Panasonic WVRM70 - ACCESSORY User manual

Camera Controller

WV-RM70

Before attempting to connect or operate this product,

please read these instructions completely.



WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The lightning flash with arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the pres-

ence of uninsulated "dangerous volt-

age" within the product's enclosure that

may be of sufficient magnitude to con-

stitute a risk of electric shock to per-

sons.

The exclamation point within an equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing)

instructions in the literature accompa-

nying the appliance.

The serial number of this product may be found on the bot-

tom of the unit.

You should note the serial number of this unit in the space

provided and retain this book as a permanent record of your

purchase to aid identification in the event of theft.

Model No.

Serial No.

Warning:

This equipment generates and uses radio frequency energy

and if not installed and used properly, i.e., in strict accor-

dance with the instruction manual, may cause harmful

interference to radio communications. It has been tested

and found to comply with the limits for a Class A computing

device pursuant to Subpart J of Part 15 of FCC Rules,

which are designed to provide reasonable protection

against such interference when operated in a commercial

environment.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER SER-

VICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PER-

SONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SA 1965

SA 1966

For U.S.A

CAUTION:

Before attempting to connect or operate this prod-

uct, please read the label on the bottom.

-1-

CONTENTS

PREFACE ...................................................................................................................................................................... 2

FEATURES .................................................................................................................................................................... 2

PRECAUTIONS ............................................................................................................................................................. 3

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ....................................................................................... 4

CONNECTIONS ............................................................................................................................................................ 7

OPERATING PROCEDURE ........................................................................................................................................... 13

SPECIFICATIONS ......................................................................................................................................................... 32

-2-

PREFACE

The WV-RM70 Camera Controller, when combined with

the optional WV-CP610 and WV-BP510 series CCTV

Camera, enables remote control of camera settings.

Also it is available to receive the alarm (motion detec-

tor) signal multiplexed with the video signal from the

WV-CP610 and WV-BP510 series camera.

FEATURES

The WV-RM70 Camera Controller enables remote con-

trol of the following functions:

• Remote control of camera settings for the WV-

CP610 and WV-BP510 series camera, including

Electronic Sensitivity Up, Electronic Shutter, and

more.

• Remote control of camera and auxiliary equipment,

by using optional receiver and accessories, includ-

ing:

1. Remote control of Pan/Tilt Head and Camera

Housing.

2. Remote control of Motorized Zoom Lens :

Focus, Zoom and Iris.

Also it is available to receive the alarm (motion detec-

tor) signal multiplexed with the video signal from the

WV-CP610 and WV-BP510 series camera.

-3-

PRECAUTIONS

• Do not attempt to disassemble the unit.

In order to prevent electric shock, do not remove

screws or covers. There are no user-serviceable

parts inside.

Do refer to all servicing to qualified service person-

nel.

• Handle the unit with care.

Do not abuse the unit. Avoid striking, shaking, etc.

It could be damaged by improper handling or stor-

age.

• Do not expose the unit to rain or moisture, or try to

operate it in wet areas.

Do take immediate action if the unit becomes wet.

Turn the power off and refer servicing to qualified

service personal. Moisture can damage the unit

and also create the danger of electric shock.

• Do not use strong or abrasive detergents when

cleaning the unit body.

Do use a dry cloth to clean the unit when dirty.

In case the dirt is hard to remove, use a mild deter-

gent and wipe gently.

• Do not operate the unit beyond its temperature,

humidity or power source ratings.

Do not use the unit in an extreme environment

where high temperature or high humidity exist. Use

the unit under conditions where temperatures are

within 14˚F-140˚F (−10˚C - +60˚C) and humidity is

below 90%.

The input power source is 12V DC (10.8 - 16.0V

DC).

Caution: To prevent fire or shock hazard, the UL list-

ed wire VW-1, style 1007 should be used for the

cable for DC12V Input Terminal.

-4-

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

REMOTE

OPERATE

Camera Controller WV-RM

PROG ALARM

RESET

NORMAL

SYSTEM

ALARM OFF

ON OFF

INOUT

TERM VIDEO CAMERA DC12V IN

GNDGND

ALARM OUT

RESET OUT DATA

T(A) T(B) R(A) R(B)

qw e r t y u i o !0 !1 !2 !3 !4 !5 !6

-5-

1. Power Indicator (OPERATE)

This indicator lights up when DC power is supplied

to the DC 12V Input Terminal.

2. Remote Indicator (REMOTE)

This indicator lights up when this controller is con-

trolled remotely by Personal Computer.

3. Left Switch (A)

This switch is used to move the cursor (in the

Setup Menu) in the left direction or move the

Pan/Tilt Head toward the left direction.

4. Down Switch (C)

This switch is used to move the cursor (in the Setup

Menu) in the down direction or move the Pan/Tilt

Head toward the down direction.

5. Up Switch (D)

This switch is used to move the cursor (in the Setup

Menu) in the up direction or move the Pan/Tilt Head

toward the up direction.

6. Set Switch

The mode selected in the setup menu is enabled

by pressing this switch.

7. Right Switch (B)

This switch is used to move the cursor (in the Setup

Menu) in the right direction or move the Pan/Tilt

Head toward the right direction.

8. Mode Selection Switch

(NORMAL/ALARM OFF/SYSTEM)

This switch is used to select the activated mode.

Refer to the Mode Selection on page 13 for more

details.

9. Program Switch (PROG)

This switch is used to display the Program Menu on

the monitor screen by pressing this switch for more

than 2 seconds,

10. Alarm Reset Switch (ALARM RESET)

When the unit is in the alarm mode, this indicator

starts blinking. Press this switch to cancel alarm

and the indicator light turns off.

11. Alarm Terminal

RESET OUT: When the controller resets the acti-

vated alarm by pressing the Alarm Reset

Switch, the alarm reset output signal is provid-

ed at this terminal for the Time Lapse VCR.

-6-

ALARM OUT: The alarm output signal is provided

at this terminal for the Time Lapse VCR.

12. Data Terminal

These terminals are used to transmit / receive

control data to / from a Personal Computer. Use

data grade cable, suitable for RS-485 (2 shielded,

twisted pairs), cable length may be extended up to

4,000 ft. (1,200m).

DesignationDirection

T (A) Personal Computer ←Controller

T (B) Personal Computer ←Controller

GND

R (A) Personal Computer →Controller

R (B) Personal Computer →Controller

GND

13. Termination Switch (TERM ON/OFF)

This switch is used to enable termination of this

controller’s data terminal.

14. Video Output Connector (VIDEO OUT)

A 1.0 Vp-p / 75Ωcomposite video signal is provid-

ed at this connector.

15. Camera Input Connector (CAMERA IN)

This connector accepts either a color or B/W com-

posite video signal from the camera. Also, VD2, to

synchronize camera in vertical timing, and data, to

control camera site devices, are multiplexed

through this connector.

16. DC 12V Input Terminal (DC 12V IN)

This terminal accepts 12V DC (10.8 - 16.0V DC)

power source.

Cautions :

1. Connect to a 12V DC class 2 power supply only.

2. To prevent fire or shock hazard, the UL listed

wire VW-1, style 1007 should be used for the

cable for DC 12V Input Terminal.

-7-

CONNECTIONS

1. Dip Switch Setting

Before connecting this controller, confirm the Dip

Switch Setting if the system setting change is required.

Pulse (VTR): +5V DC approx. 500msec.

Initially, VTR position is selected at the factory.

2. Set switch (SW2) on the board to choose the char-

acter display mode on the monitor.

NOR : White with Black border

REV : Black with White border

Initially, normal (NOR) position is selected at the

factory.

OPC

VTR

REV

NOR REV

NOR

SW1

SW2

SW5

SW3

SW4

Front

Rear

1. Set switch (SW1) on the board to

choose the alarm reset output sig-

nal as either Open Collector (OPC)

or Pulse (VTR).

Open Collector (OPC) :

16V DC 100mA max.

3. Confirm switches (SW3) on the

board are set to the position as

shown. These switches are used

only for factory test.

4. Confirm switch (SW4) on the

board is set to the "VS" position.

This switch is used only for fac-

tory test.

1234

OFF

VD VS

-8-

5. Set switch (SW5) on the board to choose the data

line selection mode for data terminal.

4 LINE : normal connections are

made.

2 LINE : simplified connections

are made.

Initially, 4 LINE is selected

at the factory.

The above switching should be made by qualified

service personal or system installers.

2. Connection of Alarm Output Terminal

• Make sure the polarity of the buzzer to meet with

this terminal.

The positive (+) terminal of

the buzzer should be con-

nected with the Alarm Output

Terminal.

• The Alarm Output Terminal is

composed of the Open

Collector Output and the

capacity is 16V DC, 100mA

or less.

2LINE

4LINE

GND

ALARM OUT

RESET OUT

(1) In case the buzzer is operable within the capacity

of Alarm Output Terminal, connect buzzer as

shown right.

(2) In case the buzzer is not operable within the

capacity of Alarm Output Terminal, the external

relay unit should be used as shown below.

GND

ALARM OUT

RESET OUT

NC NO

+12V

NC : Normally Closed

NO : Normally Open

C : Common

To Buzzer

Relay

Buzzer

Other manuals for WVRM70 - ACCESSORY

Table of contents

Other Panasonic Camera Accessories manuals

Panasonic

Panasonic H-H014A User manual

Panasonic

Panasonic WV-Q152C User manual

Panasonic

Panasonic VW-BTA1 User manual

Panasonic

Panasonic AWPH300 - INDOOR PAN/TILT HEAD User manual

Panasonic

Panasonic AJ-CA900P User manual

Panasonic

Panasonic DVCPRO AJ-CA901 User manual

Panasonic

Panasonic PPDW12 Operation manual

Panasonic

Panasonic WV7230 - CCTV ACCESSORIES User manual

Panasonic

Panasonic VIDEOALARM PODV7CWNS/PODV7CPNS User manual

Panasonic

Panasonic HX025 User manual

Panasonic

Panasonic LC-P0612P User manual

Panasonic

Panasonic DMWVF1 User manual

Panasonic

Panasonic DMW-LMC52PP User manual

Panasonic

Panasonic AJ-DE97P User manual

Panasonic

Panasonic AW-AD700BS User manual

Panasonic

Panasonic AWPH650N - PAN/TILT HEAD User manual

Panasonic

Panasonic VIDEOALARM PODV7CPNS User manual

Panasonic

Panasonic AWRP120GJ User manual

Panasonic

Panasonic CGR18650AF User manual

Panasonic

Panasonic WV-7120D User manual

Panasonic

Panasonic WV7110A - MONITOR User manual

Panasonic

Panasonic AM-2PI User manual

Panasonic

Panasonic WX-SB100E User manual

Panasonic

Panasonic WV-VF39 User manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions