Plumbworld Bath Screen User manual
Bath Screen
ASSEMBLY GUIDE
Please note hand tools NOT supplied.
PH2 TYPE
Screwdriver
7mm Masonry Drill
3.2mm HSS Drill
Drill Tape Measure Sealant Gun
Spirit Level
Pencil
1.. The screen can be constructed either way up, f ht hand opening.
2.. These ins st of parts assume that inst s
alt consult a hardware supplier for the correct type.
It may also be necessary to c correct method f
3.. Please check this product for damage prior to st st c er the
products has been fi er fi ng has commenced.
4.. Please note the minimum and maximum adjustment for this product are based on perfectly plumb walls.
EXPOLDED VIEW AND PARTS LIST
1 Glass Panel 1
2 13489-1 Wall Channel 1
1
3 SL205&6-4 Bo om Seal 1
4
5
S1PS07 Screw
Cup
2
2
6
S1PS08 Screw Cap
3
7
SBLTL001 Wall Plug
2
8
9
SBLTL003 Tapping Screw ST3.5*12
3
SBLTL013 Tapping Screw ST4*30
Parts List
1.Glass Panel
5.Screw Cap
2.Wall Channel
9.Waterproof part
Waterproof part
6.Wall Plug
4.Screw Cup
8.ST4x30
7.ST3.5x12
This assembly guide is suited to the Square bath screen,
Radius bath screen and Sail bath screens.
Step A
Place the screen onto the bath and ensure the glass arc can fit with the bath arc. Now the wall channel can be placed
int s ce is to place the wall channel onto the bath approx 50mm-60mm far from the edge of bath
as shown in A.1 . Although it may look more a to place the glass screen in the middle of the bath shoulder, it
may lead to some small amounts of water leaving the bath. It is best to place the screen above the inside edge of the
bath.
Place the wall channel 13489-1 ont er ensuring it is plumb mark the
by marking the wall with a pencil through
the pre-drilled holes in the wall channel. It is advisable to place some masking tape
or similar ont fore marking and drilling the holes. Not only will this allow
you tstop the drill bit from
causing you to drill off target. Drill 3 holes with a 6mm masonry
drill bit and insert wall plugs SBLTL001. Plugs provided are for standard plasterboard
walls, we advise you seek proffesional help to ensure you are using the correct wall
fixings for your wall.
Step C
Drill 3 equally spaced holes with a 3mm drill bit
through the wall channel and the bath screen
cal aluminium profile. Now fix the bath screen
cal profile using screws SBLTL003. Ensure you
use the screw cover cups S1PS07 at this stage. Now
finish by pushing the screw cover caps S1PS08 onto
the cups to hide the screw heads.
B
A.2
C.1 C.2
Step B
Fix the wall profile to the wall with screws SBLTL013.
Approx
50mm-60mm
A.1 A.3
Step F
Applying Silicone Sealant And Cleaning
Seal from the top of the wall channel to the bo om on the INSIDE and Outside between the wall channel and the wall.
W
aggressive or abrasive cleaning products.
24 HRS
DO NOT USE THE
ENCLOSURE FOR
24 HOURS AFTER
SEALING
SC-F
BLEACH
WHITE
SPIRIT
Step D
Put the bo om seal SL205&6-4 on the bo om of
the screen.
Note: The bo om seals require trimming.
D
Check out our full range of Bathroom Suites
Bathroom Suites By Range
Cloakroom Suites
Toilets
Bathroom Sinks / Wash Basins
Bidets
Baths
Wide variety of toilets
Close Coupled Toilets
Wall Hung Toilets
Back To Wall Toilets
Furniture unit toilets
Huge Selection of Baths
Acrylic Baths
Steel Baths
Shower baths
Freestanding baths
Small baths
Corner baths
Whirlpool baths
Don’t forget the important bathroom suite extras
Bath panels
Toilet seats
Other Plumbworld Bathroom Fixture manuals
