Pelonis HC-0119A User manual

OWNER’S

MANUAL

PLEASE READ AND SAVE THESE INSTRUCTIONS

Model: HC-0119A

IMPORTANT INSTRUCTIONS

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce

the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.

If provided, use handles when moving this heater. Keep combustible materials, such

as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from

the front of the heater and keep them away from the sides and rear.

3. Extreme caution is necessary when any heater is used by or near children or invalids

and whenever the heater is left operating and unattended.

4. Always unplug heater when not in use.

5. Do not operate any heater with a damaged cord or plug or after the heater

malfunctions, has been dropped or damaged in any manner. Return heater to

authorized service facility for examination, electrical or mechanical adjustment, or

repair.

6. Do not use outdoors.

7. This heater is not intended for use in bathrooms, laundry areas and similar indoor

locations. Never locate heater where it may fall into bathtub or other water container.

8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar

coverings. Arrange cord away from traffic area and where it will not be tripped over.

9. To disconnect heater, first turn controls to off, then remove plug from outlet.

10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this

may cause an electric shock or fire, or damage the heater.

11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not

use on soft surfaces, like a bed, where openings may become blocked.

12. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where

gasoline, paint, or flammable liquids are used or stored.

13. Use this heater only as described in this manual. Any other use not recommended by

the manufacturer may cause fire, electric shock, or injury to persons.

14. Avoid the use of an extension cord because the extension cord may overheat and

cause a risk of fire. However, if you have to use an extension cord, the cord shall be

No. 14 AWG minimum size and rated not less than 1875 watts.

15. This heater draws 12.5 amps during operation. To prevent overloading a circuit, do

not plug the heater into a circuit that already has other appliances working.

16. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC

outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact

a qualified electrician to replace loose or worn outlet.

17. The output of this heater may vary and its temperature may become intense enough to

burn exposed skin. Use of this heater is not recommended for persons with reduced

sensitivity to heat or an inability to react to avoid burns.

18.“SAVE THESE INSTRUCTIONS”

Tower Ceramic

Heater

With Remote

UNPACKING AND SET-UP INSTRUCTIONS

Unpack your heater and remove the two half base from the package. Refer to the picture below:

1. Make sure the heater is unplugged and in the “OFF” position.

2. TURN THE HEATER UPSIDE DOWN. Un-fasten the four screws.

3. Fix the two half bases as shown.

4. Insert the four screws and screw them tightly.

5. Turn the heater upright. Your heater is now ready for use.

CAUTION: Risk of fire –Operate heater in upright position only (wheels on bottom, controls on

top). Any other position could create a hazardous situation.

OPERATION INSTRUCTIONS

IMPORTANT!

Your heater is equipped with a

polarized alternating current line

plug (a plug having one blade

wider than the other). This plug

will fit into the power outlet only

one way. This is a safety

feature. If you are unable to

insert the plug fully into the

outlet, try reversing the plug. If

the plug should still fail to fit,

contact your electrician to

replace your outlet. DO NOT

defeat the safety purpose of the

polarized plug.

Control

panel

Front LED

display

Carry handle

(behind)

Fig.1 Contr ol Panel Vi e w Fig.2 Remote C ontr ol

Panel View

Place the heater on a firm level surface free from obstructions, and at least 3 ft. away

from any wall and any other objects such as furniture, curtains, plants or combustible

material.

Plug the heater into a grounded 120V outlet; the buzzer sounds and the “A” Digital

Indicator indicate the room temperature. When the heater is on, every time you press

a key, the buzzer will sound.

Press POWER key, the operating mode is switched circularly in sequence of HI -LO -

FAN-OFF,

FAN: The Fan circulates room air only. The heating elements are “OFF”.

LOW: The Fan and heating elements operate at 900 Watts.

HIGH: The Fan and heating elements operate at 1500 Watts.

Temperature setting: When the heater is on (HI or LO), press “Up” or “Down” key

and the Digital Indicator will indicate the last set temperature (75 oFis the ex-factory

setting). You can now adjust your desired temperature by pressing “Up” or “Down”

key, the adjust range is 40-95 oF. If there is no operation in 5 second, the setting will

be saved and the Digital Indicator resume display the room temperature. Once the

temperature is set, the unit will select the operating mode based on the following 2

conditions of A and B:

A. If the setting temperature is higher than the room temperature, the heater

continues heating until the room temperature reaches the setting

temperature. Once the room temperature reaches your setting temperature,

the heater will stop heating. The heater will resume heating when the room

temperature is lower than the set temperature. The heater will cycle on and

off this way to maintain the setting temperature.

