Pioneer AVIC-HD3 User manual

ENG/MASTER COVER 98 INST

êìäéÇéÑëíÇÖ èé ìëíÄçéÇäÖ

INSTALLATION MANUAL

AVIC-HD3—

English êÛÒÒÍËÈ

<CRD4324A/U> 1

01_CRD4324-A_inst_cover 08.1.28 2:52 PM Page 1

<CRD4324-A> 1

Important Safety Information

ABOUT THIS MANUAL

This manual explains how to install this navigation system in your vehicle. Operation of this navigation system

is explained in the separate operation manual or hardware manual for the navigation system. Before operating

this navigation system, be sure to read them.

PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR

NAVIGATION SYSTEM AND RETAIN THEM FOR FUTURE REFERENCE

Do not attempt to install or service your navigation system by yourself. Installation or

servicing of the navigation system by persons without training and experience in elec-

tronic equipment and automotive accessories may be dangerous and could expose you

to the risk of electric shock or other hazards.

1. Read this manual fully and carefully before installing your navigation system.

2. Keep this manual handy for future reference.

3. Pay close attention to all warnings in this manual and follow the instructions carefully.

4. This navigation system may in certain circumstances display erroneous information regarding the

position of your vehicle, the distance of objects shown on the screen, and compass directions. In addi-

tion, the system has certain limitations, including the inability to identify one-way streets, temporary

traffic restrictions and potentially unsafe driving areas. Please exercise your own judgement in the

light of actual driving conditions.

5. As with any accessory in your vehicle’s interior, the navigation system should not divert your atten-

tion from the safe operation of your vehicle. If you experience difficulty in operating the system or

reading the display, please make adjustments while safely parked.

6. Please remember to wear your seat belt at all times while operating your vehicle. If you are ever in an

accident, your injuries can be considerably more severe if your seat belt is not properly fastened.

7. In certain countries, laws may restrict the placement and use of navigation systems in your vehicle.

Please comply with all applicable laws and regulations in the installation and operation of your navi-

gation system.

ENG/MASTER 96

<CRD4324A/U> 2

02_CRD4324-A_inst_001_029_UK 08.1.28 2:56 PM Page 2

<CRD4324-A> 2

<CRD4324A/U> 3

English Español Deutsch Français Italiano Nederlands

Important Safety Information.................... 1

ABOUT THIS MANUAL.................................. 1

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING

YOUR NAVIGATION

SYSTEM AND RETAIN THEM

FOR FUTURE REFERENCE .................... 1

Connecting the System ............................ 3

Before installing this navigation system ............ 4

To prevent damage ............................................ 5

Parts supplied .................................................... 6

Connecting the system ...................................... 7

Connecting the power cord (1) .......................... 9

Connecting the power cord (2) ........................ 11

When connecting to separately sold power

amp .......................................................... 13

When connecting a rear view camera ............ 15

When connecting the external video component

.................................................................. 16

When connecting the external unit featuring video

source ........................................................16

When connecting the rear display ....................17

-When using a rear display connected to rear

video output

Installation ................................................ 18

To guard against electromagnetic

interference .............................................. 19

Before installing .............................................. 19

Installing this navigation system ...................... 20

-Installation notes

-Parts supplied

-Installation using the screw holes on the side

of the navigation unit

Installing the GPS aerial .................................. 23

-Installation notes

-Parts supplied

-When installing the aerial inside the vehicle

(on the rear shelf)

-When installing the aerial outside the vehicle

(on the body)

Installing the microphone..................................26

-Parts supplied

-Mounting on the sun visor

-Installation on the steering column

Adjusting the microphone angle ......................27

After Installing this Navigation System

.............................................................. 28

ENG/MASTER 96

Contents

02_CRD4324-A_inst_001_029_UK 08.1.28 2:56 PM Page 3

<CRD4324-A> 3

<CRD4324A/U> 4

ENG/MASTER 96

Connecting the System

Pioneer does not recommend that you install your navigation system yourself. We

recommend that only authorised Pioneer service personnel, who have special training

and experience in mobile electronics, set up and install this navigation system.

NEVER SERVICE THIS NAVIGATION SYSTEM YOURSELF. Installing or ser-

vicing this navigation system and its connecting cables may expose you to the risk of

electric shock or other hazards, and can cause damage to the navigation system that

is not covered by warranty.

• If you decide to perform the installation yourself, and have special training

and experience in the mobile electronics installations, please carefully follow

all of the steps in the Installation Manual.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare

wiring to remain exposed.

• Do not directly connect the yellow lead of this navigation system to the vehi-

cle battery. If the lead is directly connected to the battery, engine vibration

may eventually cause the insulation to fail at the point where the wire passes

from the passenger compartment into the engine compartment. If the yellow

lead’s insulation tears as a result of contact with metal parts, short-circuiting

can occur, resulting in considerable danger.

• It is extremely dangerous to allow the GPS aerial cable or microphone cable

to become wound around the steering column or gearstick. Be sure to install

this navigation system, its cables, and wiring away in such a way that they

will not obstruct or hinder driving.

• Make sure that the cables and wires are routed and secured so they will not

interfere with or become caught in any of the vehicle’s moving parts, espe-

cially the steering wheel, gearstick, handbrake, sliding seat tracks, doors, or

any of the vehicle’s controls.

02_CRD4324-A_inst_001_029_UK 08.1.28 2:56 PM Page 4

<CRD4324-A> 4

<CRD4324A/U> 5

English Español Deutsch Français Italiano Nederlands

ENG/MASTER 96

• Do not route wires where they will be exposed to high temperatures. If the

insulation heats up, wires may become damaged, resulting in a short circuit

or malfunction and permanent damage to the navigation system.

• Do not cut the GPS aerial cable to shorten it or use an extension to make it

longer. Altering the aerial cable could result in a short circuit or malfunc-

tion.

• Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse

resister or filter, etc.) may fail to work properly.

• Never feed power to other electronic products by cutting the insulation of the

power supply lead of the navigation system and tapping into the lead. The

current capacity of the lead will be exceeded, causing overheating.

• The black lead is earth. Please earth this lead separately from the earth of

high-current products such as power amps. Do not earth more than one

product together with the earth from another product. For example, you

must separately earth any amplifier unit away from the earth of this naviga-

tion system. Connecting earths together can cause a fire and/or damage the

products if their earths became detached.

Before installing this navigation system

• This navigation system is for vehicles with a 12-volt battery and negative earthing.

Check the battery voltage of your vehicle before installation.

• To avoid shorts in the electrical sys-

tem, be sure to disconnect the (–)

battery cable before beginning

installation.

02_CRD4324-A_inst_001_029_UK 08.1.28 2:56 PM Page 5

<CRD4324-A> 5

Connecting the System

To prevent damage

• When disconnecting a connector, pull the connector itself. Do not pull the lead, as you

may pull it out of the connector.

• This navigation system cannot be installed in a vehicle that does not have an ACC

(accessory) position on the ignition switch.

• When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse

holder.

• To avoid a short-circuit, cover the disconnected lead with insulating tape. Insulate the

unused speaker leads without fail. There is a possibility of a short-circuit if the leads are

not insulated.

• Attach the connectors of the same colour to the corresponding coloured port, i.e., blue

connector to the blue port, black to black, etc.

• Refer to the owner’s manual for details on connecting the power amp and other units,

then make connections accordingly.

• Since a unique BPTL circuit is employed, do not directly earth the ≠side of the speaker

lead or connect the ≠sides of the speaker leads together. Be sure to connect the ≠side

of the speaker lead to the ≠side of the speaker lead on this navigation system.

• If the RCA pin jack on this navigation system will not be used, do not remove the caps

attached to the end of the connector.

• Speakers connected to this navigation unit must be high-power with minimum rating of

50 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance

values other than those noted here may result in the speakers catching fire, emitting

smoke, or becoming damaged.

• When the ignition switch is turned on (ACC ON), a control signal is output through the

blue/white lead. Connect to an external power amp’s system remote control terminal

(max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even

if the audio source is switched off.

• When an external power amp is being used with this system, be sure not to connect the

blue lead to the amp’s power terminal. Likewise, do not connect the blue lead to the

power terminal of the auto aerial. Such connection could cause excessive current drain

and malfunction as well as damage to the auto aerial of the vehicle.

• When the “Auto ANT” mode is set to “Radio”, the vehicle’s aerial can be stowed or

turned off by following the instructions below.

– Change the source from radio (AM or FM) to another source

– Turn the source off

– Turn off the ignition switch (ACC OFF)

• If the “Auto ANT” mode is set to “Power”, the vehicle’s aerial can be stowed or turned

off only when the ignition switch is turned off (ACC OFF).

No ACC positionACC position

ENG/MASTER 96

<CRD4324A/U> 6

02_CRD4324-A_inst_001_029_UK 08.1.28 2:56 PM Page 6

<CRD4324-A> 6

<CRD4324A/U> 7

English Español Deutsch Français Italiano Nederlands

ENG/MASTER 96

Parts supplied

MicrophoneRCA connector 2

(CONNECTOR 2)

<☞

See Page 7, 12, 15, 17

RCA connector 1

(CONNECTOR 1)

<☞See Page 10, 13, 16>

GPS aerialExtension lead

(for speed signal)

Extension lead

(for reverse signal)

ConnectorPower cord

<☞See Page 9, 11, 15>

The navigation unit

02_CRD4324-A_inst_001_029_UK 08.1.28 2:56 PM Page 7

<CRD4324-A> 7

<CRD4324A/U> 8

Connecting the System

ENG/MASTER 96

Connecting the system

AV-BUS cable

(supplied with TV tuner)

IP-BUS cable

(supplied with TV tuner)

Black

Bluetooth unit (ND-BT1)

(Sold separately)

Aerial

jack

Vehicle

aerial

The navigation unit

RCA connector 2

20 cm

Red

Hide-away TV tuner

(e.g. GEX-P5700TVP)

(sold separately)

Light grey

GPS aerial

Blue

Not used.

Microphone input

Microphone

(supplied)

Blue

EXTENSION port

Not used.

4 m

Jack for Wired Remote

Control Adapters

(WIRED REMOTE INPUT)

Please see the Instruction

Manual for the Wired

Remote Control Adapters

(sold separately).

02_CRD4324-A_inst_001_029_UK 08.1.28 2:56 PM Page 8

<CRD4324-A> 8

ENG/MASTER 96

English Español Deutsch Français Italiano Nederlands

<CRD4324A/U> 9

Dock connector port

iPod with

Dock Connector

iPod adapter

(e.g. CD-IB100II)

(sold separately)

Black

IP-BUS cable

(supplied with iPod adapter)

Multi-CD player

(sold separately)

Blue

• To avoid the risk of accident and

the potential violation of applicable

laws, this navigation system should

never be used while the vehicle is

being driven except for navigation

purposes. Also Rear Displays should

not be in a location where it is a visi-

ble distraction to the driver.

• In some countries, the viewing of

images on a display inside a vehicle

even by persons other than the dri-

ver may be illegal. Where such reg-

ulations apply they must be obeyed

and this navigation system’s video

source or TV features should not be

used.

02_CRD4324-A_inst_001_029_UK 08.1.28 2:56 PM Page 9

<CRD4324-A> 9

Connecting the System

ENG/MASTER 96

<CRD4324A/U> 10

Connecting the power cord (1)

Connect leads of the same

colour to each other.

Cap (*1)

When not using this terminal,

do not remove the cap.

ISO connector

Fuse (10 A)

Yellow (*2)

To terminal always supplied

with power regardless of

ignition switch position.

Red (*4)

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Yellow (*3)

Back-up

(or accessory)

Red (*5)

Accessory

(or back-up)

Black (earth)

To vehicle (metal) body.

Orange/white

To lighting switch terminal.

Note:

In some vehicles, the ISO connector

may be divided into two. In this case,

be sure to connect to both connectors.

Note:

Depending on the kind of vehicle, the

function of *3 and *5 may be different.

In this case, be sure to connect *2 to *5

and *4 to *3.

Speaker leads

White: Front left +

White/black: Front left ≠

Grey: Front right +

Grey/black: Front right ≠

Green: Rear left +or Subwoofer +(*9)

Green/black: Rear left ≠or Subwoofer ≠(*9)

Violet: Rear right +or Subwoofer +(*9)

Violet/black: Rear right ≠or Subwoofer ≠(*9)

Yellow/black

If the vehicle can send a mute signal to this terminal,

the mute function can be activated on this navigation

system when the terminal is connected to *8.

Note:

When a subwoofer (*9) is connected to this naviga-

tion system instead of a rear speaker, change the

rear output setting in the Initial Setting. (Refer to

the operation manual.) The subwoofer output of this

navigation system is monaural.

When using a subwoofer of 70 W (2 Ω), be sure to

connect with violet and violet/black leads of this

navigation unit. Do not connect anything with green

and green/black leads.

02_CRD4324-A_inst_001_029_UK 08.1.28 2:56 PM Page 10

<CRD4324-A> 10

Other manuals for AVIC-HD3

Table of contents

Other Pioneer Car Navigation System manuals

Pioneer

Pioneer AVIC-Z110BT User manual

Pioneer

Pioneer AVIC-F20BT User manual

Pioneer

Pioneer AVIC-F88DAB User manual

Pioneer

Pioneer AVIC-EV01 User manual

Pioneer

Pioneer AVIC-N1 User manual

Pioneer

Pioneer AVIC-D1 User manual

Pioneer

Pioneer AVIC-F30BT Operating manual

Pioneer

Pioneer AVIC-HD3 User manual

Pioneer

Pioneer AVIC-F7200 User manual

Pioneer

Pioneer AVIC N2 - Navigation System With DVD player User manual

Pioneer

Pioneer AVIC-U310BT User manual

Pioneer

Pioneer AVIC-X1BT User manual

Pioneer

Pioneer AVIC-HD3II User manual

Pioneer

Pioneer AVIC-F60BT User manual

Pioneer

Pioneer AVIC-HD3 User manual

Pioneer

Pioneer AVIC-U220 User manual

Pioneer

Pioneer AVIC-EVO1-OC2-MTB User manual

Pioneer

Pioneer AVIC-F840BT User manual

Pioneer

Pioneer AVIC-D3 - Navigation System With DVD Player User manual

Pioneer

Pioneer AVIC U310BT - Navigation System With CD... User manual

Pioneer

Pioneer AVIC-Z720DAB User manual

Pioneer

Pioneer AVIC-F710BT User manual

Pioneer

Pioneer AVIC-HD3 User manual

Pioneer

Pioneer AVIC-D2 User manual

Popular Car Navigation System manuals by other brands

Clarion

Clarion Navigation In-Car Entertainment user guide

Rosen

Rosen DP-1001 owner's guide

Alpine

Alpine INE-W970HD installation manual

Skoda

Skoda AMUNDSEN+ operating instructions

Blaupunkt

Blaupunkt TravelPilot DX-N installation instructions

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... instruction manual

Kenwood

Kenwood DNN991HD quick start guide

AvMap

AvMap Geosat 2C user manual

Eonon

Eonon GE01B user manual

Nextar

Nextar M3-MX - Automotive GPS Receiver quick start guide

Furrion

Furrion NV2200 owner's manual

Mio

Mio MOOV 200-Series user manual

Prestigio

Prestigio GeoVision 5150 manual

Hummer

Hummer 2006 H3 manual

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Manuel d'utilisation

Garmin

Garmin StreetPilot c510 owner's manual

Garmin

Garmin nüvi 2200 owner's manual

Garmin

Garmin 2610/2650 owner's manual