Panduit CT-1002 Manual

Page: 1 of 2

CON ROLLED CYCLE FERRULE CRIMPING OOLS

OPERA ION, INSPEC ION and MAIN ENANCE INS RUC IONS

1. With the handles in

the open position,

insert the ferrule

into the opening at

the top of the tool.

Make sure that the

ferrule insulation or

flared end is up

(see Figure 2). Do

not allow insulation

to be inserted into

crimp die. Close

handles until dies

just slightly crimp

ferrule.

2. Insert the stripped wire into the ferrule until the wire

stops. Refer to product packaging for wire strip length.

3. Crimp the ferrule by closing the handles until the

controlled cycle mechanism releases. Upon release,

the handles will open automatically and the crimped

ferrule can be removed.

1. With the handles in

the open position,

insert the ferrule

into the crimp

pocket. Make sure

that the ferrule is

inserted fully into

the crimp die (see

Figure 4).

2. Insert the stripped

wire into the ferrule

until the wire stops.

Refer to product

packaging for wire

strip length.

3. Crimp the ferrule by closing the handles until the

controlled cycle mechanism releases. Upon release,

the handles will open automatically and the crimped

ferrule can be removed.

NO E: Crimp entire uninsulated ferrule length. This may

require additional crimps.

C -1002, C -1003 and C -1004 OOLS

C -1005 and C -1006 OOLS

Cushioned handle grips

CRIMP POCKET for Insulated

and Non-Insulated Ferrules. Part

usage dependent on wire range.

Refer to product packaging for

proper wire combination.

Controlled cycle mechanism

prevents tool from opening

before crimp cycle is complete.

Manual release lever, push

forward in the event that

controlled cycle mechanism

must be released.

Fig. 1

Fig. 3 Fig. 4

Fig. 2

tripped

Wire

Crimp Die

Die Closure Alignment

(not a crimp pocket)

Controlled cycle mechanism pre-

vents tool from opening before

crimp cycle is completed.

Manual release lever, push

forward in the event that

controlled cycle mechanism

must be released.

Cushioned handle grips

Ferrule

Insulation

section Ferrule -

Metal crimp

section

tripped

Wire

CRIMP POCKET for Ferrule

terminals. Refer to product

packaging for wire range and

proper crimp pocket. Crimp

pockets are identified with

applicable wire range.

Ferrule - Wire

crimp section

Ferrule Insulated

section

C -1002, C -1003, C -1004,

C -1005 and C -1006

PA24073A01

REV: 04 2-2018

E-mail:

[email protected]

For echnical Support:

1-800-777-3300

www.panduit.com

CAUTION:

Verify power is “OFF” before working

on wiring with these tools.

The plastic grips are for the user’s

comfort, and are not intended

to insulate against electrical shock

while working on li e electrical circuits.

Page: 2 of 2

NEW OOLS - BEFORE PLACING IN O SERVICE:

All Panduit crimping tools are inspected before they are shipped from the factory. All new tools should be inspected

before being used.

New tools are shipped, factory lubricated, in protective packaging. After inspection, simply clean any excess oil from the

crimping dies and place into service.

When the tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping area. tore

the tool in a clean, dry area.

IN SERVICE OOLS - AF ER OOLS HAVE BEEN IN SERVICE:

It is recommended that each operator of the tool be made aware of - and responsible for following these maintenance

steps:

In-service tools should be cleaned and inspected at least ONCE A MONTH. To clean - wipe with a clean cloth.

In-service tools should be lubricated ONCE A WEEK, and after every cleaning. Lubricate all pins, pivots and bearing

surfaces with DOW CORNING®Molykote BR2 Plus.

Be sure to clean any excess oil from the crimping dies before using.

®Molykote BR2 Plus is the Registered Trademark of DOW CORNING.

INSPEC ION / MAIN ENANCE

VISUAL INSPEC ION

1. Visually inspect the tool for missing or loose pins; then close the tool and note the return action of the handles.

2. Inspect the crimping dies for worn, chipped or broken edges.

3. If parts are missing, defective or damaged; contact Panduit for information on repair or replacement of tools.

4. Check for debris in dies. Any debris will need to be removed prior to tool use.

OPERA ION, INSPEC ION and MAIN ENANCE INS RUC IONS

This manual suits for next models

Table of contents

Other Panduit Crimping Tools manuals

Panduit

Panduit BlackFin CT-2300 Series User manual

Panduit

Panduit CT-2002CH User manual

Panduit

Panduit CT-3001 User manual

Panduit

Panduit CT-460 User manual

Panduit

Panduit CTFP-100 User manual

Panduit

Panduit PAT4.0 Series User manual

Panduit

Panduit BlackFin CT-2980/ST User manual

Panduit

Panduit BlackFin CT-3980/BT User manual

Panduit

Panduit Black Fin CT-2931 Series User manual

Panduit

Panduit PBTMT User manual

Panduit

Panduit CT-920 Series User manual

Panduit

Panduit BlackFin CT-2980/STBT User manual

Panduit

Panduit BlackFin CT-2920 User manual

Panduit

Panduit CT-1104 Instruction Manual

Panduit

Panduit CT-930LPCH User manual

Panduit

Panduit ClackFin CT-3001/CCPBT User manual

Panduit

Panduit CT-1003 Instruction Manual

Panduit

Panduit BlackFin CT-2300/ST User manual

Panduit

Panduit CTFP-25 User manual

Panduit

Panduit Contour Crimp CT-1551 User manual

Panduit

Panduit CT-2940/L User manual

Panduit

Panduit BlackFin CT-2931/STBT User manual

Panduit

Panduit CT-1123 Instruction Manual

Panduit

Panduit CT-1123 Instruction Manual

Popular Crimping Tools manuals by other brands

JST

JST CS 10 instruction manual

molex

molex 63811-5100 Specification sheet

Danfoss

Danfoss ET4200 Operator's manual

Tyco Electronics

Tyco Electronics PRO-CRIMPER III instruction sheet

TE Connectivity

TE Connectivity 2063528-1 instruction sheet

molex

molex 63825-3000 Specification sheet

Tyco Electronics

Tyco Electronics 69156-1 instruction sheet

CRH

CRH CRL CBLHCT1 instruction manual

Emerson

Emerson Klauke ES 105CFM manual

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Operating instructions manual

Danfoss

Danfoss ET4350 Operator's manual

Milwaukee

Milwaukee M18 Operator's manual

HOGERT

HOGERT HT1P169 user manual

Textron

Textron ESG105L instruction manual

Tyco Electronics

Tyco Electronics 90035-3 instruction sheet

Emerson

Emerson Klauke ES 20RMCCFB manual

Continental Refrigerator

Continental Refrigerator PC150HD quick start guide

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 instruction sheet