Panasonic AW- PH350 User manual

Before attempting to connect, operate or adjust this product, please

read these instructions completely.

Indoor pan-tilt head

Model AW- P

F1101W @

Printed in Japan

VQT9583 P

indicates safety information.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle,

is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (service)

instructions in the literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING

INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER

CHANGE OF SWITCH SETTING INSIDE THE UNIT TO QUALIFIED

SERVICE PERSONNEL.

indicates safety information.

Replace battery with part No. CR2032 only.

Use of another battery may present a risk of fire or explosion.

Caution—Battery may explode if mistreated.

Do not recharge, disassemble or dispose of in fire.

FCC Note:

This device complies with Part 15 of the FCC Rules. To assure continued

compliance follow the attached installation instructions and do not make any

unauthorized modifications.

This equipment has been tested and found to comply with the limits for a class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

OThis is a compact stand-alone type of

pan-tilt head which is capable of rotating

95 degrees upward and downward and

300 degrees on the horizontal.

OThis pan-tilt head can bear a total weight

of up to 8.8 lb (4 kg) for the camera and

lens combined.

OThe pan-tilt head can be controlled

directly using the Multi-Function

Controller (AW-RP605). Up to five pan-

tilt heads can be connected to the Multi-

Function Controller (AW-RP605).

OThe pan-tilt head can be controlled from

a PC, etc. by converting RS-232C to RS-

422.

OThe positions and settings for shooting

up to 50 points can be entered as data

into the preset memory.

Introduction

Tilting arm . . . . . . . . . . . . . . . . . . . . . .(a1)

Tilting arm fixing screws

M4a12 mm . . . . . . . . . . . . . . . . . . .(a4)

Safety chain . . . . . . . . . . . . . . . . . . . .(a1)

Chain attachment screws

(with flat and spring washers)

M4a8 mm . . . . . . . . . . . . . . . . . . . .(a1)

M4a6 mm . . . . . . . . . . . . . . . . . . . .(a1)

M2.6a6 mm . . . . . . . . . . . . . . . . . . .(a1)

Accessories

Please check the following accessories have been provided.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . .4

Accessories . . . . . . . . . . . . . . . . . . . . . .4

Installation precautions . . . . . . . . . . . . .5

Precautions for use . . . . . . . . . . . . . . . .6

Parts and their functions . . . . . . . . . . . .7

Installation . . . . . . . . . . . . . . . . . . . . . . . .9

$Assembling the pan-tilt head . . . . . . .9

$Setting the installation direction

selector switch and landing

characteristics . . . . . . . . . . . . . . . . .10

$Setting the cable compensation

circuit . . . . . . . . . . . . . . . . . . . . . . . .11

$Moving the mounting position of the

base connector panel . . . . . . . . . . .12

$Changing the mounting direction of the

base connector panel . . . . . . . . . . .12

$Installing the pan-tilt head . . . . . . . .13

$Mounting the camera . . . . . . . . . . . .14

Connections . . . . . . . . . . . . . . . . . . . . .18

$Connecting the connector panel . . .18

$Head connector panel . . . . . . . . . . .19

$Connecting the base connector

panel . . . . . . . . . . . . . . . . . . . . . . . .20

$Connecting the AC adapter for use

with the pan-tilt head . . . . . . . . . . . .21

$Setting the printed circuit board

switches . . . . . . . . . . . . . . . . . . . . . .22

Examples of connections . . . . . . . . . .23

Limiters . . . . . . . . . . . . . . . . . . . . . . . . .29

$Setting the limiters . . . . . . . . . . . . . .30

$Releasing the limiters . . . . . . . . . . .31

$Resetting the limiters . . . . . . . . . . . .31

Replacement of consumable parts . . .32

Specifications . . . . . . . . . . . . . . . . . . . .33

Installation precautions

OAvoid using the pan-tilt head in kitchens or other places where there is excessive steam

and oil fumes.

OMake sure that the installation of the pan-tilt head has been completed before mounting

the camera onto it.

OThis pan-tilt head has a maximum load capacity of 8.8 lb (4 kg).

Do not use it for loads over 8.8 lb (4 kg).

ODo not use a lens that will cause the camera to be poorly balanced. Such a lens should

not be used even if the load capacity is under 8.8 lb (4 kg).

ODo not install the pan-tilt head outdoors or in any place where the temperature is over

113°F (45°C) or below 14°F (–10°C).

Further, it should be used where the ambient humidity is less than 90%.

OScrews for mounting the pan-tilt head are not provided with the stand and must therefore

be purchased separately.

They should be selected with due consideration given to the location where the pan-tilt

head is to be mounted and its load capacity.

OTo supply power to the pan-tilt head, use only the AC adapter (AW-PS300) designed for

use with this pan-tilt head.

OWhen handling the pan-tilt head, be sure to hold it by the base.

Do not lift the pan-tilt head by the head or tilting arm.

Doing so may cause the unit to malfunction.

ODo not turn the head or tilting arm by hand.

Doing so may cause the unit to malfunction.

ODropping the pan-tilt head or subjecting it to a strong shock may cause malfunctioning or

an accident.

OInstall the pan-tilt head so that a clearance of at least one meter is left around the

monitor.

OWhen mounting a camera onto the pan-tilt head, take due care to prevent the camera

from slipping out of position or dropping.

OInstall the pan-tilt head and set the limiters so as to ensure that none of the components

mounted on the pan-tilt head or cables will make contact with any other objects in the

vicinity when the pan-tilt head rotates.

Precautions for use

This pan-tilt head uses a manganese dioxide-lithium battery (CR2032).

Be absolutely sure to remove this battery when disposing of the pan-tilt head or printed

circuit boards.

Be sure to dispose of any batteries removed according to the applicable regulations of the

country concerned.

Do not dispose of this type of battery as household garbage.

For details on how to remove the battery, refer to the section on replacing the battery in

“Replacement of consumable parts” (page 32).

Parts and their functions

G/L I N Pb OUT Pr /SDI

OUT Y/VIDEO

OUT

1394

CONTROL IN

IP/RP

DC12V

CAMERA I/F

LENSE I/F

ND/EXT

SDI

CSOP

LAMP

CONTROL

;

Parts and their functions

=Safety wire mounting hole

This is used when attaching a wire to

prevent the pan-tilt head from dropping.

>Base connector panel

This is used for connection with a

controller, multi-port hub or AC adapter

for the pan-tilt head.

?Blank side panel

This is used when changing the

mounting position of the base connector

panel.

@Blank bottom panel

This is used when changing the

mounting position of the base connector

panel.

1Tilting arm

This tilts in the vertical direction.

2Tilting arm fixing screws

M4a12 mm (4 screws supplied)

3Camera mounting plate

This is used to mount the convertible

camera.

4Guide screws

These are used to maintain the camera’s

balance and anchor the camera

mounting plate.

5Guide pin

This determines the mounting direction

of the camera.

6Guide roller

This serves as the fulcrum for

maintaining the camera’s balance.

7Camera mounting screws (U1/4˝-20

UNC)

These are used to mount the camera

and anchor it securely.

8Head

This rotates in the horizontal direction.

9Tally lamps (a2)

These light (red) in response to the

selection signals.

:Head connector panel

This is used for connection with the

camera and lens.

;Base

<Pan-tilt head mounting holes

These four holes are used for mounting

the pan-tilt head.

Installation

(The installation work must be performed by your dealer without fail.)

$Assembling the pan-tilt head

Be absolutely sure to hold the pan-tilt head by the base when handling it.

OAttaching the tilting arm

Use the tilting arm fixing screws to attach the tilting arm. The way in which the arm is

mounted differs depending on the direction in which it is installed. (See the figure

below.)

Stand-alone installationSuspended installation

Tilting Arm

<Note>

Do not use other than the supplied tilting arm fixing screws to fasten the tilting arm.

SW3

SW4

OFF

ONSW2

1234

Installation

(The installation work must be performed by your dealer without fail.)

$Setting the installation direction selector switch and landing

characteristics

Set the switches as follows to perform a stand-alone installation and/or to select the

landing characteristics. (Suspended installation and soft landing are the factory

settings.)

1. Remove the four head cover screws, and remove the cover slowly. (Take care not to

disturb the tally LED lamp wiring connections when removing the cover.)

2. Set the SW2, SW3 and SW4 switches on the front printed circuit board as follows.

For suspended installation:

Set SW3 and SW4 to their left-side positions (HANGING). (Factory setting)

For stand-alone installation:

Set SW3 and SW4 to their right-side positions (TOP).

For a soft landing:

Set SW2 switch No.4 to its top (ON) position. (Factory setting)

For a precise landing:

Set SW2 switch No.4 to its bottom (OFF) position.

3. Upon completion of the settings, return the rotary head cover to its original position,

and secure it with the screws (while taking care not to pinch the wires).

<Notes>

OBefore setting the switches, make absolutely sure that the power of the AC adapter

which is to be connected to the pan-tilt head is set to OFF.

OThe landing characteristics are not changed simply by selecting the switch positions.

They are changed only after the power is turned off and back on again after the switches

have been set.

Suspension Stand-alone

This manual suits for next models

Table of contents

Other Panasonic Camera Accessories manuals

Panasonic

Panasonic WV-Q116 User manual

Panasonic

Panasonic HVX200 User manual

Panasonic

Panasonic BQ-BS2E/2E User manual

Panasonic

Panasonic Lumix H-PS14042 User manual

Panasonic

Panasonic UP-RW1245P1 User manual

Panasonic

Panasonic AS09A51 Instruction Manual

Panasonic

Panasonic AW-RC400E User manual

Panasonic

Panasonic AW-LZ17MD9AG User manual

Panasonic

Panasonic AWPH600P - OUTDOOR PAN/TILT HEAD User manual

Panasonic

Panasonic BB-HGW700A - Network Camera Router User manual

Panasonic

Panasonic AW-AD700BS User manual

Panasonic

Panasonic AWPH405N - PAN/TILT CAMERA User manual

Panasonic

Panasonic AW-PB303 User manual

Panasonic

Panasonic WV7260 - CCTV ACCESSORIES User manual

Panasonic

Panasonic POH1000 Operating and installation instructions

Panasonic

Panasonic Videolarm POD9CW User manual

Panasonic

Panasonic DMW-LMC52PP User manual

Panasonic

Panasonic Lumix H-ES045 User manual

Panasonic

Panasonic VIDEOALARM PODV7CWNS/PODV7CPNS User manual

Panasonic

Panasonic AK-HRP150 User manual

Panasonic

Panasonic PDM9 Installation and operation manual

Panasonic

Panasonic Varicam AU-VCVF20G User manual

Panasonic

Panasonic WG-PT100 User manual

Panasonic

Panasonic H-FSQ 14045 User manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions