Patton electronics SMARTNODE 1200 User manual

SmartNode™ Model 1200, 1400 & 4552

VoIP Gateway Routers

Quick Start Guide

Document Number: 13211U7-001 Rev. A

Part Number: 07MSWGUI-QS

Revised: October 31, 2005

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

SmartWare GUI Quick Start Guide

1.0 Power up the SmartNode

Connect the SmartNode to a power source using the included power supply and cable.

When the

Power

LED stops blinking and remains lit, the SmartNode is ready to conﬁgure.

2.0 Set your PC to DHCP

• The SmartNode contains no user serviceable parts. The equipment

shall be returned to Patton Electronics for repairs, or repaired by

qualiﬁed service personnel.

• Mains Voltage: Do not open the case when the power cord is con-

nected. For systems without a power switch, line voltages are

present within the power supply when the power cord is connected.

The mains outlet that is utilized to power the SmartNode router shall

be within 10 feet (3 meters) of the device, shall be easily accessible,

and protected by a circuit breaker

• The smartNode is not shipped with power cables. For AC powered

units, ensure that the power cable used meets all applicable stan-

dards for the country in which it is to be installed, and that it is con-

nected to a wall outlet which has earth ground.

• Hazardous network voltages are present in WAN ports regardless of

whether power to the SmartNode is ON or OFF. To avoid electric

shock, use caution when near WAN ports. when detaching the cables,

detach the end away from the SmartNode ﬁrst.

• Do not work on the system or connect or disconnect cables during

periods of lightning activity.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, ﬂam-

mability, and mechanical serviceability.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, ﬂam-

mability, and mechanical serviceability.

WARNING

CAUTION

SmartWare GUI Quick Start Guide

This guide will allow you to quickly access the conﬁguration interface of a SmartNode and give an overview of

the different elements you can or need to conﬁgure. For detailed information on all conﬁguration parameters

refer to the SmartWare software conﬁguration guide.

The SmartNode has a built in DHCP Server which allows an automatic IP connection with a connected PC. To pre-

pare the connection you need to conﬁgure the PC to use DHCP. The following paragraphs show how to do this on

Windows. For other operating systems refer to the operating instructions of the PC.

Right-click on

My Network Places

and select

Properties

in the context menu (see

ﬁgure 1

Figure 1.

Displaying the Network Connections window

Figure 2.

Displaying the Internet Properties (TCP/IP) Properties window

SmartWare GUI Quick Start Guide

Double-click on

Local Area Connection

and click on

Properties

to open the

Internet Protocol (TCP/IP)

Properties

window (see

ﬁgure 2

Select

Obtain an IP address automatically

and

Obtain DNS server address automatically

options.

Click

to save changes and close the properties windows.

3.0 Connect the PC to the SmartNode LAN Port

Now use the included Ethernet cable to connect the conﬁgured PC to the SmartNode. The factory default conﬁg-

uration of the SmartNode deﬁnes Ethernet port 0/1 as the LAN port.

Note

Most SmartNode Ethernet ports are Auto-MDIX which means that you can use a standard straight-wired

Ethernet cable to connect to the PC or a hub/switch.

Figure 3.

Connecting the SmartNode to the network

Note

As an alternative, you can connect to the console port (available on most models). Refer to the appro-

priate “Getting Started Guide” for detailed instructions on how to access the command line interface

(CLI) through the console port.

3.1 Open the Conﬁguration Interface

Once IP connectivity is established, use a web browser to get access to the SmartNode conﬁguration inter-

face. Enter “smart.node” in the address bar to get started (see

ﬁgure 4

Figure 4.

Using a web browser to access the SmartNode conﬁguration interface

Model Connect to port

SN1200/1400

ETH 0/1, use crossover cable or hub

SN4552

ETH 0/1 any one of the 4 ports, Auto-MDIX

LAN (ETH 0/1)

Network

interface PC

LAN

Internet or

WAN (optional)

WAN

(ETH 0/0)

SmartWare GUI Quick Start Guide

The subsequent pop-up window asks you for the login credentials (see

ﬁgure 5

). The factory default

User Name:

administrator

Password: There is no password, leave this ﬁeld empty

Figure 5.