Fig.1 Control Panel Functions

Timer

Digital Indicator

Oscillation Switch

ADDITIONAL FEATURES

This heater has additional features:

•Dual LED display-Allow you to adjust the heater and check the set value at the same

time in a distance (Within16 ft of the heater), you can also check the status of the

heater easier.

•Convenient Carry Handle-Allow for easy maneuvering from room to room.

TROUBLESHOOTING

If your heater fails to operate, please follow these instructions:

•Ensure that your circuit breaker or fuse is working properly.

•Be sure the heater is plugged in and that the electrical outlet is working properly.

•Check for any obstruction. If you find any obstruction, turn the heater “OFF”. Unplug

the heater and wait a few minutes for it to cool down. Carefully remove the

obstruction. Plug the heater in and turn it on again by referring to the OPERATING

INSTRUCTIONS.

NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEND

YOUR HEATER TO AN AUTHORISED SERVICE CENTER FOR MAINTENCE.

PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF.

DOING SO MAY VOID THE WARRANTY AND COULD CAUSE DAMAGE OR

PERSONAL INJURY.

CLEANING AND STORAGE

It is recommended that the heater be cleaned at least one time during the operating season in

order to provide the optimum level of performance. ALWAYS TURN THE POWER SWITCH

OFF AND UNPLUG THE HEATER BEFORE CLEANING. Be sure to save the box for off-

season storage.

•Turn the heater “OFF”, unplug it and wait for the heater to cool down.

•Use a dry cloth to clean only external surfaces of the heater.

•Do not use any cleaning agents or detergents.

•Never immerse the heater in water.

•Pack the heater in the original carton and store it in a cool and dry place.

SPECIFICATIONS

Model No.: HC-0119A

Voltage: 120V, 60Hz

Current: Maximum continuous draw: 12.5 Amps.

Power: LO = 900 Watts, HI = 1500 Watts.

Tolerances on all specifications: Approximately +5%, -10%.

B. If the setting temperature is lower than or equal to the room temperature, the

temperature display will flash and the unit will stop heating. When the room

temperature falls down to less than the setting temperature, the unit will

resume heating. The heater will cycle on and off this way to maintain the

setting temperature.

Note: Every time you turn on the heater, the heater will heat forcedly for 2 minutes. After that the

heater will work based on the below instruction. And when the room temperature reaches the

setting temperature or the setting temperature is lower or equal to the room temperature, the

heating element will shut off immediately, but the fan motor will continue running for 10—30

seconds before shut off. This is a safety feature to protect the unit from being too hot.

Timer setting: This heater has an 8 hours On/Off timer. You can set an “On” timer

when the heater is standing by (plug in but not working) or you can set an “Off” timer

when the heater is working. For example, you can plug in the heater and set the timer

to turn the heater on after 3 hours, you can also set the timer to turn the heater off after

6 hours and a half when the heater is working.

Example for “On” Timer:

1. When the heater is plug in and not working, press “C” Timer, the “A” Digital Indicator will

display the last set value (0.0 is the ex-factory set). Press the “Up” or “Down” key to

choose your desired timer setting. The timer set increase or decrease half on hour every

time you press the “Up” or “Down” key and goes up and down from 0.0 to 8.0.

2. Press “Up” key 6 times until 3.0 is displayed, press “C” Timer again to confirm the set.

Now your heater is set to be turned on after 3 hours.

Example for “Off” Timer:

1. When the heater is working, press “C” Timer.

2. Press “Up” key 13 times or “Down” key 3 times until 6.5 is displayed, press “C” Timer

again to confirm the set.

Now your heater is set to be turned off after 6 hours and a half.

To disable the timer, adjust the set value of the timer to 0.0.

Note: Once the timer is set, the heater will work this way unless you unplug the heater. You have

to reset the timer every time you plug in your heater.

Remote control(Refer to Fig 2): This heater has a 6 keys remote with the

following function (See picture above) :

1. ON/OFF: Power switch key, used to turn off the heater when the heater is under

working.

2. OSC: Oscillation switch, used to enable the oscillation function by pressing once. To

disable the oscillation function, press the “OSC” key once more. This key is only valid

when the heater is under working (Hi, Low or Fan).

3. TIMER: Timer setting key, used to enable the timer setting or confirmed the setting

value.

4. MODE: Mode select key, used to switched the heater circularly in sequence of HI -LO –

FAN when the heater is on.

5. “+” and “-”: Value adjustment key, used to adjust the set value of the temperature or

the timer.

CAUTION: This heater includes an Overheat Protection System that shuts the unit off if it

overheats due to abnormal conditions. If this occurs turn the heater “OFF”, unplug it, and inspect

and remove any objects on or adjacent to the heater. Allow it to cool for a few minutes, plug it

back in, and resume normal operation.

SERVICE & SUPPORT

In the event of a warranty claim or if service is required for this heater, please contact us at

the following:

Toll Free: 866-876-4332

Email us at: MideaUSA@aol.com

For questions or comments, please write to:

2617 North Great Southwest Parkway

Grand Prairie, TX 75050, USA

For your records, staple your sales receipt to this manual and record the following:

DATE OF PURCHASE: _________________________________________________________________

PLACE OF PURCHASE: ________________________________________________________________

SERIAL NUMBER: _____________________________________________________________________

(STAPLE SALES RECEIPT HERE)

NOTE: PROOF OF PURCHASE IS REQUIRED FOR

ALL WARRANTY CLAIMS

ONE (1) YEAR LIMITED WARRANTY

•Please read all instructions before attempting to use this product.

•Please return the Warranty Registration card within fifteen (15) days from the date of

purchasing this product.

PELONIS warrants as limited herein to the original purchaser of retail that each new

Pelonis Tower Ceramic Heater, shall be free of defects in material and workmanship for a

period of one (1) year from the date of original purchase. This one (1) year warranty is

limited to the heating elements, motor, and electric control circuit board.

In the event of malfunctions or failure of your Pelonis Tower Ceramic Heater, simply deliver

or send the heater, postage prepaid along with PROOF OF PURCHASE, within the

warranty period of one (1) year, to PELONIS. PELONIS reserves the right to inspect the

claimed defective part or parts to determine if the defect or malfunction complaint is

covered by this warranty. PELONIS shall, within sixty (60) days after receipt of the product,

at its option, repair and/or replace the defective part or parts free of charge. This warranty

shall only cover defects arising from normal usage. PELONIS assumes no responsibility

whatsoever if the Tower Ceramic Heater should fail during the warranty period by reason

of:

•Misuse, negligence, physical damage or accidents.

•Lack of maintenance (see instructions for proper maintenance).

•Repair by any unauthorized party during the warranty period.

•Damage caused by connection to an improper input voltage (see specification

label on your heater).

PELONIS makes no further warranties or representations, express or implied except those

contained herein. No representative or dealer is authorized to assume any other liability

regarding the Tower Ceramic Heater. The duration of the implied warranty granted under

State law, including warranties of merchantability and fitness for particular purpose are

limited in duration should the duration of the express warranty grant it hereunder. Pelonis

USA shall in no event be liable for direct, indirect, special or consequential damages.

Some states do not allow limitations on how long an implied warranty lasts, and/or the

above limitations or exclusion may not apply to you. This warranty gives you specific legal

rights and you may have other rights which vary from state to state.

Other Pelonis Heater manuals

Pelonis

Pelonis HC-461 User manual

Pelonis

Pelonis NTK15A User manual

Pelonis

Pelonis HC-0155M User manual

Pelonis

Pelonis HO-0221 User manual

Pelonis

Pelonis NTY15-16LA User manual

Pelonis

Pelonis NF15-9BMB User manual

Pelonis

Pelonis HC-0113 User manual

Pelonis

Pelonis PHTA8AWB User manual

Pelonis

Pelonis PHT30D7BBC User manual

Pelonis

Pelonis PHTPU1501 User manual

Pelonis

Pelonis PTH21S4BRB User manual

Pelonis

Pelonis HF-0055 User manual

Pelonis

Pelonis HC-0125D User manual

Pelonis

Pelonis PSHF2022EOC User manual

Pelonis

Pelonis Safe-T FURNACE HC-445 User manual

Pelonis

Pelonis PSH17PF2HDB User manual

Pelonis

Pelonis HF-0021 User manual

Pelonis

Pelonis HC-0113 User manual

Pelonis

Pelonis PHTPU1501WC User manual

Pelonis

Pelonis PFH15A2BGB User manual

Pelonis

Pelonis HF-0019 User manual

Pelonis

Pelonis PSH750S User manual

Pelonis

Pelonis HO-0203D User manual

Pelonis

Pelonis HO-202C User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide