Philips VSS7902/00T User manual
Electro Magnetic Compatibility (EMC)
This equipment complies with European rules for EMC according to
EN55013, EN55020 and EN50082-1.
Operation is subject to the following two conditions:
1 This device may not cause harmful interference.
2 This device must accept any interference received, including interference
that may cause undesired operation.
The equipment conforms with the EMC directive and low-voltage
directive.
This device complies to FCC rules under test conditions that included
use of system cables and connectors between system components. If you
have any problems, contact your dealer.
Warnings
Any unauthorized modification to this equipment may cause violation of
the FCC rules resulting in the revocation of the authorization to operate
the equipment.
To prevent fire or shock hazard, do not expose this accessory to rain or
moisture.
The exclamation mark within a triangle is intended to alert the
user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the
appliance.
2
Alarm/Action Box
Table of contents
Page
Introduction .................................................................................................................4
Installation....................................................................................................................6
Mounting the box
Installation and setting of an optional
Passive Infra-Red (PIR) detector
Location of the PIR
Installation of the PIR
PIR settings
Walk test LED
Pulse counter
System cable
Action output
Alarm input
Settings..........................................................................................................................13
Designating the box (CAMERA # switch)
Box number
Tamper switch active
Last in line switch
Double addressing error
English
g
Read these instructions, before putting your system in operation
English
3
g
Introduction
Thank you for buying this accessory for your observation system.
1 System monitor
2 Video recorder (VCR)
3 Slave monitor
4 Accessory boxes (0-2 per cable)
5 Interface box
6 System cameras
7 Non system cameras (CVBS)
8 Mains power adapter
The following items are included in this kit:
1 Alarm/action box
1 System cable (5m/15ft)
1 User manual
1 PIR unit (for version with PIR)
1 Cable (50 cm) for interconnection between alarm/action box and
PIR (for version with PIR)
Colour Observation Monitor
CL 66610005_005b.AI
4
6 6 7
2
talk action
menu _+next
auto view
Colour Observation system
Colour Observation Monitor
4 4
4
4
4
4
5
3
1
R
A
E
N
>
<
R
A
F
R
A
E
N
>
<
R
A
F
8
g
4
N.O. = Normally Open
N.C. = Normally Closed
The alarm/action box performs two distinct functions:
1 Action
This function, for example, opens a door remotely.
Pressing the action button of the system monitor activates a relay contact.
This contact (N.O., N.C.) can activate, for instance, a door opener.
Note that the action button only activates the action box designated to
the camera input whose picture is shown on the monitor screen.
2 Alarm
This function provides alarm inputs to the security system. All kinds of
detectors having a N.O. or N.C. contact are supported, for example:
•infrared detectors
•smoke detectors
•magnetic door/window contacts
When a detector triggers the alarm/action box, the system monitor
automatically switches to the camera input the alarm/action box is
designated to. The system monitor produces an alarm and activates its
alarm contact.
There are two versions of the alarm/action box: one with a Passive
InfraRed (PIR) motion detector and one without. The description in this
manual applies to both versions.
If the automatic camera sequence is active, it stops at the camera input in
question.
CL 66610005_511.AI
N.O.
N.C.
common
5
g
Installation
Remark: When the system configuration is altered, the system monitor needs to check
and memorize the configuration of the cameras and accessories connected to its inputs.
This is done automatically when the power is switched on. Use the power switch to
switch off. Operating the power save key is not sufficient.
If switching off is impracticable, use the auto install option of the system monitor's
install menu.
Mounting the box
1 Loosen the screw holding the cover and remove the cover.
2 Remove the circuit board 1.
3 Fasten the bottom plate of the box with two screws.
CL 66610005_501.AI
CL 66610005_502.AI
CL 66610005_504.AI
g
6
4 Fit the circuit board.
5 Now make the connections as described in section 'Action output'.
Remark: See section 'Installation and setting of an optional Passive
Infra-Red (PIR) detector', for installation and connection of an PIR-detector.
6IMPORTANT: Adjust the settings of the circuit board switches to
configure the box according to your system. See section 'settings'.
7 Fit the cover and secure the screw holding it.
Installation and setting of an optional Passive Infra-Red
(PIR) detector
Location of the PIR
The position of the PIR determines its view.
Select a location where an eventual burglar is most likely to be detected.
Place the sensor at a height of ± 2.2 m to accomplish the largest field of
view (see figure below).
Sensor range (lens position 0°)
Side view Top view
Be aware of the following before mounting the PIR:
•Avoid a location of the PIR near to radiators, heating/cooling ducts or
air conditioners.
•Do not point the sensor's field of view to windows subject to direct
sunlight or drafts.
