Peavey SA 4200 User manual

Other manuals for SA 4200

1

Other Peavey Amplifier manuals

Popular Amplifier manuals by other brands

ASTRO

ASTRO HVO V40 P operating manual

Marantz

Marantz SUPERSCOPE BLA-545 Service data

NAD

NAD CI980 Quick setup guide

Technics

Technics SE-CH770 Service manual

Harman Kardon

Harman Kardon HK6300 instruction manual

NAD

NAD T975 owner's manual

McIntosh

McIntosh MA6850 Brochure & specs

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N manual

Viatron

Viatron Autrix Technical manual

GME

GME GA9800 instruction manual

Atlas

Atlas CP700 Specification sheet

Roland

Roland KC-1000 owner's manual

Pyle

Pyle PFMRA350BW user manual

Advantage

Advantage S-250 manual

IRT Electronics

IRT Electronics DVA-3007 manual

Dimavery

Dimavery BA-100 Series user manual

Sony

Sony XM-S400D operating instructions

Schertler

Schertler ROY X quick guide

SA-4200 SPECIFICATIONS

SPECIFICATION LOW Z MODE 70 VOLT MODE

Rated Power (all channels driven)

Dual-Dual Mono & Parallel Modes

4 Ohms 200 Watts −

8 Ohms 130 Watts −

70 Volts −200 Watts

Minimum Load Impedance 4 Ohms 25 Ohms

Bridged Mode (Ch A & B)

8 Ohms 400 Watts −

16 Ohms 260 Watts −

140 Volts −400 Watts

Minimum Load Impedance 8 Ohms 50 Ohms

Frequency Response

+0, -1dB @ 1Watt <10Hz −35kHz 80Hz −30kHz

+0, -3dB @ full power 18Hz −30kHz 60Hz −15kHz

with 60Hz Low-Cut engaged

THD

at rated power, 1kHz <0.05% <0.05%

IMD (SMPTE) <0.10% <0.10%

Damping Factor >140 (8 Ohms) >400

Input CMRR -60 dB typ -60 dB typ

Voltage Gain ×20 (26dB) typ ×50 (34dB) typ

Input Sensitivity 1.42V (4 Ohms) 1.42V

1.62V (8 Ohms)

Input Impedance 20K Ohms balanced 20K Ohms balanced

10K Ohms unbalanced 10K Ohms unbalanced

Noise and Hum below rated output

delay channels (C & D) bypassed;

22Hz–22kHz BW -95 dB -95 dB

C & D delay active

A-weighted -88 dB -88dB

Current Consumption Multiply currents by 0.5 for 230V units.

Rated power 15.5 A (4 Ohms) 13.7 A

10.2 A (8 Ohms)

1/

3rated power 9.8 A (4 Ohms) 8.7 A

6.4 A (8 Ohms)

⅛rated power 6.6 A (4 Ohms) 5.9 A

4.2 A (8 Ohms)

Idle 0.5 A 0.9 A

Thermal Emission

1/

3power 3110 BTU/hr (4 Ohms) 2655 BTU/hr

2035 BTU/hr (8 Ohms)

⅛power 2365 BTU/hr (4 Ohms) 2080 BTU/hr

1500 BTU/hr (8 Ohms)

Controls

Front: 4 channel input signal attenuators, AC switch

Rear: 2 output mode switches; Ch A & B bridge switch; HPF switches;

AUTODELAY™ bypass switches; AUTODELAY setup switches

Indicator LEDs

Front: 4 Clip, 4 Signal, 1 Power

Rear: AUTODELAY setup

Protection

Over-Temperature, DC, turn on/off transients, subsonic, incorrect load, short-circuit

Connectors

Input: Four female XLRs - LINE INPUTS

One female XLR - TEST MICROPHONE

Output: Two 4-position barrier strips - SPEAKER OUTPUTS

One male XLR - REFERENCE OUTPUT

Construction

16 gauge steel reinforced with 12 gauge rack ears

Dimensions

Height: 3.50” (8.84 cm) 2 EIA rack spaces

Width, front: 19.00” (48.26 cm)

Width, rear: 17.00” (43.18 cm)

Overall depth: 17.05” (43.31 cm)

Mounting depth: 16.63” (42.24 cm) behind front rack ears

Weight

40 lbs (18.1 kg)

Power Requirements

100, 120, 230-240 Vac, 50-60 Hz

1200 Watts

Test Conditions

120Vac, 60Hz line input voltage maintained

All channels operating unless otherwise noted

Due to our efforts for constant improvements, features and

specifications listed herein are subject to change without notice.