring

Loosel

install the

lates

Ceiling main plate

Slider plate

(4) M5 x 16 Phillips

hex screws

(1) M5 x 16mmPhillip screw

(safety screw)

(4) ¼"-20 wing nuts

1½" (NPT) adapter

late

Ceiling stud plate Remove tile

Or any of the

surroundin

tiles

T-bar frame rails

Measure and cut

Figure 1

- 5 -

Step 2

Cut a hole on the marked tile where the 1½" (NPT) close nipple or

pipe (optional) will be secured to the plate. Position and slide the

stud plate to the hole and secure the ceiling plate to the rails by

tightening the four (4) M5 x 16 Phillips head screws (supplied).

Center the stud plate to the hole and secure the plate by tightening

the four win

nuts. See fi

ure 2

Securing the plate

Step 3

Secure the 1½" (NPT) nipple to the ceiling plate and secure the nipple

by using one (1) M5 x 16 Phillips head screw (supplied) to the stud

plate.

Tiles

T-bar frame rails

Align with the cut out

and tighten the wing

nuts

Tighten M5 x 16mm Set Screw

to secure the plate to the rail

framing. The M5x16mm screw

may be installed from either the

outside or the inside of the plate.

Ceiling main plate

Tiles

1½" (NPT) nipple

Tighten M5 x

16mm Safety

Screw to secure the

1½" (NPT) nipple

T-bar frame rails

CAUTION: The main ceiling plate has to rest on the t-bar main

frame. Use the four (4) M5 x 16 Phillip head screws to secure the

plate. Failure to do so may result in the instability of the plate.

NOTE: If more ceiling drop is required, use longer pipe call

Premier Mounts Inc For longer pipe size (optional).

CAUTION: The M5 x 16 Phillip head screw must be used to

stabilize the 1½" (NPT) nipple or optional pipe.

Figure 2

Figure 3

- 6 -

CUT

Electrical cut out

Step 4

NOTE: The electrical installation should be done in accordance

to local codes and regulations.

Cut the tile where the electrical base box is going to be secured.

Using (commercially available) hardware depending on electrical

installation environment, Install the electrical box and secure it to

the plate. Make all electrical connections at this time.

See figure 4 & 5.

Tiles

Ceiling main plate

Electrical box

cut ou

Electrical box

(

commerciall

available

)

Tiles

T-bar frame rails

T-bar frame

NOTE:The electrical cut outs allow for a single and square

electrical box installations.

Figure 4

Figure 5

- 7 -

Thank you for choosing PREMIER MOUNTS for your installation needs.

If you have any questions please contact PREMIER MOUNTS

Information is shown on the front of this page.

Ceiling anchoring

Step 5

Wood joist: Secure the four (4) ¼" eye lag screws to the wood

joist on the ceiling. Make sure eye lag screws are properly

secured to the joist before securing the wire to the turnbuckles

on the plate.

Concrete: Use (commercially available) suitable hardware

depending on your installation environment. And follow the

instructions below.

Truss ceiling: Use (commercially available) suitable hardware

depending on your installation environment. And follow the

instructions bellow.

Loop the wire through the eye lag screws, anchors, or truss and

twist the wire at least five (5) times itself to secure it. Run the

other end of the wire through the turnbuckle and twist the wire

at least five (5) times around itself to secure it.

See figure 6 & 7.

CAUTION: The final loop on the wire has to tightly bend and

secured to the wire to prevent the wire from untwisting itself.

Twist the turnbuckles to fine tune adjust.

CAUTION: Recheck all hardware and installation for proper

tightness and security and replace the til

Tiles

Ceiling main

Turnbuckles

14 (ga) Wire

htl

secured

Concrete Wood joist Truss

CAUTION: Loop the 14 (ga) wire at

least 5 times around itself. The final

loop has to be secured to prevent the

wire from becoming untied.

Do this for the eye lag screws and

turnbuckles

T-bar frame rails

Figure 6

Figure 7

Other manuals for PP-FCTA

Table of contents

Other Premier Mounts Rack & Stand manuals

Premier Mounts

Premier Mounts AM95 User manual

Premier Mounts

Premier Mounts iPad IPM-500 User manual

Premier Mounts

Premier Mounts PSM-442T User manual

Premier Mounts

Premier Mounts AM500 User manual

Premier Mounts

Premier Mounts Universal Tabletop Stand PSD-TTS Guide

Premier Mounts

Premier Mounts CTM-MS1 User manual

Premier Mounts

Premier Mounts LMVSP User manual

Premier Mounts

Premier Mounts AM3 User manual

Premier Mounts

Premier Mounts PRF User manual

Premier Mounts

Premier Mounts MVW55 User manual

Premier Mounts

Premier Mounts 7170-0977 Series User manual

Premier Mounts

Premier Mounts SHLF-VC User manual

Premier Mounts

Premier Mounts PP-6 User manual

Premier Mounts

Premier Mounts TTS-BASE-L User manual

Premier Mounts

Premier Mounts AM100 User manual

Premier Mounts

Premier Mounts PSD-TS User manual

Premier Mounts

Premier Mounts RTM Series User manual

Premier Mounts

Premier Mounts LMV User manual

Premier Mounts

Premier Mounts PTM User manual

Premier Mounts

Premier Mounts Universal Flat-Only Mount UFM User manual

Premier Mounts

Premier Mounts GB-PIPE1 User manual

Premier Mounts

Premier Mounts CTM-MS2 User manual

Premier Mounts

Premier Mounts PRC-LA User manual

Premier Mounts

Premier Mounts PSD-TS User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 