Pintek DS-1010P User manual

100MHz With USB Interface

INSTRUCTION MANUAL

使用說明書

Digital Storage Oscilloscope

數位示波器

DS-1010P

TABLEOFCONTENTS

Safety Precautions……….…….…….………………………………………….04

Safety Terms and Symbols…………….….…………………….…………………….05

General Inspection…………………….…..…………………….…………………….06

Appearance and Dimension………….………………………….…………………….06

Adjust the Supporting Legs……………….……………………..…………………….07

Connect to AC Power Supply….…………….………………….…………………….08

Power-on Inspection…….………………….………………………………………….08

Connect the Probe……….…………………….……………………………………….08

Function Inspection…………………………….………………..………………….09

Probe Compensation……………………………….……………………………........10

Function Introduction of Front Panel…………….…………….....…………………11

Rear Panel Description…………………………….…………………………………..17

User Interface……………………………………….…………………………………..19

Using Security Lock…………………………….………………………………………21

Specifications…………………………….……………………………………………..22

Troubleshooting……………………….……………………………………………29

Maintenance and Cleaning……………….……………………………….…………..31

使用安全須知…………………………………..……………………….…………..33

安全術語和標記………………………………………………………….…………..34

一般性檢查……………………………………….………….……………………..35

外觀尺寸……………………………………….……………………………..…..35

調節支撐腳……………………………………….………………..………………...36

連接電源………………………………………………………….….…………….....37

開機檢查……………………………………….……………………….………...37

連接探頭……………………………………….………………………..…………....37

功能檢查……………………………………….…………………………….………..38

探頭補償……………………………………….………………………………….....39

前面板功能解說……………………………………….…………………………….40

後面板功能解說……………………………………….………………………..…46

用戶介面……………………………………….……………………………….......47

使用安全鎖……………………………………….…………………………………..49

技術規格……………………………..………….………………………….…..……50

故障處理………………………………………….…………………………………55

日常保養與清潔……………….…….……………………….…………………..……57

DS-1010P

100MHz Digital Storage Oscilloscope

Safety Precautions

Carefully read the following safety precautions to avoid personal injuries

and prevent damage to the instrument and any products connected to it.

To avoid potential hazards, please use the instrument as specified:

1. Only qualified technician should perform service procedures.

2. To Avoid Fire or Personal Injuries.

3. Use Proper Power Line:

Use only the special power line of the instrument which is approved by

local state.

4. Ground the Instrument:

The instrument grounds through the protective terra conductor of the

power line. To avoid electric shock, the ground conductor must be

connected to the earth. Make sure the instrument is grounded correctly

before connecting its input or output terminals.

5. Connect the Signal Wire Correctly:

The potential of the signal wire is equal to the earth, so do not connect

the signal wire to a high voltage. Do not touch the exposed contacts or

components.

6. Look Over All Terminals’ Ratings:

To avoid fire or electric shock, please look over all ratings and sign

instruction of the instrument. Before connecting the instrument, please

read the manual carefully to gain more information about the ratings.

7. Do not Operated with Suspected Failures:

If you suspect that there is a damage of the instrument, please let a

qualified service personnel check it.

8. Avoid Circuit or Components Exposed:

Do not touch exposed contacts or components when the power is on.

9. Do not Operated in Wet/Damp Conditions.

10. Do not Operated in an Explosive Atmosphere.

11. Keep the Surface of the Instrument Clean and Dry.

Do not store or leave the instrument in direct sunshine for long

periods of time.

To avoid damages to the instrument or probe, please do not leave

them in fog, liquid, or solvent.

Disconnect the instrument from all power sources, and then clean

it with a soft wet cloth.

Clean the loose dust on the outside of the instrument and probe

with a soft cloth. When cleaning the LCD, take care to avoid

scarifying it.

To avoid damages to the surface of the instrument and probe,

please do not use any corrosive liquid or chemical cleanser.

Make sure that the instrument is completely dry before restarting it

to avoid short circuits or personal injuries.

Safety Terms and Symbols

(1)Terms on the product. These terms may appear on the product:

DANGER:Indicates direct injuries or hazards that may happen.

WARNING:Indicates potential injuries or hazards that may

happen.

CAUTION:Indicates potential damages to the instrument or other

property that may happen

(2)Symbols on the product. These symbols may appear on the product:

Hazardous Voltage

Protective Earth Ground

Warning

Earth Ground

Power Switch

General Inspection

1. Inspect the shipping container:

Keep the damaged shipping container or cushioning material until the

contents of the shipment have been completely checked and the

instrument has passed both electrical and mechanical tests.

The consigner or carrier will be responsible for damages to the

instrument resulting from shipment. PINTEK would not provide free

maintenance or replacement.

2. Inspect the instrument:

If there are instruments found damaged, defective or failure in electrical

and mechanical tests, please contact PINTEK.

3. Check the accessories:

Please check the accessories according to the packing list. If the

accessories are incomplete or damaged, please contact your PINTEK

sales representative.

Appearance and Dimension

Front View:

Side View:

Adjust the Supporting Legs

Adjust the supporting legs properly to use them as stands to tilt the

oscilloscope upwards for stable placement as well as easier operation

and observation of the instrument.

Connect to AC Power Supply

The oscilloscope accept 100～240V, 45～440Hz AC power supply.

Please use the power cord provided as accessories to connect the

instrument to the power source as shown in the figure below.

Note: In want of replacing the fuse, please

return the instrument to the factory that

produced it to have it repaired by qualified

service personnel authorized by PINTEK.

Power-on Inspection

When the scope is energized, press the power key at the top of it to

turn it on. During the start-up progress, the instrument performs a

series of self-test items and you can hear the sound of relay switching.

After the self-test completes, the welcome interface displays

immediately.

Connect the Probe

Connect the probe:

(1) Connect the BNC terminal of the probe to one of the channel BNC

connector on the front panel.

(2) Connect the probe tip to the circuit point to be tested and the ground

alligator clip of the probe to the ground terminal of the circuit.

Power socket

Function Inspection

1. Press “DEFAULT SETUP” to restore the oscilloscope to its default

settings.

2. Connect the ground alligator clip of the probe to the Ground

Terminal on the front panel.

3. Use the probe to connect the CH1 Input Terminal and the

Compensation Signal Output Terminal on the front panel.

4. Press “AUTO”.

5. Observe waveforms on the screen. In normal condition, the display

should be several square waveforms as is shown below:

6. Test channel 2 in the same method. If the square waveforms do not

display like figure above, please perform “Probe Compensation”.

Note:

To avoid electric shock when using the probe, please firstly make sure

that the insulated wire of the probe is in good condition, and do not

touch the metallic part of the probe when it is connected to a high

voltage.

Probe Compensation

You should properly compensate the probe at first use of it.

Non-compensated or inadequate compensated probe may cause

inaccurate measurement. The following steps are about probe

compensation:

1. Perform step 1, 2, 3 and 4 of “Function Inspection”.

2. Check the displayed waveforms and compare them with the

following figure.

Under Compensated

Compensated Correctly

Over Compensated

3. Use a nonmetallic driver to adjust the low-frequency compensation

adjustment hole on the probe until the waveform changes to be

correct as the figure above.

Table of contents

Other Pintek Test Equipment manuals

Pintek

Pintek DP-40K User manual

Pintek

Pintek DP-40K User manual

Pintek

Pintek DP-16V User manual

Pintek

Pintek PS-XX0 Series User manual

Pintek

Pintek DP-50K User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual