Panasonic ES8026-E2 User manual

ORDERNO. SD0203E40C2

Wet/DryRechargeableShaver

ES8026-E2

SPECIFICATIONS

Power source AC100-240V, 50-60Hz

(Automaticvoltageconversion)

Power consumption 90mA

Motorvoltage 2.4V DC

Charging time 1-hour

Shaves per charge 14 times (3minutes shave)

Measurement (H) 14.0X (W) 6.0X (D) 3.5cm

Weight 230g, 0.51lbs

Suppliedaccessory Soft case

Unauthorized copying and distribution isaviolation of law.

1. SCHEMATIC DIAGRAM

2. WIRING CONNECTION DIAGRAM

3. DISASSEMBLY INSTRUCTIONS

Followthe procedure belowtodisassemble the mainunit.

1. Remove the cap, the outer foil with foil frame and the inner blades.

2. Unhook the right and left side of hooks at upside using aflat

screwdriver with aposition 8mm sliding above. Then slightly

move the trimmer until position marking , and unhook the

lower side of hooks.

To remove the trimmer driving bars, press bar outward.

3. Loosen twoscrewsand the retaining plate. Take out the

waterproof rubber and the blade mounting base.

4. Loosen twoscrewson the bottom.

5. Take out the actuator from housing. Donot push the switch

button when removing or inserting the actuator. Itmaycause the

break of the pushed switch.

4. CAUTION IN ASSEMBLY

NOTE: Whenreassembling, replace the newwaterproof rubber.

4.1. Battery

4.1.1. Replacement

To remove battery, fix the top of batteryterminal witha flat plate and lifting up the batterypin.

4.1.2. Attachment

Followthe procedure toprevent the deformation of batteryterminal.

1. Install (+)terminal of batterypininto the terminal.

2. Firmlyset the batterysliding the direction of arrow.

3. Attach (-) terminal of battery.

4.2. Waterproof Rubber

The waterproof rubbermust be fittedthe right wayaround. Install as showninfigure by

inserting firmlytothe set position.

4.3. Trimmer

Set a position where marking and hook lowerside of twohooks. Witha position 8mm

sliding down, hook right and left side of hooks at upside.

4.4. Module

Module is solderedwithconnection terminal of chassis.

Followthe stepbelowtoremove the module.

1. Unsolder four points A, B, C, and D.

2. Remove the modulefrom four hooks with chassis.

5. TROUBLESHOOTING GUIDE

(RefertoWIRING CONNECTION DIAGRAM)

< TROUBLE > < CHECK. > <

REMEDY

Motordoes not rotate. <CHECK CHARGING ADAPTOR.>

Does not charge. Connect toratedvoltage withthe normal main

unit set ontothe NOReplace

charging

Functions fora

moment and adaptor. adaptor.

stops. Check if the charging lampof mainunit is lit.

<CHECK RECHARGEABLE BATTERIES.> NOReplace

both

recharge-

Okayif the voltage of rechargeable batteries is

more thanapproxi- able

batteries

the

mately1.2V DC between(+) and (-) terminals. same

time.

(Replace tworechargeable batteries at the same

time eventhough

one batteryis defective due toseries connection.)

<CHECK MODULE.> NOCheck

the

soldering

Insert the actuatorintothe housing, and connect

toratedvoltage points

from

withthe normal adaptor. It is OK, if LED of main

unit is flashing.

Replace

module.

OK Replace

linear

motor.

<CHECK MODULE.> OKGotothe

step,

"Check

Whenswitching ON and OFF, it is OK if LED is

flashing and the charging

current".

motorrotates.

<CHECK MODULE.> OK Replace

linear

motor.

Check the soldering condition at eachparts from

A toD.

Replace

module.

Resolder.

6. TROUBLESHOOTING GUIDE

(RefertoWIRING CONNECTION DIAGRAM)

< TROUBLE > < CHECK.> <

REMEDY

Noise is too loud. Oiling a drop forthe outerfoil.

Amplitude is too large. NO

<CHECK TRIMMER DRIVING BARS.> NO Replace

the

trimmer

Check if there is anydeformation withtrimmer

driving barA and B. driving

bar.

<CHECK DRIVING HEAD AMPLITUDE.> NO Replace

linear

motor.

Turnthe switchON, and measure the amplitude

using a pinof

drivinhead. (See the figure shownbelow.) Replace

module.

Amplitude is too

small. <CHECK DRIVING HEAD AMPLITUDE.> NO Replace

linear

motor.

Does not sharp

enough. Turnthe switchON, and measure the amplitude

using a pinof (onlythe

case

the

drivinhead. (See the figure as shownabove.) amplitude

clear-

ance (

2.8mm

full

wideth.))

Replace

module.

Does not function, but <CHECK MODULE.> NO Replace

module.

LED flashes. Take out the right battery. (Viewedfromthe front.)

Connect lead

wire withchassis and (-) terminal of battery. Check

charging current Replace

linear

motor.

betweenleadwire comes frommodule side (stated

on WIRING CON-

NECTION DIAGRAM) and (+) terminal of battery

setting on the normal

adaptor. Okayif it is more than600mA when

connecting torated

voltage.

NOTE: The charging current fluctuates depending on the space betweencharging adaptorand

the coil. / Please followthe procedure below.

1. Put the coil and the bottom part of housing close together.

2. Put the bottom part of housing and the charging adaptor close

together.

3. Measure the charging currents between (+)terminal of batteryand

lead wire comes from moduleside.

7. EXPLODED VIEW

8. REPLACEMENT PARTS LIST

NOTE

*A=available as anoptional accessory

*B=onlyavailable as set

*C=available individually

Ref. No. PartNo. PartName& Descriptions Remarks Per Unit

1WES8023X7158 PROTECTIVE CAP 1

2WES9077Y OUTER FOIL 1

3WES8026N0048 OUTER FOIL FRAME 1

4WES9072Y INNER BLADE *B 2

5WES882L9709 SCREW *C 2

6WES8035L0207 RETAINING PLATE 1

7WES8003L0327 WATER-PROOF RUBBER 1

8WES8921H0007 BLADEMOUNTING BASE 1

9WES7006H3267 FOIL FRAMERELEASE BUTTON *C 2

10 WES3001L0177 SPRING FOR RELEASE BUTTON *C 2

11 WES8026S3158 HOUSING 1

12 WES8026S3968 SWITCH PANEL 1

13 WES8080H1507 TRIMMER 1

14 WES762L6007 SCREW *C 2

15 WES8035L1077 TRIMMER DRIVING BAR B 1

16 WES8068L1087 TRIMMER DRIVING BAR A 1

17 WES8950L4307 LINEAR MOTOR ASSEMBLY 1

18 WES8035L1007 LINEAR MOTOR 1

19 WES8950L2127 MODULE 1

20 WES8035L0777 CHASSIS 1

21 WES882L2508 RECHARGEABLEBATTERY Ni-Mh type 1

22 WES8921L0607 RUBBER 1

23 WES8026S8409 NAMEPLATE 1

24 WES8026S3038 BODYBLOCK 1

25 WES8026H7664 CHARGING ADAPTOR C-2 plug 1

25 WES8026H7660 CHARGING ADAPTOR B-2 plug (U.K.) 1

26 WES663S6007 SCREW *B 2

27 WES8023A7008 SOFTCASE 1

28 WES861B7057 CLEANING BRUSH 1

- WES8026S8008 INDIVIDUAL BOX 1

-WES8026S8108 OPERATING INSTRUCTIONS 1

Table of contents

Other Panasonic Electric Shaver manuals

Panasonic

Panasonic ER2405K User manual

Panasonic

Panasonic ES-CT30 User manual

Panasonic

Panasonic ES?ST25 User manual

Panasonic

Panasonic ER-GK40 User manual

Panasonic

Panasonic ES3831 User manual

Panasonic

Panasonic ES-LV97 User manual

Panasonic

Panasonic ES-LT71 User manual

Panasonic

Panasonic ES2235 User manual

Panasonic

Panasonic ES2205A User manual

Panasonic

Panasonic ES4815 User manual

Panasonic

Panasonic ER2403K User manual

Panasonic

Panasonic ES4033 User manual

Panasonic

Panasonic ES-8078 User manual

Panasonic

Panasonic ES-LF71 User manual

Panasonic

Panasonic ES-7017 User manual

Panasonic

Panasonic ES-7015 User manual

Panasonic

Panasonic ES-8080 User manual

Panasonic

Panasonic ES-2113 User manual

Panasonic

Panasonic ER220-E2 User manual

Panasonic

Panasonic ES-LA62 User manual

Panasonic

Panasonic ER-GN25VP User manual

Panasonic

Panasonic ES-8807 User manual

Panasonic

Panasonic ES-LV5B User manual

Panasonic

Panasonic ES-LS8A User manual

Popular Electric Shaver manuals by other brands

Philips

Philips MicroAction 4402LC Specifications

Philips

Philips HQ7740 user guide

Philips

Philips Norelco BG2022 Bodygroom Specifications

Norelco

Norelco Quadra 7610X owner's manual

Philips

Philips 7616X manual

Philips

Philips HQ802 Specifications

Philips

Philips HQ7363/17 user manual

Braun

Braun WaterFlex WF2s manual

Philips

Philips NORELCO S7371 manual

Daga

Daga MT-400 Directions for use

Philips

Philips RQ119x manual

Remington

Remington BHT100 user manual

Philips

Philips Bodygroom BG2000 brochure

Kompernass

Kompernass KH 5537 operating instructions

Remington

Remington BHT6100 manual

Philips

Philips qc5365 user manual

MIA

MIA Aqua Body manual

Philips

Philips NORELCO AT880 user manual