Planet Networking & Communication BSP-360 User manual

Industrial Renewable Energy

4-Port 10/100/1000T 802.3at PoE+

Managed Ethernet Switch

BSP-360

Quick Installation Guide

Safety Precautions

Please read the following before using:

1. All electrical work must be done in accordance with local, and/or international

electrical codes.

2. Before installing or using this device, read all instructions and cautionary

marking located in (or on) this guide, the controller, the batteries, PV (Photovol-

taic) array and any other device used.

3. To reduce the risk of short-circuits, use insulated tools when installing or working

with the inverter, the controller, the batteries, or any DC source (e.g., PV).

4. Remove all jewelry. This will greatly reduce the chance of accidental exposure to

live circuits.

5. The controller contains more than one live circuit (batteries and PV array).

Power may be present at more than one source.

6. This product contains no user serviceable parts. Do not attempt to repair this

unit unless fully qualied.

Table of Contents

1. Package Contents ....................................................................................... 4

2. Requirements ............................................................................................. 5

3. Hardware Introduction ................................................................................ 6

3.1 Front Panel ......................................................................................... 6

3.2 LED Indicators..................................................................................... 7

3.3 Upper Panel ........................................................................................ 8

4. Hardware Installation .................................................................................10

5. Web Management......................................................................................16

6. Customer Support .....................................................................................18

Appendix A: Recommended Use of the Connected Wires....................................19

Appendix B: Recommended Settings for Different Batteries ................................20

1. Package Contents

Thank you for purchasing PLANET Industrial Renewable Energy Managed PoE

Switch, BSP-360. Open the box of the BSP-360 and carefully unpack it. The box

should contain the following items:

1 x BSP-360 1 x Quick Installation Guide

1 x Wall Mounting Kit 1 x DIN Rail Kit 5 x RJ45 Dust Cap

If any of these are missing or damaged, please contact your dealer immediately. If

possible, retain the carton including the original packing materials to enable you to

repack the product in case there is a need to return it to us for repair.

2. Requirements

PLANET BSP-360 provides a remote login interface for management purposes. The

following equipment is necessary for further management:

Workstation is installed with Ethernet NIC (Network Interface Card)

Choice of Internet browsers includes Windows XP/2003, Vista, Windows 7,

Windows 8, Windows 10, MAC OS X, Linux, Fedora, Ubuntu or other platforms

compatible with TCP/IP protocols.

The above workstation is installed with Web browser and JAVA runtime envi-

ronment plug-in.

Ethernet Port connection

Use standard network (UTP) cables with RJ45 connectors.

PV and battery

Two 12V batteries connected in series.

The maximum operating voltage of PV is 45V.

Note

It is recommended to use Internet Explorer 8.0 or above to access

the BSP-360.

3. Hardware Introduction

3.1 Front Panel

The front panel of the BSP-360 consists of 5 auto-sensing 10/100/1000Mbps

Ethernet RJ45 ports and one USB interface. The LED Indicators are also located on

the RJ45 ports of the BSP-360.

V1+

Reset

DC Out

V2+

BSP-360

PWR Fault PV System

50W 100W 120W

PoE Power

Usage

ACTLNK

PoE In-use

Renewable Energy

Managed PoE+Switch

Figure 3-1 shows the front panel of BSP-360

Item Interface Description

1Port-1~Port-4 4 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports

with 802.af/at PoE+ injector function.

2Port-5

One 10/100/1000BASE-T RJ45 auto-MDI/MDI-X port.

Port-5 functions as WAN port when the operation

mode of BSP-360 is congured to “Gateway mode”

3USB Connect the USB storage to USB port and back up

the conguration le.

4Reset Button < 5 seconds: System reboot.

> 5 seconds: Factory default.

54-pin Terminal

Block

24V DC output connector.

The output voltage is the same as battery voltage.

Maximum voltage is clamped at 24V, 1A.

3.2 LED Indicators

System

LED Color Function

PWR Green On To indicate BSP-360 has power.

Fault Green

Slow

Blinks To indicate the PV is disconnected.

Fast

Blinks

To indicate the battery voltage is less than the

value for low voltage disconnection.

On To indicate bad battery, over-current or

short-circuit.

System Green

Slow

Blinks To indicate the system is “on”.

Fast

Blinks To indicate the battery is “charging”.

50W Green On To indicate the system consumes over 50-watt

PoE power budget.

100W Green On To indicate the system consumes over 100-watt

PoE power budget.

120W Green On To indicate the system consumes the total

120-watt PoE power budget.

PoE 10/100/1000BASE-T Interfaces (Port-1 to Port-4)

LED Color Function

LNK/

ACT Green Blinks To indicate the link through that port is

successfully established.

PoE Orange

Lights To indicate the port is providing DC in-line power.

Off To indicate the connected device is not a PoE

Powered Device (PD).

10/100/1000BASE-T Interfaces (Port-5)

LED Color Function

LNK/

ACT Green Blinks To indicate the link through that port is

successfully established.

3.3 Upper Panel

The upper panel of the BSP-360 consists of one terminal block connector with PV

and battery power inputs.

PV DC 24~45V Bat. DC 24V

Bat.

PV Alarm

+ +

1 2 3 4 5 6

Figure 3-2 Upper Panel

The input voltage range of each interface is shown as follows:

PV In Connector

24~45V DC

Solar PV

24~45V DC

PV DC 24~45V Bat. DC 24V

Bat.

PV Alarm

+ +

1 2 3 4 5 6

Figure 3-3 PV In Connector

Battery In/Out

24V DC

Battery

PV DC 24~45V Bat. DC 24V

Bat.

PV Alarm

+ +

1 2 3 4 5 6

24V DC

Figure 3-4 Battery In/Out

Note

The wire gauge for the terminal block should be in the range from

14 to 24 AWG.

DO Connectors

Level 0: -24V~2.1V (±0.1V)

Level 1: 2.1V~24V (±0.1V)

1 2 3 4 5 6

Load

5~24VDC

GND

Other manuals for BSP-360

Table of contents

Other Planet Networking & Communication Switch manuals