•Do not block the sensor's field of view by placing large objects in its line
of sight (e.g. curtains, potted plants, furniture).
4M
13.15Ft 8M
26.3Ft 14M
46Ft
2.2M
7.2Ft
110
O
CL 76610006_001.AI
7
g
Installation of the PIR
1 Remove the fixation-screw (1) and open the housing by releasing the
locking latch (2). Both are located at the bottom of the unit.
2 Remove the circuit board by loosening the fixation-screw (1).
Warning: Never touch the face of the PYRO sensor (refer to lay out drawing
next page).
3 Knock out the desired mounting holes (1) and wiring holes (2) in the
bottom plate.
4 Thread the wires through the knocked out wiring hole(s).
5 Fasten the bottom plate with two screws, using the mounting holes.
6 Fit the circuit board.
CL 76610006_002.AI
3
1
2
CL 76610006_003.AI
1
1 2
g
8
Adjust lens position (0°, -5° or -10°) according to desired maximum
sensor range (see table below).
Remark: Do not use positions +5° or +10° as they do not apply to this PIR.
Sensor height Maximum sensor range (m) / Lens position (°)
0° -5° -10°
2.5 m 14 m 12.5 m 11 m
2.0 m 12 m 10.5 m 9.5 m
1.5 m 10 m 8.5 m 8 m
7 Make the interconnections between the PIR and the alarm/action box
with the cable supplied (see figure below).
1 Terminal block (for interconnection with alarm/action box)
2 Lens position (sensor range adjustment)
3 Jumper (walk test LED activated/deactivated)
4 Tamper switch
5 PYRO sensor
6 Jumper (1, 2 or 3 pulse count)
7 Locking latch
8 Terminal block in alarm/action box
CL 76610006_004.AI
5 87 6
2 14 3
GND
NC
+12V
+10
+5
0
-5
-10
+_NC
PIR
9
g
8 Adjust settings of walk test LED and/or pulse counter, if required.
See section 'PIR settings'.
9 Fit the front cover. Check if it is locked to the bottom side.
10 Fasten the fixation-screw.
Remark: The PIR detector will start detecting movement approximately 2 minutes
after mains power-on.
PIR settings
There are 2 jumpers to set the PIR to your own requirements:
•Walk test LED
•Pulse counter (1, 2 or 3)
See previous figure for the location of the jumpers.
Walk test LED
•jumper installed:
Walk test LED is activated. When the PIR sensor is triggered, the LED
will light.
•jumper not installed:
Walk test LED is deactivated.
Pulse counter
Set this jumper to select the number of times the sensor must be triggered
(1, 2 or 3 times) before an alarm is generated.
The following jumper settings are possible:
Remark: The PIR detector is equiped with a 'detection window'. In case of an
alarm, 15 seconds after the last movement has been detected, a new alarm can be
generated.
CL 76610006_005.AI
2X 3X1X
3P
2P
3P
2P
3P
2P
g
10
System cable
For the interconnections between the monitor, accessories and camera a
system cable is supplied. For optimum picture and sound quality you
should always use 4-wire dual twisted-pair cable when extending the
connection (max. 300m/900ft). The cable and plugs are available in the
hobby and professional trade. Pay attention that the connectors are fixed
to the cable corresponding to the figure below.
If the cable length between monitor and camera exeeds 200m/600ft after
an accessory is inserted in the line a mains power adapter should be used
to power the camera (see accessories).
Caution: The plugs used for the observation system have the same dimensions as
standard telephone plugs.
Never connect the security system with telephone equipment!
The two sockets for the system cable are interchangeable. One socket
connects the box to the system component previous in the cable, the
other to the next (if any).
CL 66610005_006.AI
5
4
3
2
4-5
2-3
5
4
3
2
4-5
2-3
5
4
3
2
5
4
3
2
11
g
Table of contents
Other Philips Accessories manuals
Philips
Philips DLA81000H User manual
Philips
Philips CRP393 User manual
Philips
Philips CRP147 User manual
Philips
Philips CRP154 User manual
Philips
Philips CPWBS154 Operator's manual
Philips
Philips DLA7575H User manual
Philips
Philips CRP363 User manual
Philips
Philips DLA91000H User manual
Philips
Philips SAC2590 User manual
Philips
Philips SVC2580 User manual
Philips
Philips LivingWhites 69165/31/PH User manual
Philips
Philips HD7003 User manual
Philips
Philips HF3520/97 User manual
Philips
Philips US2-P73020 User manual
Philips
Philips CRP329 User manual
Philips
Philips SVC1215/10 User manual
Philips
Philips 373414816 User manual
Philips
Philips SVC1212/10 User manual
Philips
Philips HF3520/70 User manual
Philips
Philips P-5562-B User manual
