Polycom 5300LF2 VBP-E Series Installation instructions
Polycom® VBP™ 5300LF2 System
Hardware Guide
June 2011 |3725-73553-001A
5300LF2 Hardware Guide
1
Trademark Information
Polycom®, the Polycom “Triangles” logo, and the names and marks associated with Polycom’s products are trademarks and/or service marks of
Polycom, Inc., and are registered and/or common-law marks in the United States and various other countries.
All other trademarks are the property of their respective owners.
© 2010 Polycom, Inc. All rights reserved.
Polycom, Inc.
4750 Willow Road
Pleasanton, CA 94588-2708
USA
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the
express written permission of Polycom, Inc. Under the law, reproducing includes translating into another language or format.
As between the parties, Polycom, Inc., retains title to and ownership of all proprietary rights with respect to the software contained within its
products. The software is protected by United States copyright laws and international treaty provision. Therefore, you must treat the software like
any other copyrighted material (e.g., a book or sound recording).
Every effort has been made to ensure that the information in this document is accurate. Polycom, Inc., is not responsible for printing or clerical
errors. Information in this document is subject to change without notice.
5300LF2 Hardware Guide
2
5300LF2 VBP-E Series Physical connections and LED’s
A Erase
1 Click - Nothing
2 Clicks - Reset CLI password and restarts the system
3 Clicks - Restore to factory default
B Port 3 - Management interface
1 x 10/100/1000 Mbps Ethernet port for optional management network
connectivity, this interface must not be on the same network as the WAN or LAN
subnets. This network cannot be within a subnet contained in a “Route”
statement
C Port 2 - WAN interface
1 x 10/100/1000 Mbps Ethernet port for connectivity to the WAN or Internet
network connectivity
Default IP: none
D Port 1 - LAN interface 1 x 10/100/1000 Mbps Ethernet port for LAN network connectivity
Default IP: 192.168.1.1
E Console 1 x RS-232 8 pin modular console port for management – 9600-N-8-1 NONE for
flow control – 8 pin modular to DB9 cable provided in system box
F USB Currently not used
5300LF2 Hardware Guide
3
Symbol Function Color Signal
Power Status Green
Off – No Power, the system is off
On – Power is good, the system is on
G
Data Status Red
Off – No data access to the IDE drive
On – Data is being written to the IDE drive
5300LF2 Hardware Guide
4
Label Color Indication Status
Green or
other On
1: Ethernet port is receiving power
2: Good link between the Ethernet port and the connected switch
Off
1: The adapter and switch are not receiving power
2: No connection between both ends of the network cable, check cable,
replace cable.
ACK/LINK
Green or
other Flashing The adapter is sending and receiving network data. The frequency of the
flashing varies with the amount of data being transferred.
Yellow On ACK/LINK LED must be on. This LED will show the system operating at
1000 Mbps
Green On ACK/LINK LED must be on. This LED will show the system operating at
100 Mbps
Speed
Off ACK/LINK LED must be on. This LED will show the system operating at
10 Mbps
5300LF2 Hardware Guide
5
H Input Power Socket Accepts 3-pin Shroud Female plug for input power
I On/Off Switch Used to turn the system on and off
J VGA Currently not used
5300LF2 Hardware Guide
6
Connecting to the 5300LF2 VBP-E Series for the First Time
The VBP Series appliance is shipped with a pre-configured IP address on Port 1 of 192.168.1.1
1. Connect the 3-pin Shroud female plug of the power cord into the input power socket in the system shown as (H) in the above figures and
the other end to a wall AC outlet.
2. Turn the system power on by pressing on the top part of the power switch shown as (I) in the above figures.
3. Connect a computer using an IP address of 192.168.1.2 and subnet mask of 255.255.255.0 to Port 1 shown as (D) in the above figures
with either a Ethernet switch or a Ethernet cable wired directly to the computer.
4. Launch a Web browser on the computer and enter the http://192.168.1.1 Press Return. The main configuration menu appears - enter
the username root and the password default.
5. The EULA license agreement will now be displayed. After reading the license agreement, click “I agree” at the bottom to continue
configuring the system.
Configure the Network parameters as defined in the Configuration Guide contained on the VBP Documentation Library CD provided with the
system. The Configuration Guide is also available on the Polycom Web site.
5300LF2 Hardware Guide
7
5300LF2 VBP-ST series Physical connections and LED’s
A Erase
1 Click - Nothing
2 Clicks - Reset CLI password and restarts the system
3 Clicks - Restore to factory default
B Port 3 - Management interface
1 x 10/100/1000 Mbps Ethernet port for optional management network
connectivity, this interface must not be on the same network as the WAN or LAN
subnets. This network cannot be within a subnet contained in a “Route” statement
C Port 2 - Provider interface
1 x 10/100/1000 Mbps Ethernet port for connectivity to the Provider or LAN
network connectivity
Default IP: none
D Port 1 - Subscriber interface
1 x 10/100/1000 Mbps Ethernet port for Subscriber or WAN/Internet network
connectivity
Default IP: 192.168.1.1
E Console 1 x RS-232 8 pin module console port for management – 9600-N-8-1 NONE for
flow control – 8 pin modular to DB9 cable provided in system box
F USB Not used
5300LF2 Hardware Guide
8
Symbol Function Color Signal
Power Status Green
Off – No Power - the system is off
On – Power is good - the system is on
G
Data Status Red
Off – No data access to the IDE drive
On – Data is being written to the IDE drive
5300LF2 Hardware Guide
9
Label Color Indication Status
Green or
other On
1: Ethernet port is receiving power
2: Good link between the Ethernet port and the connected switch
Off
1: The adapter and switch are not receiving power
2: No connection between both ends of the network cable, check cable,
replace cable.
ACK/LINK
Green or
other Flashing The adapter is sending and receiving network data. The frequency of the
flashing varies with the amount of data being transferred.
Yellow On ACK/LINK LED must be on. This LED will show the system operating at
1000 Mbps
Green On ACK/LINK LED must be on. This LED will show the system operating at
100 Mbps
Speed
Off ACK/LINK LED must be on. This LED will show the system operating at
10 Mbps
This manual suits for next models
2
Table of contents
Other Polycom Conference System manuals
Polycom
Polycom MOBILE RESPONDER 3725-23487-003/A User manual
Polycom
Polycom RMX 2000 Installation instructions
Polycom
Polycom ViewStation SP128 User manual
Polycom
Polycom VSX 3000 Service manual
Polycom
Polycom iPower 9800 User manual
Polycom
Polycom ViewStation FX4000 User manual
Polycom
Polycom HDX Series User manual
Polycom
Polycom RealPresence Group Series Use and care manual
Polycom
Polycom SoundStructure C16 Manual
Polycom
Polycom VSX 7000e Series User manual
Polycom
Polycom VSX 7000e Series Instruction Manual
Polycom
Polycom VSX VSX 6000 User manual
Polycom
Polycom SoundPoint IP 500CS User manual
Polycom
Polycom HDX Desktop Systems Quick reference guide
Polycom
Polycom HDX 4500 User manual
Polycom
Polycom RealPresence Group 700 system User manual
Polycom
Polycom ViaVideo User manual
Polycom
Polycom realpresence trio 8800 User manual
Polycom
Polycom RealPresence 4000 User manual
Polycom
Polycom ViewStation H.323 User manual
Popular Conference System manuals by other brands
Kramer
Kramer VIA GO quick start guide
AVT
AVT MAGIC AC1 Go Configuration guide
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO user manual
Sony
Sony PCS-I150 Operation guide
Middle Atlantic Products
Middle Atlantic Products VTC Series instruction sheet
Prentke Romich Company
Prentke Romich Company Vanguard Plus Setting up and using
