Planet ISW-1022MT User manual

8-Port 10/100Mbps + 2G TP/SFP Combo

Managed Industrial Switch

ISW-1022M / ISW-1022MT / ISW-1022MP /

ISW-1022MPT / ISW-1033MT

Quick Installation Guide

Table of Contents

1. Package Content.......................................................................................... 3

2. Requirements .............................................................................................. 4

3. Wiring the Power Inputs............................................................................... 5

4. Terminal Setup ............................................................................................ 6

5. Logon to the Console ................................................................................... 7

6. Congure IP address.................................................................................... 8

7. Start Web Management...............................................................................10

8. Customer Support .....................................................................................12

1. Package Content

Thank you for purchasing PLANET Layer 2 Managed Industrial Switch, ISW-

1022M or ISW-1033M series. Terms of “Managed Industrial Switch” means the

Switches mentioned titled in the cover page of this Quick installation guide, i.e.

ISW-1022M / ISW-1022MT / ISW-1022MPT / ISW-1022MP / ISW-1033MT.

Open the box of the Managed Industrial Switch and carefully unpack it. The box

should contain the following items:

The Managed Industrial Switch x 1

User’s Manual CD x 1

Quick Installation Guide x 1

RS232 cable (RJ-45 to DB9) x 1

Two Rack-mounting brackets with attachment screws x 1

If any item is found missing or damaged, please contact your local reseller for

replacement.

2. Requirements

Workstations of subscribers running Windows 98/ME, NT4.0, 2000/2003/XP, MAC

OS9 or later, Linux, UNIX or other platform compatible with TCP/IP protocols.

Workstation installed with Ethernet NIC (Network Card)

Serial Port connect (Terminal)

Above PC with COM Port (DB-9)

Ethernet Port connect

Network cables - Use standard network (UTP) cables with RJ45 connectors.

Above PC installed with WEB Browser and JAVA runtime environment Plug-in

Note

It is recommended to use Internet Explore 6.0 or above to access

Managed Industrial Switch.

3. Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of Managed Industrial

Switch is used for two DC redundant powers input. Please follow the steps below

to insert the power wire.

1. Insert positive / negative DC power wires into the contacts 1 and 2 for POWER

2, or 5 and 6 for POWER 1.

2. Tighten the wire-clamp screws for preventing the wires from loosing.

123456

Power 2 Power 1

- + - +

Note

The wire gauge for the terminal block should be in the range

between 12 ~ 24 AWG.

4. Terminal Setup

To congure the system, connect a serial cable to a COM port on a PC or notebook

computer and to RJ-45 type serial (console) port of the Managed Industrial Switch.

The console port of the Managed Industrial Switch is DCE already, so that you can

connect the console port directly through PC without the need of Null Modem.

PC / Workstation

with

Terminal emulation software

ISW Industrial Managed Switch

RJ-45 Type Serial Port

9600,8,n,1

RJ-45 to DB9 Rs-232

Cable

Serial Port

A terminal program is required to make the software connection to the ISW

Managed Industrial Switch. Windows’ Hyper Terminal program may be a good

choice. The Hyper Terminal can be accessed from the Start menu.

1. Click START, then Programs, Accessories and then Hyper Terminal.

2. When the following screen appears, make sure that the COM port should be

congured as:

Baud: 9600

Parity: None

Data bits: 8

Stop bits: 1

Flow Control: None

5. Logon to the Console

Once the terminal has connected to the device, power on the Managed Industrial

Switch, the terminal will display that it is running testing procedures.

Note

The following screen based on ISW-1022M, for ISW-1022MP and

ISW-1022MPT, the display will be the same to ISW-1022M.

Then, the following message asks the login user name and password. The factory

default user name and password as following and the login screen in Figure 5-1

appears.

User name: admin

Password: admin

Figure 5-1: Managed Industrial Switch Console Login screen

Note

1. For security reason, please change and memorize the new pass-

word after this first setup.

2. Only accept command in lowercase letter under console inter-

face.

6. Congure IP address

The Managed Industrial Switch is shipped with default IP address as following.

IP Address: 192.168.0.100

Subnet Mask: 255.255.255.0

To check the current IP address or modify a new IP address for the Managed

Industrial Switch, please use the procedures as follow:

nShow the current IP address

1. On “Switch>” prompt, enter “enable” to enter Privileged EXEC mode.

2. On “Switch #” prompt, enter “show ip”.

3. The screen displays the current IP address, Subnet Mask and Gateway. As show

in Figure 6-1.

Figure 6-1 Show IP information screen

n Congure IP address

4. On “Switch#” prompt, type “congure” to enter the conguration Mode.

5. On “Switch(cong)#” prompt, enter the following command and press

<Enter>. As show in Figure 6-2.

Switch(cong)# ip address 192.168.1.100 255.255.255.0 192.168.1.1

The previous command would apply the follow settings for the Managed Industrial

Switch.

IP: 192.168.1.100

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

Figure 6-2 Set IP address screen

6. Repeat Step 2 to check if the IP address is changed.

If the IP is successfully congured, the Managed Industrial Switch will apply the

new IP address setting immediately. You can access the Web interface of Managed

Industrial Switch through the new IP address.

Note

If you do not familiar with console command or the related param-

eter, enter “?” anytime in console to get the help description.

7. Start Web Management

The following shows how to start up the Web Management of the Managed

Industrial Switch. Note the Managed Industrial Switch is congured through an

Ethernet connection, please make sure the manager PC must be set on the same

IP subnet address.

For example, the default IP address of the Managed Industrial Switch is

192.168.0.100, then the manager PC should be set at 192.168.0.x (where x

is a number between 1 and 254, except 100), and the default subnet mask is

255.255.255.0.

PC / Workstation

with

IE Browser

ISW Managed Industrial Switch

IP Address:

192.168.0.x

RJ-45 / UTP Cable

IP Address:

192.168.0.100

Figure 7-1 IP Management Diagram

1. Use Internet Explorer 6.0 or above Web browser, enter IP address

http://192.168.0.100 (the factory-default IP address or that you have just

changed in console) to access the Web interface.

2. When the following dialog box appears, please enter the default user name

“admin” and password “admin” (or the username/password you have changed

via console). The login screen in Figure 7-2 appears.

Default User name: admin

Default Password: admin

This manual suits for next models

Table of contents

Other Planet Switch manuals

Planet

Planet PL-401E User manual

Planet

Planet DSP-1000 User manual

Planet

Planet LRP-822CS User manual

Planet

Planet WGS-4215-8P2S User manual

Planet

Planet KVM-800 User manual

Planet

Planet GSW-4804SF User manual

Planet

Planet MGSW-24160F User manual

Planet

Planet GS-5220-8UP2T2X User manual

Planet

Planet FGSW-2022VHP User manual

Planet

Planet IGS-4215 Series User manual

Planet

Planet FGSW-2620CS User manual

Planet

Planet FGSW-2402S User manual

Planet

Planet IAP-2000PE User manual

Planet

Planet SGSD-1022 User manual

Planet

Planet VC-820M User manual

Planet

Planet IKVM-8010 User manual

Planet

Planet IGS-6325 Series User manual

Planet

Planet WGS-4215 Series User manual

Planet

Planet GS-4210-24T4S User manual

Planet

Planet SGSW-2402 User manual

Planet

Planet GSD-802S User manual

Planet

Planet IPM-8221 User manual

Planet

Planet IFGS-1022HPT User manual

Planet

Planet VC-820M User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual