Paradox K32LCD+ User manual

Printed in Canada | 06/2014 K32LCD+ Quick Install Guide

Technical Specifications

Warranty

Warranty: For complete warranty information on this product, please refer to the

Limited Warranty Statement found on the Web site www.paradox.com/terms. Your

use of the Paradox product signifies your acceptance of all warranty terms and

conditions.

notice. www.paradox.com

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

K32LCD+ Keypad

Quick Install Guide

The K32LCD+ keypad allows you to configure your Paradox

system through its interface.

Installation

1. Using a flathead screwdriver, pry the front housing assembly

from the backplate.

Figure 1: Opening the K32LCD+

Operating Voltage 9 to 16Vdc

Operating Temp. -10 to 55°C (14 to 131°F)

Power Consumption Maximum current - 150mA

Dimensions 15 x 12.6 x 2.7 cm (6 x 4.9 x 1.06 in.)

Weight 230g (8.1 oz)

Humidity 5-93%

Compatibility

Compatible with MG5000, MG5050, and Spectra

SP series V2.31 or higher and SP4000, SP65 V4.90

or higher.

Compliance EN50131-3 Grade 2; Environmental Class II

K32LCD+-EI00

K32LCD+ Quick Install Guide Printed in Canada | 06/2014

2. Mount the backplate to the wall by securing a M3.5 (#6)

screw in each of the dedicated mounting holes and tamper

hole. Ensure that the top is up, as shown in figure 2.

Figure 2: Backplate

3. Connect the 4-wire combus wires to the connector bus, as

shown in figure 3.

Figure 3: Wiring

4. Assemble both items by joining the hooks on the backplate

to their respected slots on the front housing assembly.

5. Secure the front housing to the backplate by snapping it

into place.

The installation process is now complete.

Configuration

To configure the modules through a keypad start by:

1. Press and hold the 0 (number zero) key.

NOTE:The area must be disarmed to configure it.

2. Initially you will see User Access Code but within 2 seconds

it will change to Installer Code.

3. When the Installer code appears, input the Installer code

number, the default number is [000000].

4. Input the 4 digit section code for Module Programming

[4003].

NOTE:You need module serial numbers for programming.

5. Input the Module serial number.

6. Input module sec [001].

7. Now you can start module programming.

Compatibility

The K32LCD+ is compatible with Magellan and Spectra series

control panels only. Please refer to the Technical Specifications

section for more details.

Wiring Slot

Wall Tamper

Top with hooks for

mounting keypad

panel

Mounting screw

holes

ZX1 is a:

Programmable

input

PGM is a:

Programmable

output

AllDisarmed

2014/19/0516:00

UserAccessCode

[*_]

InstallersCode

[_]

K32LCD+ Quick Install Guide Printed in Canada | 06/2014

2. Mount the backplate to the wall by securing a M3.5 (#6)

screw in each of the dedicated mounting holes and tamper

hole. Ensure that the top is up, as shown in figure 2.

Figure 2: Backplate

3. Connect the 4-wire combus wires to the connector bus, as

shown in figure 3.

Figure 3: Wiring

4. Assemble both items by joining the hooks on the backplate

to their respected slots on the front housing assembly.

5. Secure the front housing to the backplate by snapping it

into place.

The installation process is now complete.

Configuration

To configure the modules through a keypad start by:

1. Press and hold the 0 (number zero) key.

NOTE:The area must be disarmed to configure it.

2. Initially you will see User Access Code but within 2 seconds

it will change to Installer Code.

3. When the Installer code appears, input the Installer code

number, the default number is [000000].

4. Input the 4 digit section code for Module Programming

[4003].

NOTE:You need module serial numbers for programming.

5. Input the Module serial number.

6. Input module sec [001].

7. Now you can start module programming.

Compatibility

The K32LCD+ is compatible with Magellan and Spectra series

control panels only. Please refer to the Technical Specifications

section for more details.

Wiring Slot

Wall Tamper

Top with hooks for

mounting keypad

panel

Mounting screw

holes

ZX1 is a:

Programmable

input

PGM is a:

Programmable

output

AllDisarmed

2014/19/0516:00

UserAccessCode

[*_]

InstallersCode

[_]

Printed in Canada | 06/2014 K32LCD+ Quick Install Guide

Technical Specifications

Warranty

Warranty: For complete warranty information on this product, please refer to the

Limited Warranty Statement found on the Web site www.paradox.com/terms. Your

use of the Paradox product signifies your acceptance of all warranty terms and

conditions.

notice. www.paradox.com

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

K32LCD+ Keypad

Quick Install Guide

The K32LCD+ keypad allows you to configure your Paradox

system through its interface.

Installation

1. Using a flathead screwdriver, pry the front housing assembly

from the backplate.

Figure 1: Opening the K32LCD+

Operating Voltage 9 to 16Vdc

Operating Temp. -10 to 55°C (14 to 131°F)

Power Consumption Maximum current - 150mA

Dimensions 15 x 12.6 x 2.7 cm (6 x 4.9 x 1.06 in.)

Weight 230g (8.1 oz)

Humidity 5-93%

Compatibility

Compatible with MG5000, MG5050, and Spectra

SP series V2.31 or higher and SP4000, SP65 V4.90

or higher.

Compliance EN50131-3 Grade 2; Environmental Class II

K32LCD+-EI00

Other manuals for K32LCD+

Table of contents

Other Paradox Keypad manuals

Paradox

Paradox Spectra 1641BL User manual

Paradox

Paradox Esprit 616 User manual

Paradox

Paradox TM50 Touch User manual

Paradox

Paradox TM50 Touch User manual

Paradox

Paradox Spectra 1689 User manual

Paradox

Paradox Grafica DNE-K07 Operating instructions

Paradox

Paradox K70C User manual

Paradox

Paradox SP5500 User manual

Paradox

Paradox TM50 Touch User manual

Paradox

Paradox K32LCD Troubleshooting guide

Paradox

Paradox Digiplex EVO DGP2-641BL User manual

Paradox

Paradox Digiplex EVO DGP2-641BL User manual

Paradox

Paradox Digiplex DGP2-648 User manual

Paradox

Paradox Esprit 639 User manual

Paradox

Paradox Digiplex DGP-641 User manual

Paradox

Paradox Esprit User manual

Paradox

Paradox Esprit 636 User manual

Paradox

Paradox K35 User manual

Paradox

Paradox DGP2-641 User guide

Paradox

Paradox Spectra 1641 Assembly instructions

Paradox

Paradox MAGELLAN K10V/H User manual

Paradox

Paradox 1640 User manual

Paradox

Paradox DigiplexNE DGP2-641 User manual

Paradox

Paradox K641 User manual

Popular Keypad manuals by other brands

BFT

BFT SELETTO Installation and user manual

Micro Id

Micro Id MP7G3BL Quick start manual

WindowMaster

WindowMaster WLI 130 installation instructions

ACT

ACT ACT PRO 1030 manual

Cardin

Cardin SSB Series manual

Harman Kardon

Harman Kardon KP 1 Specifications

Chamberlain

Chamberlain KPR2000 Installation setup manual

CYP

CYP CR-KP1 Operation manual

Aeware

Aeware k-35 Series Quick reference card

Aritech

Aritech CS-175 Series user guide

GE NetworX NX-1600E Series user manual

Lenze AC Tech

Lenze AC Tech MC SERIES installation instructions

Burg Wächter

Burg Wächter secuENTRY 7711 operating instructions

Aeware

Aeware in.k450 Tech book

Lenze

Lenze EPM-H410 operating instructions

Toshiba

Toshiba RKP007Z user manual

Gemini

Gemini GEM-DXK1 KEYPAD operating guide

Russound

Russound MDK-C5 User and installation manual