Click

4.0 Get Started

After successful login you get to the SmartNode home page, and you can conﬁgure your device. You will be pre-

sented the following home page, which contains buttons to store the current conﬁguration state, reload the

device and restore to factory defaults. The home page also shows some system information. You can always go

back to the home page by clicking

Home

in the navigation bar.

SmartWare GUI Quick Start Guide

The GUI consists of the following main elements (see

ﬁgure 6

•

The “Navigation Bar” on the left edge presents you with a menu listing giving access to the various conﬁgura-

tion and status pages of the SmartNode.

•

At the top of the page you see the “Current System Path” which displays the location and element currently

presented in the main area.

•

The rest of the page displays the conﬁguration and status information for the different features of

the SmartNode.

Figure 6.

Main GUI elements

During the whole conﬁguration process, all your changes are only applied—that is,

saved in volatile memory (RAM). To store the settings in non-volatile memory (i.e.

make them survive power failure or manual reload), return to the home page and

press the

Save Current Conﬁguration

button.

Navigation

bar

Configuration and status tabs

Current

system path

IMPORTANT

SmartWare GUI Quick Start Guide

5.0 Access the Internet

Connect an Ethernet cable from the WAN port on the SmartNode to the upstream WAN Internet connection.

Begin the conﬁguration for Internet access with the WAN page.

Figure 7.

WAN page

5.1 Connecting a PC and logging in

Here

are some special hints you may use when conﬁguring your SmartNode:

There are three different conﬁguration options for the WAN Internet connection (see

ﬁgure 7

•

DHCP (client—factory default).

The SmartNode’s WAN port has a DHCP client enabled that uses an estab-

lished Internet connection to get the Internet connectivity parameters (IP address, default gateway) automatically

For each box containing an “Apply” button, ﬁll in the required ﬁelds and press “apply” once. The settings are

applied immediately after the button is pressed. If there are several boxes with an “Apply” button on one

page, ﬁll in the information per box and press the button for each box separately. This saves the new conﬁg-

uration parameters in volatile memory (RAM) only.

The “alert” symbol shows you that somewhere a user input is missing for correct functionality. In the case of

the present WAN page, you can ignore them, because the respective title bullet (“PPP over Ethernet”) is not

selected.

The “info” symbol denotes hints to ease conﬁguration or to avoid pitfalls. Read them whenever you

encounter them!

SmartWare GUI Quick Start Guide

from a DHCP server. Use this option when connecting the SmartNode to a DSL router, a cable modem, or to a

company LAN (with a DHCP server). This is the factory default conﬁguration so no conﬁguration is required, only

the LAN and WAN Ethernet connections should be made to access the Internet immediately.

•

PPPoE.

The SmartNode establishes the connection with the Internet using PPPoE. This is most commonly

used when the SmartNode is connected to a DSL

bridge

, or a DSL router that is conﬁgured in

bridge

mode

(most routers are capable of this).

Enter the DSL credentials (username and password) on the SmartNode and click on the

Apply

button.

•

ser Deﬁned Address.

The SmartNode uses an existing internet connection which does not provide an

upstream DHCP server. In this case, you need to set the IP address, subnet mask, default gateway and DNS

servers manually.

–

IP Address

—The IP address of the WAN Ethernet port.

–

IP Mask—

The mask for the WAN port’s IP address.

Click on the

Apply

icon to apply the new conﬁguration.

–

Default Gateway

—This is the IP address of the upstream router. Click on the

Apply

icon to apply the

new conﬁguration.

–

DNS/DynDNS

—In the Conﬁguration Menu, go to DNS/DynDNS. Enter the IP addresses of the DNS

servers and

Apply

the new settings.

Figure 7 on page 7 shows the third case—

User Deﬁned Address

conﬁguration of connectivity parameters.

In this example the SmartNode’s WAN IP address is 172.16.44.55 with an IP Mask of 255.255.255.0. The

Default Gateway is 172.16.44.1.

Note

Be sure to return to the

Home

conﬁguration page to save the new conﬁguration in non-volatile memory.

6.0 Additional Information

Refer to the

SmartNode Series SmartWare Software Conﬁguration Guide

and the

SmartNode Getting Started Guide

located on the CD-ROM shipped with your SmartNode device and available online at www.patton.com/manuals.

For detailed information about:

•

Installing, conﬁguring, operating, and troubleshooting.

•

Warranty, trademark & compliance

The “advanced GUI” leads you to the full universe of SmartNode conﬁguration parameters. There

are many more things that can be conﬁgured than you are presented on the “basic GUI” pages

you see when the system starts. Be aware that conﬁguration is quite a bit more complicated and

requires some know-how about VoIP and the SmartNode conﬁguration concepts. We recommend

familiarizing yourself with the

SmartWare Software Conﬁguration Guide

before switching to the

advanced mode.

SmartWare GUI Quick Start Guide

The CD-ROM also includes many freeware and shareware tools, including TFTP servers, and Telnet clients.

Besides the comprehensive manuals included on the CD-ROM a host of additional information is available on-line

www.patton.com/voip

. Here you will ﬁnd:

•

Conﬁguration notes

—This library contains example command sets for conﬁguring and activating such

SmartWare services as DHCP, QoS, VPNs, Frame-Relay, and many others. Patton offers these examples to help

you implement selected features and functions from within SmartWare's rich set of software services.

•

Application notes

—Application Notes are product speciﬁc complete conﬁguration descriptions and conﬁg-

uration ﬁles for various SmartNode applications. Use these conﬁgurations as templates for your installation.

•

Frequently asked questions (FAQs)

—Provide answers to common questions on SmartNode and VoIP

technology. Such as, how much bandwidth for a VoIP call, where to get a license key etc.

•

Declaration of Conformance

—English and German same as Document Number: 13216U7-001 Rev. B

•

Legal notice

—Same as Document Number: 13216U7-001 Rev. B

SmartWare GUI Quick Start Guide

A.0 Customer and Technical Support

If you contact Patton support, you should have some system information ready to help us better help you. This

information allows us to quickly identify what product you are using and how it is conﬁgured. Therefore, we

integrated a “system report” page that collects all relevant information and presents it to you on one web page.

Click on “Support” to access this page – the page also gives you instructions on where to send the report.

Figure 8.

Request for Support page

Toll-Free VoIP support: call sip:[email protected] with a VoIP SIP client

Online support: www.patton.com

E-mail support: [email protected]—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

Other manuals for SMARTNODE 1200

This manual suits for next models

Table of contents

Other Patton electronics Network Router manuals

Patton electronics

Patton electronics Patton SmartNode 2300 Series User manual

Patton electronics

Patton electronics ONSITE 2603 User manual

Patton electronics

Patton electronics IpLink 2884 User manual

Patton electronics

Patton electronics Patton IPLink 2603 User manual

Patton electronics

Patton electronics SMARTNODE 4552 User manual

Patton electronics

Patton electronics SMARTNODE 4110 Series User manual

Patton electronics

Patton electronics SMARTNODE 4900 User manual

Patton electronics

Patton electronics 4630 Series User manual

Patton electronics

Patton electronics SmartNode 4520 Series User manual

Patton electronics

Patton electronics SmartNode 4960 Series User manual

Patton electronics

Patton electronics 2121 User manual

Patton electronics

Patton electronics IPLink 2802 User manual

Patton electronics

Patton electronics SL4020 User manual

Patton electronics

Patton electronics IPLink 3210 Series User manual

Patton electronics

Patton electronics OnSite 2884 User manual

Patton electronics

Patton electronics 3210 User manual

Patton electronics

Patton electronics ONSITE 2603 User manual

Patton electronics

Patton electronics Patton IPLink 2603 User manual

Patton electronics

Patton electronics OnSite 2800 Series User manual

Patton electronics

Patton electronics IPLink 2821 User manual

Patton electronics

Patton electronics IPLink 2803 User manual

Patton electronics

Patton electronics OnSite 2800 Series User manual

Patton electronics

Patton electronics SMART NODE 4950-NCE User manual

Patton electronics

Patton electronics 2135 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview