Patton electronics SmartNode 07MSN5200-QS User manual

SmartNode™ Model 5200

Enterprise Session Border Router

Quick Start Guide

Important

—

This is a Class A device and is intended for use in a light industrial (commer-

cial) environment only. It is not intended nor approved for use in a heavy industrial or resi-

dential environment.

This device is approved for connection to the public ISDN telecommunication network, over BRI/S0-

ISDN interfaces.

Part Number: 07MSN5200-QS, Rev. B

Revised: February 6, 2012

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

2SmartNode 5200 Quick Start Guide

• Do not open the device when the power cord is connected. For sys-

tems without a power switch and without an external power

adapter, line voltages are present within the device when the power

cord is connected.

• For devices with an external power adapter, the power adapter shall

be a listed Limited Power Source The mains outlet that is utilized to

power the device shall be within 10 feet (3 meters) of the device,

shall be easily accessible, and protected by a circuit breaker in compli-

ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all

applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2

& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet

(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are

rated for proper voltage, current, anticipated temperature, flammabil-

ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages

present regardless of whether the device is powered ON or OFF.

PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,

xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net-

work voltages” and to avoid electric shock use caution when working

near these ports. When disconnecting cables for these ports, detach

the far end connection first.

• Do not work on the device or connect or disconnect cables during peri-

ods of lightning activity.

This device contains no user serviceable parts. This device can only be

repaired by qualified service personnel.

This device is NOT intended nor approved for connection to the PSTN. It

is intended only for connection to customer premise equipment.

WARNING

SmartNode 5200 Quick Start Guide 3

1.0 Power up the SmartNode

1. Connect the SmartNode to a power source using the included power supply and cable.

2. When the Power LED stops blinking and remains lit, the SmartNode is ready to configure.

2.0 Set your PC to DHCP

This guide will allow you to quickly access the configuration interface of a SmartNode and give an overview of

the different elements you can or need to configure. For detailed information on all configuration parameters,

refer to the SmartWare Software Configuration Guide available online at www.patton.com/smartnode.

The SmartNode has a built in DHCP Server which allows an automatic IP connection with a connected PC. To pre-

pare the connection you need to configure the PC to use DHCP. The following paragraphs show how to do this on

Windows. For other operating systems refer to the operating instructions of the PC.

Electrostatic Discharge (ESD) can damage equipment and impair electrical

circuitry. It occurs when electronic printed circuit cards are improperly

handled and can result in complete or intermittent failures. Do the follow-

ing to prevent ESD:

• Always follow ESD prevention procedures when removing and replac-

ing cards.

• Wear an ESD-preventive wrist strap, ensuring that it makes good

skin contact. Connect the clip to an unpainted surface of the chassis

frame to safely channel unwanted ESD voltages to ground.

• To properly guard against ESD damage and shocks, the wrist strap

and cord must operate effectively. If no wrist strap is available,

ground yourself by touching the metal part of the chassis.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, flam-

mability, and mechanical serviceability.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, flam-

mability, and mechanical serviceability.

CAUTION

4SmartNode 5200 Quick Start Guide

1. Right-click on My Network Places and select Properties in the context menu (see figure 1).

Figure 1. Displaying the Network Connections window

Figure 2. Displaying the Internet Properties (TCP/IP) Properties window

2. Double-click on Local Area Connection and click on Properties to open the Internet Protocol (TCP/IP)

Properties window (see figure 2).

3. Select Obtain an IP address automatically and Obtain DNS server address automatically options.

4. Click OK to save changes and close the properties windows.

SmartNode 5200 Quick Start Guide 5

3.0 Connecting the SmartNode to your laptop PC

First the SmartNode must be connected to the mains power supply with the power cable. Wait until the Power

LED stops blinking and stays lit constantly. Now the SmartNode is ready.

The SmartNode 5200 Series is equipped with Auto-MDX Ethernet ports, so you can use straight-through cables

for host or hub/switch connections (see figure 3).

Figure 3. Connecting the SmartNode to your laptop PC

The SmartNode comes with a built-in DHCP server to simplify configuration. Therefore, to automatically config-

ure the PC for IP connectivity to the SmartNode, the laptop PC must be configured for DHCP. The SmartNode will

provide the PC with an IP address. You can check the connection to the SmartNode by executing the ping com-

mand from the PC command window as follows:

ping 192.168.1.1

The interconnecting cables shall be acceptable for external use and shall be rated for the proper appli-

cation with respect to voltage, current, anticipated temperature, flammability, and mechanical service-

ability.

CAUTION

Straight-through wired cable

LAN (ETH 0/1)

Laptop PC

6SmartNode 5200 Quick Start Guide

4.0 Configuring the desired IP address

4.1 Factory-default IP settings

The factory default configuration for the Ethernet interface IP addresses and network masks are listed in the table

below. Both Ethernet interfaces are activated upon power-up. LAN interface ETH 0/1 (LAN) provides a default

DHCP server, the WAN interface uses DHCP client to automatically assign the IP address and network mask.

If these addresses match with those of your network, go to section 5.0 “Connecting the SmartNode to the

network” on page 7. Otherwise, refer to the following sections to change the addresses and network masks.

4.2 Login

To access the SmartNode, start the Telnet application. Type the default IP address for the router into the address

field: 192.168.1.1. Accessing your SmartNode via a Telnet session displays the login screen. Type the factory

default login: administrator and leave the password empty. Press the Enter key after the password prompt.

password: <Enter>

192.168.1.1>

After you have successfully logged in you are in the operator execution mode, indicated by > as command line

prompt. With the commands enable and configure you enter the configuration mode.

192.168.1.1>enable

192.168.1.1#configure

192.168.1.1(cfg)#

4.3 Changing the WAN IP address

Select the context IP mode to configure an IP interface.

192.168.1.1(cfg)#context ip router

192.168.1.1(ctx-ip)[router]#

Now you can set your IP address and network mask for the interface ETH 0/0 (WAN). Within this example a net-

work 172.16.1.0/24 address is assumed. The IP address in this example is set to 172.16.1.99 (you should set

this the IP address given to you by your network provider).

192.168.1.1(ctx-ip)[router]#interface eth0

192.168.1.1(if-ip)[eth0]#ipaddress 172.16.1.99 255.255.255.0

2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0.

2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.

172.16.1.99(if-ip)[eth0]#

IP Address Network Mask

WAN interface Ethernet 0 (ETH 0/0) DHCP DHCP

LAN interface Ethernet 1 (ETH 0/1) 192.168.1.1 255.255.255.0

DHCP address range 192.168.1.10–192.168.1.19 255.255.255.0

SmartNode 5200 Quick Start Guide 7

Copy this modified configuration to your new start-up configuration. This will store your changes in non-volatile

memory. Upon the next start-up the system will initialize itself using the modified configuration.

172.16.1.99(if-ip)[eth0]#copy running-config startup-config

172.16.1.99(if-ip)[eth0]#

The SmartNode can now be connected to your network.

5.0 Connecting the SmartNode to the network

In general, the SmartNode will connect to the network via the WAN (ETH 0/0) port. This enables the SmartNode

to offer routing services to the PC hosts on LAN (ETH 0/1) port. The SmartNode 5200 Series is equipped with

Auto-MDX Ethernet ports, so you can use straight-through or crossover cables for host or hub/switch connections

(see figure 4).

Figure 4. Connecting the SmartNode to the network

You can check the connection with the ping command from the SmartNode to another host on the network.

172.16.1.99(if-ip)[eth0]#ping <IP Address of the host>

Note If the WAN address is not set to DHCP, to ping a device outside your local LAN you must first configure

the default gateway. (For information on configuring the default gateway, refer to section “Set IP

addresses” in Appendix C, “Command Summary” of the SmartNode Series SmartWare Software Config-

uration Guide.)

The interconnecting cables shall be acceptable for external use and shall be rated for the proper appli-

cation with respect to voltage, current, anticipated temperature, flammability, and mechanical service-

ability.

CAUTION

Straight-through wired or crossover cable LAN (ETH 0/1)

LAN

WAN (ETH 0/0)

Network

8SmartNode 5200 Quick Start Guide

6.0 Loading the configuration (optional)

Patton provides a collection of configuration templates on the support page at www.patton.com/smart-

node—one of which may be similar enough to your application that you can use it to speed up configuring the

SmartNode. Simply download the configuration note that matches your application to your PC. Adapt the config-

uration as described in the configuration note to your network (remember to modify the IP address) and copy

the modified configuration to a TFTP server. The SmartNode can now load its configuration from this server.

Note If your application is unique and not covered by any of Patton’s configuration templates, you can man-

ually configure the SmartNode instead of loading a configuration file template. In that case, refer to the

SmartWare Software Configuration Guide for information on configuring the SmartNode device.

In this example we assume the TFTP server on the host with the IP address 172.16.1.11 and the configuration

named SN.cfg in the root directory of the TFTP server.

172.16.1.99(if-ip)[eth0]#copy tftp://172.16.1.11/SN.cfg startup-

config

Download...100%

172.16.1.99(if-ip)[eth0]#

After the SmartNode has been rebooted the new startup configuration will be activated.

172.16.1.99(if-ip)[eth0]#reload

Running configuration has been changed.

Do you want to copy the 'running-config' to the 'startup-config'?

Press 'yes' to store, 'no' to drop changes : no

Press 'yes' to restart, 'no' to cancel : yes

The system is going down

7.0 Additional information

For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,

refer to the SN5200 User Manual available online at www.patton.com/manuals/SN5200.pdf and the

SmartWare Software Configuration Guide available online at www.patton.com/smartnode.

When you issue the reload command, the SmartNode will ask if you want to copy the running config-

uration to the startup configuration. Since you just downloaded a configuration file to the startup con-

figuration you must answer this question with NO. Otherwise, the downloaded configuration will be

overwritten and lost!

IMPORTANT

SmartNode 5200 Quick Start Guide 9

A.0 Customer and Technical Support

If you contact Patton support, you should have some system information ready to help us better help you. This

information allows us to quickly identify what product you are using and how it is configured. Therefore, we inte-

grated a “system report” page that collects all relevant information and presents it to you on one web page.

Click on “Support” to access this page – the page also gives you instructions on where to send the report.

Toll-Free VoIP support: call sip:support@patton.com with a VoIP SIP client

Online support: www.patton.com

E-mail support: support@patton.com—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

A.0 Appendix—Factory default IP addresses

Factory default IP addresses and netmask configuration.

IP Address Network mask

WAN interface Ethernet 0 (0/0) DHCP Client n/a

LAN interface Ethernet 1 (0/1) 192.168.1.1 255.255.255.0

DHCP server address range (LAN) 192.168.1.10-192.168.1.19 255.255.255.0

10 SmartNode 5200 Quick Start Guide

B.0 Compliance Information

B.1 Compliance

EMC Compliance:

•

EN55022, Class A

•

EN55024

Low-Voltage Directive (Safety Compliance):

•

IEC/EN60950-1, 2nd edition

•

AS/NZS60950-1

PSTN:

•

TBR3:1995 A1

•

AS/ACIF SO31:2001

B.2 CE Declaration of Conformity

This device conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of

the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition of

their conformity.

The safety advice in the documentation accompanying this device shall be obeyed. The conformity to the above

directive is indicated by CE mark on the device.

B.3 Authorized European Representative

D R M Green

European Compliance Services Limited.

Avalon House, Marcham Road

Abingdon,

Oxon OX14 1UD, UK

This manual suits for next models

Table of contents

Other Patton electronics Network Router manuals

Patton electronics

Patton electronics SMARTNODE 5400 User manual

Patton electronics

Patton electronics DIAMONDLINK 3201 User manual

Patton electronics

Patton electronics SMARTNODE 4630 Series User manual

Patton electronics

Patton electronics 2124 User manual

Patton electronics

Patton electronics SmartNode 4830 Series User manual

Patton electronics

Patton electronics SMARTNODE 4900 User manual

Patton electronics

Patton electronics SL4020 User manual

Patton electronics

Patton electronics SmartNode 5200 User manual

Patton electronics

Patton electronics SMARTNODE 4552 User manual

Patton electronics

Patton electronics Patton IPLink 2635 User manual

Patton electronics

Patton electronics SmartNode 4520 Series User manual

Patton electronics

Patton electronics SMART NODE 4950-NCE User manual

Patton electronics

Patton electronics SmartLink 4020 Series User manual

Patton electronics

Patton electronics IM2RC/IA User manual

Patton electronics

Patton electronics IpLink 2884 User manual

Patton electronics

Patton electronics ONSITE 2621 User manual

Patton electronics

Patton electronics OnSite 2800 Series User manual

Patton electronics

Patton electronics DIAMONDLINK 3201 User manual

Patton electronics

Patton electronics 3087 User manual

Patton electronics

Patton electronics 3224 Diamond Edge User manual

Patton electronics

Patton electronics SmartNode 4960 Series User manual

Patton electronics

Patton electronics IPLink 2802 User manual

Patton electronics

Patton electronics 3210 User manual

Patton electronics

Patton electronics 2121 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview