Panasonic AJ-CA905G User manual

INCOM

MIC

OFF

POWER

BREAKER

NCOM

RCU EXT

PUSH

Operating Instructions

Camera Adapter

Model No. AJ- G

VQT0L67

Before operating this product, please read the instructions carefully and save this manual for future use.

ENGLISHFRANÇAIS

日

本

語

2(E)

$DO NOT REMOVE PANEL COVER BY

UNSCREWING.

To reduce the risk of electric shock, do not remove

cover. No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD AND ANNOYING INTERFERENCE, USE

THE RECOMMENDED ACCESSORIES ONLY.

CAUTION:

Do not install or place this unit in a bookcase,

built-in cabinet or any other confined space in

order to maintain adequate ventilation. Ensure

that curtains and any other materials do not

obstruct the ventilation to prevent risk of electric

shock or fire hazard due to overheating.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, REFER CHANGE OF SWITCH SETTING

INSIDE THE UNIT TO QUALIFIED SERVICE

PERSONNEL.

WARNING:

OTO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS EQUIPMENT

TO RAIN OR MOISTURE.

OTO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, KEEP THIS EQUIPMENT AWAY FROM

ALL LIQUIDS-USE AND STORE ONLY IN

LOCATIONS WHICH ARE NOT EXPOSED TO

THE RISK OF DRIPPING OR SPLASHING

LIQUIDS, AND DO NOT PLACE ANY LIQUID

CONTAINERS ON TOP OF THE EQUIPMENT.

indicates safety information.

For your safety

General

Main Power Battery (Ni-Cd Battery)

Batterij Voor Primaire Voeding (Nikkelcadmiumbatterij)

To remove the battery/Verwijderen van de batterij

Battery/Batterij

(BP-90 type)

Battery/Batterij (BP-90 type) Anton Bauer Battery

Anton Bauer-Batterij

Unlock

Ontgrendelingshefboom

OIf a battery made by any other manufacturer is to be used, check the Operating Instructions accompanying the battery.

OIn geval u een batterij van een anden fabrikant zou gebruiken, gelieve dan eerst zorgvuldig de gebruiksaanwijzing van

deze batterij te lezen.

3 (E)

ENGLISH

indicates safety information.

Operating precaution

Operation near any appliance which generates strong magnetic fields may give rise to noise in the video and

audio signals. If this should be the case, deal with the situation by, for instance, moving the source of the

magnetic fields away from the unit before operation.

For U.S.A.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (service) instructions in the

literature accompanying the appliance.

FCC Note:

This equipment has been tested and found to comply

with the limits for a class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference when the equipment is operated in a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful interference to

radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case the

user will be required to correct the interference at his

own expense.

Warning:

To assure continued FCC emission limit compliance,

the user must use only shielded interface cables when

connecting to external units. Also any unauthorized

changes or modifications to this equipment could void

the user’s authority to operate it.

OBatteries are used for the main power source and memory back-up in the product.

At the end of their useful life, you should not throw them away.

Instead, hand them in as small chemical waste.

OVoor de primaire voeding en het reservegeheugen van het apparaat wordt gebruikgemaakt van een

batterij.

Wanneer de batterij is uitgeput, mag u deze niet gewoon weggooien, maar dient u deze als klein

chemisch afval weg te doen.

Attention/Attentie

ATTENTION:

The product you have purchased is powered by a

nickel cadmium battery which is recyclable. At the

end of it’s useful life, under various state and local

laws, it is illegal to dispose of this battery into your

municipal waste stream.

Please call 1-800-8-BATTERY for information on how

to recycle this battery.

Ni-Cd

RBRC

4(E)

Thank you for purchasing the AJ-CA905G camera adapter (which will be referred to as “the unit” in these

instructions).

Installing the unit on a camera recorder and using a 26-pin multi-cable to connect the camera recorder with a

remote control unit (AJ-RC905) makes it possible to operate the camera recorder as a system camera and

broaden the range of the applications and uses of the camera recorder.

Camera recorders which support the unit:

AJ-SDC615, AJ-SDC905

To ascertain whether any other camera recorders are compatible with the unit, consult your dealer.

Contents

Checking the accessories provided

with the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Parts and their functions . . . . . . . . . . . . . . . . . . . .5

Installing the unit on the camera recorder . . . . . .6

Attaching the battery pack . . . . . . . . . . . . . . . . . . .7

Setting the internal switch . . . . . . . . . . . . . . . . . .11

Connector pin signals . . . . . . . . . . . . . . . . . . . . . .12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Precautions:

OBefore changing the position of the unit’s POWER switch (from RCU to BATT or vice versa), set the camera

recorder’s power switch to OFF.

If the unit is to be used with its POWER switch at the RCU position, be absolutely sure to set the power switch

of the remote control unit (AJ-RC905) to ON first, and then set the camera recorder’s power switch to ON.

OEven when the camera recorder’s power is turned off, the unit’s INCOM (Inter-Communication) circuit will

remain active.

OIf the unit’s power is to be turned off while a battery pack is being used as the camera recorder’s power

source, set the unit’s POWER switch to the RCU position, and then turn off the power of the remote control

unit.

In this case, however, the camera recorder’s LCD display will be cleared.

OThe microphone which is used for INCOM (Inter-Communication) is set to the “carbon type” at the factory.

Since switching to the “dynamic type” requires a change in the position of the internal switch inside the unit,

consult your dealer when putting together your system.

Checking the accessories provided with the unit

NP-1 connector . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Case mounting screws (8 mm) . . . . . . . . . . . . . .4

Connector mounting screws (4 mm) . . . . . . . . .2

5 (E)

ENGLISH

Features

OThe unit can be attached to and removed from the

camera recorder in a single action.

OA battery pack can be selected to serve as the

power source of the camera recorder.

The camera recorder can operate as a regular

camera recorder even while the unit is attached to

it.

OThis unit can be connected to an external VTR

using a 26-pin cable for dubbing.

For details on the signals of the 26-pin cable for

dubbing, refer to page 12.

OThe power is supplied to the camera recorder and

the signals are input and output by a 26-pin multi-

cable (maximum length: 100 meters) in combination

with the remote control unit (AJ-RC905).

The amount of power which can be supplied is

subject to limitations so consult your dealer when

putting together your system.

OThe images being shot by the camera recorder can

be transmitted as analog component signals with

their high image quality intact.

1Battery holder

This is where the battery back is attached.

For details, refer to “Attaching the battery pack.”

2INCOM connector

The INCOM (Inter-Communication) headset is

connected here.

3RCU connector

The remote control unit (AJ-RC905) is connected

here using the 26-pin cable for communications and

signal transmission.

<Note>

When the 26-pin cable is connected, do not apply

excessive force to this connector.

4MIC switch

This is the ON/OFF switch for the INCOM

microphone.

5INCOM dial

This is used to adjust the volume of the INCOM

sounds received.

<Note>

The sound (PGM) of the program being recorded is

multiplexed with the INCOM signals from the

remote control unit (AJ-RC905).

The audio level of the program being recorded is

adjusted using the remote control unit.

6POWER switch

This is used to select the power to be supplied to

the camera recorder.

RCU:

The power to be supplied from the 26-pin cable

(transmitted from the remote control unit) is

selected.

BATT:

The battery pack is selected.

<Note>

If, when a battery pack is used as the power

source, the remaining battery charge has dropped

to the point where the power of the camera

recorder is automatically turned off, all the power

supplied to the camera recorder must be turned off

together.

Set the POWER switch on the camera recorder to

the OFF position, keep the unit’s POWER switch at

BATT, and detach the battery pack.

7BREAKER (circuit breaker) button

When trouble or malfunctioning causes an

excessively high current to flow inside the unit, the

circuit breaker is activated, and the power is

automatically turned off to protect the equipment.

After inspecting and remedying the problem inside

the unit, push this button in.

If there is no trouble or malfunctioning, the power

will come back on.

Parts and their functions

RCU

INCOM

MIC

OFF

POWER

BREAKER

NCOM

RCU BATT

PUSH

6(E)

Installing the unit on the camera recorder

Follow the steps below to install the unit on the camera recorder.

<Note>

With some camera recorder models, the software version may have to be updated. Consult your dealer.

1Check that the unit’s coin screw is up all the way.

If you attempt to attach the unit while the coin

screw is screwed down, you may damage the

connectors.

2Remove the two screws at the rear of the camera

recorder to remove the connector cover.

<Note>

Keep the connector cover and the screws in a safe

place.

3Align the unit’s guides with the battery holders of

the camera recorder, and push it in the direction of

the arrows until it clicks into place.

4Push the coin screw down and tighten it securely.

Coin screw

Screws

Connector cover

7 (E)

ENGLISH

Attaching the battery pack

The power source for the camera recorder on which

the unit is installed can be selected using the unit’s

POWER switch.

