Peerless-AV HT642-004 Guide

Model: HT642-004

Installation and Assembly:

Tilt Wall Mount with Component Storage Capability

Max Load Capacity: 80 lb (29 kg)

ISSUED: 09-21-11 SHEET #: 125-9245-1

Note: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

• studnder("edgetoedge"studnderisrecommended)

• phillips screwdriver

• drillwith1/4"and5/32"drillbits

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall................................................................................................................................................4

Installation to Metal Stud Wall ................................................................................................................................................5

Installation to Solid Concrete and Cinder Block Wall .............................................................................................................6

Attaching Adapter Brackets to Screen........................................................................................................................ 7 AND 8

Attaching Mounting Bracket Using Hook On Option...............................................................................................................9

Attaching Mounting Bracket Using Tilt Option ..................................................................................................................... 10

• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please

callPeerlesscustomerserviceat1-800-729-0307.

• Thisproductshouldonlybeinstalledbyaqualiedprofessional.

• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-

ware and components.

• NeverexceedtheMaximumLoadCapacityof80 lb (29 kg).

• Ifmountingtowoodwallstuds,makesurethatmountingscrewsareanchoredintothecenterofthestuds.Useof

an"edgetoedge"studnderishighlyrecommended.

• Alwaysuseanassistantormechanicalliftingequipmenttosafelyliftandpositionequipment.

• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding

power.

• Thisproductwasdesignedandintendedtobemountedtothefollowingsupportingsurfacescheckedbelowwith

thehardwareincludedinthisproductasspeciedintheinstallationsheet.Tomountthisproducttoanalternative

supporting surface, contact Peerless customer care at 1-800-865-2112.

• Thisproductwasdesignedtobeinstalledonthefollowingwallconstructiononly;

WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED

x Wood Stud None

xWood Beam None

xSolid Concrete None

xCinder Block None

xMetal Stud None

Brick Contact Customer Service

Other or unsure? Contact Customer Service

WARNING

3 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1

Some parts may appear slightly different than illustrated.

Before you start make sure all parts listed are included with your product.

CD E

H I J K

LMNO

Description Qty. Part #

Arightadapterbracket 1 201-1943

Bleft adapter bracket 1 201-1942

Cwall plate 1 201-1940

DM4 x 12 mm socket serrated washer head screw 4 510-1079

EM6 x 16 mm socket pin screw 4 520-1132

Ftoggler 4 560-9708

G18"long4mmallenwrench 1 560-1727

H1/4-20x23/4"socketpinscrew 4 520-1580

I#14x2.5woodscrew 4 5S1-015-C03

JM5 x 12 mm socket pin serrated washer head screw 6 510-1064

Kconcreteanchor 4 590-0320

L# 8 washer 4 540-1001

Mdual lock 4 600-1009

NM8 x 10 mm socket pin screw 4 520-1706

Onylonshoulderwasher 4 590-2233

PARTS LIST

4 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1

Installation to Wood Stud Walls

Useastudndertolocatetheedgesofthestud.Useofanedge-to-edgestudnderishighlyrecommended.

Based on its edges, draw a vertical line down the stud's center. Place wall plate (C) on wall as a template. Mark

thecenterofthefourmountingholes.Drillfour5/32"(4mm)dia.holes2-1/2"(65mm)deep.Securewallplate(C)

towoodstudusingfour#14x2-1/2"woodscrews(I) as shown. Skip to Step 2 page 7

• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandall

attached hardware and components.

• Tightenwoodscrewssothatwallplateisrmlyattached,butdonotovertighten.Overtighteningcandamagethe

screws, greatly reducing their holding power.

• Nevertighteninexcessof80in.•lb(9N.M.).

• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan"edgetoedge"studnder

is highly recommended.

• Hardwareprovidedisforattachmentofmountthroughstandardthicknessdrywallorplasterintowoodstuds.Install-

ers are responsible to provide hardware for other types of mounting situations.

WARNING

5 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1

Installation to Metal Stud Walls

Rotate toggler (F)

clockwise to wedge it

against inside walls

of metal stud.

Push into hole.

Pivot end of

toggler (F).

Slide plastic cap

forward while pulling

backrmlyonring.

Break off excess.

FOR METAL STUD WALLS ONLY:Drillfour1/2"

(13mm)dia.holesthroughdrywallandstudsatlo-

cations corresponding to wall plate. Insert togglers

(F) as shown below...

Skip to Step 2 page 7

Align wall plate with

hole in wall and

fasten with 1/4-20 x 2

3/4"screw(H) using

18"long4mmallen

wrench (G).

wall plate

• Productmustbemountedthroughdrywallthathasa

minimumthicknessof1/2"andintometalstuds,26

gauge or heavier.

• Makesurethattogglersareanchoredintothecenter

ofthestudsasshowningure1.Theuseofan

"edgetoedge"studnderishighlyrecommended.

WARNING

STUD

1-1

1-2

1-3

1-4

1-5

1-6

Skip to Step 2

g.1

g1.4

CINDER BLOCK

SOLID CONCRETE

6 of 10 ISSUED: 09-21-11 SHEET #: 125-9245-1

Installation to Solid Concrete or Cinder Block

• WheninstallingPeerlesswallmountsoncinderblock,verifythatyouhaveaminimumof1-3/8"(35mm)ofactual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

inasolidpartoftheblock,generally1"(25mm)minimumfromthesideoftheblock.CinderblockmustmeetASTM

C-90specications.Itissuggestedthatastandardelectricdrillonslowsettingisusedtodrilltheholeinsteadofa

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concretemustbe2000psidensityminimum.Lighterdensityconcretemaynotholdconcreteanchor.

• Makesurethatthewallwillsafelysupportfourtimesthecombinedloadoftheequipmentandallattachedhardware

and components.

WARNING

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall

plaster/

drywall

concrete concrete

Drill holes and insert anchors (K).

Place plate (C) over anchors (K) and secure with screws (I).

Tighten all fasteners.

concrete

surface

• Tightenscrewssothatwallplateisrmlyattached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Nevertighteninexcessof80in.•lb(9N.M.).

• Alwaysattachconcreteexpansionanchorsdirectly

to load-bearing concrete.

• Neverattachconcreteexpansionanchorsto

concrete covered with plaster, drywall, or other

nishingmaterial.Ifmountingtoconcretesurfaces

coveredwithanishingsurfaceisunavoidable(not

evaluatedbyUL),thenishingsurfacemustbe

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when

tightening screws. If plaster/drywall is thicker than

5/8"(16mm),customfastenersmustbesupplied

by installer (not evaluated by UL).

WARNING

Make sure that wall plate (C) is level, use it as a

template to mark four mounting holes. The top mounting

holeshouldbe2.5"(64mm)abovethedesiredscreen

centerasshowningure1.1onpage4.Drillfour5/16"

(8mm)dia.holestoaminimumdepthof2.5"(64mm).

Insert anchors (K)inholesushwithwallasshown

(right). Place wall plate over anchors and secure with

#14x2.5"screws(I). Level, then tighten all fasteners.

7 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1

BACK OF DISPLAY

200 mm x 100 mm HOLE

PATTERN SHOWN ABOVE

7.87"

(200mm)

.98"

(25mm)

7.87"

(200mm)

BACK OF DISPLAY

MOUNTING HOLE LOCATIONS

DISPLAY

Attaching Adapter Brackets to Display

DETAIL 1

Using information provided in detail 1 secure adapter brackets (A and B) to back of display using four

M4 x 12 mm socket pin screws (D), with #8 washers (C) using18"long4mmallenwrench(G) as shown below.

NOTE: Make sure that screws are centered in hole in adapter brackets.

Skiptostep3

Attaching Adapter Brackets using VESA 200 x 100 Mounting Pattern

8 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1

BACK OF DISPLAY

E or N

NOTE: When using M6 x 16

socket pin screw (E), you

must use nylon washer (O).

MOUNTING HOLE LOCATIONS

DISPLAY

Using information provided in detail 1 secure two adapter brackets (A and B) to back of display with four M6 x 16

mm socket pin screws (E) and nylon shoulder washers (O), or four M8 x 10 mm socket pin screws (N) using18"

long 4 mm allen wrench (G).

NOTE: Make sure that screws are centered in hole in adapter brackets.

Attach dual lock (M) to back of adapter brackets (A and B) as shown below.

Attach component to dual lock as shown.

COMPONENT

NOTE: MAKE SURE THAT

COMPONENT CABLES

RUN AS SHOWN

Attaching Component to Adapter Brackets

Attaching Adapter Brackets using VESA 200 x 200 Mounting Pattern

9 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1

MOUNTING SURFACE

NOT SHOWN FOR CLARITY

Position slots of adapter plates (A and B) onto the

four M5 x 12 mm serrated washer head socket pin

screws (J) attached to wall plate (C).

To secure wall plate (C) to adapter plates (A and B), attach two M5 x 12 mm serrated washer head socket pin

screws (J) through the slots on the sides of wall plate (C) and threaded holes of adapter plates (A and B). Tighten

with the 4 mm security allen wrench (G).

Attach four M5 x 12 mm serrated washer head

socket pin screws (J) to the holes on the sides of

wall plate (C) using the 4mm security allen

wrench (G)provided.

Attaching Mounting Bracket Using Hook On Option

4-1

A and B

SLOT J

4-2

BOTTOM OF DISPLAY J

10 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1

Attach two M5 x 12 mm serrated washer head

socket pin screws (J) to the bottom holes on the

sides of wall plate (C) using the 4mm security allen

wrench (G)provided.

Position slots of adapter brackets (A and B) onto

the two M5 x 12 mm serrated washer head socket

pin screws (J) attached to wall plate (C).

44-1

A and B

SLOT

Attaching Mounting Bracket Using Tilt Option

To secure wall plate (C) to adapter plates (A and B), adjust tilt as desired and attach two M5 x 12 mm serrated

washer head socket pin screws (J) into the slots on the sides of wall plate (A) and threaded inserts of adapter

brackets (A and B). Tighten with the 4 mm security allen wrench (G).

4-2

MOUNTING SURFACE

NOT SHOWN FOR CLARITY

BOTTOM OF DISPLAY

All other brand and product names are trademarks or registered trademarks of their respective owners.

Table of contents

Other peerless-AV Rack & Stand manuals

peerless-AV

peerless-AV ACC310VWC4 User manual

peerless-AV

peerless-AV SMARTMOUNT Series Instruction manual

peerless-AV

peerless-AV SF650-S User manual

peerless-AV

peerless-AV KOL547-XTR User manual

peerless-AV

peerless-AV SR598ML3E User manual

peerless-AV

peerless-AV DS-LEDKFS Kitted+ Free Standing User manual

peerless-AV

peerless-AV MOD-FPSKIT100 User manual

peerless-AV

peerless-AV SmartMountXT STX660P User manual

peerless-AV

peerless-AV YBA4X4 User manual

peerless-AV

peerless-AV SMARTMOUNT XT SFX645 User manual

peerless-AV

peerless-AV ST660-S User manual

peerless-AV

peerless-AV WMJ018 User manual

peerless-AV

peerless-AV PLCM-1 User manual

peerless-AV

peerless-AV IRTO49-200 User manual

peerless-AV

peerless-AV SMARTMOUNT SF630-AB User manual

peerless-AV

peerless-AV DS-LED27BDL-6X6 User manual

peerless-AV

peerless-AV Mobile Videowall Trolley PDVWM 3x3 46 55 L Guide

peerless-AV

peerless-AV YBP100 User manual

peerless-AV

peerless-AV SMARTMOUNT SA724P User manual

peerless-AV

peerless-AV PSMU-PRS Guide

peerless-AV

peerless-AV PRGS-UNV User manual

peerless-AV

peerless-AV SR560-HUB2 User manual

peerless-AV

peerless-AV SR560G User manual

peerless-AV

peerless-AV PRS-EXA Guide

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 

peerless-AV HT642-004 Guide

Popular Rack & Stand manuals by other brands