When a battery pack is to be used as the camera

recorder’s power source, set the unit’s POWER switch

to the BATT position.

To use the battery pack, there is the following

choice of makes of batteries:

OPanasonic

OAnton-Bauer

OIDX

OPACO

OSony

<Notes>

OFor details on the types of battery packs which can

be used and the settings to be performed after the

battery pack is attached, refer to the operating

instructions of the camera recorder.

OBatteries of other makes can also be supported by

changing the setting menu but no guarantees are

made for the system when they are actually used

with this unit.

OBefore using the battery pack, recharge the battery

using the battery charger.

(For details on the recharging method, refer to the

operating instructions of the battery concerned.)

Anton Bauer battery pack

<Note>

When the battery holder’s power output connector for

lighting is used, use the unit’s power output connector

for lighting. Do not use the camera recorder’s power

output connector for lighting.

<Note>

Intelligent battery systems or ultra-light systems are

not supported.

The remaining battery charge appearing inside the

viewfinder always indicates a voltage level.

1Attach the battery pack made by Anton Bauer.

2To disengage the battery pack, slide it in the

direction of the arrow while the battery holder’s

release lever is kept pulled all the way down.

Battery pack made

by Anton Bauer

Power output connector for lighting

Lighting control switch

Release lever

8(E)

Attaching the battery pack

BP-90 type battery pack

1Remove the battery holder.

2Attach the battery case to the unit.

1Connect the unit’s cable with the cable of the

BP-90 type battery case.

2Use a screwdriver to attach the BP-90 type

battery case to the unit.

The holes for tightening the screws can be seen

when the cover is opened and the rubber caps

are raised. Use a screwdriver to tighten the

screws, and attach the battery case to the unit.

Ensure that the screws are tightened up as far

as they will go.

<Notes>

ODo not pull the rubber caps with great force.

OBe careful not to catch up the cables when

attaching the battery case.

Battery holder

3Connect the plug of the battery pack to the

connector inside the battery case, and insert the

battery pack into the case.

Label surface

<Note>

Before connecting or disconnecting the plug, turn off

the power of the camera recorder.

Connect here. BP-90 type battery

case

9 (E)

ENGLISH

Attaching the battery pack

NP-1 type battery pack

1Remove the battery holder.

2Attach the NP-1 connector provided as an

accessory.

3Attach the NP-1 type battery case to the unit.

1Tighten the case mounting screws (8 mm).

2Tighten the power contact screws.

3Insert the top of the detached cover in the

direction shown by the arrows.

4Align the holes in the bottom of the cover (metal

part) with the holes at the bottom of the case,

and use the screws to attach the case.

<Note>

When mounting the battery case, take care not to

pinch the connecting cord.

Connect here.

NP-1 connector

Connector mounting

screws (4 mm)

Battery holder

10 (E)

Attaching the battery pack

V-mount type battery pack

1Attach the V-mount adapter plate.

2Attach the V-mount type of battery pack.

V-mount adapter

plate.

Table of contents

Languages:

Other Panasonic Camera Accessories manuals

Panasonic

Panasonic WV-Q158C User manual

Panasonic

Panasonic WVPH10 - CL CAMERA ACCESS User manual

Panasonic

Panasonic AWPH405N - PAN/TILT CAMERA User manual

Panasonic

Panasonic AW-LZ17MD9AG User manual

Panasonic

Panasonic HHR370AH User manual

Panasonic

Panasonic CGR18650CG User manual

Panasonic

Panasonic A1 Security Cameras WV-CW4C User manual

Panasonic

Panasonic H-FSQ 14045 User manual

Panasonic

Panasonic LJ-SK56A User manual

Panasonic

Panasonic AG-HVX200AP User manual

Panasonic

Panasonic HHR120AA User manual

Panasonic

Panasonic WV-CS4SA User manual

Panasonic

Panasonic WV-QDC500S User manual

Panasonic

Panasonic VW-CTA1 User manual

Panasonic

Panasonic Lumix H-H014 User manual

Panasonic

Panasonic WV-7130D User manual

Panasonic

Panasonic LC-R061R3P User manual

Panasonic

Panasonic WV-Q152C User manual

Panasonic

Panasonic WV-Q103A User manual

Panasonic

Panasonic AW-PB309P/E User manual

Panasonic

Panasonic DMW-DCC10 User manual

Panasonic

Panasonic WV-Q100A User manual

Panasonic

Panasonic AW-LZ17ST9AG User manual

Panasonic

Panasonic HHR210A User manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions