Optex REDBEAM Series Quick start guide

-1-

• Be sure to thoroughly read the instruction manuals of each product before performing wiring.

• The SIP mounting plate for Gang Box, Gasket sheet for Gang Box, and No. 6-32 UNC screws (5/8 inch) (6 pcs) that are described in PIE-1

Manual are not included in this product as they are not required.

• Up to two detectors can be connected to a PIE-1. (Wire size: at least AWG26 (0.13 mm2), wire length: 2.5 m (8.2 ft.) max.)

BEFORE YOUR OPERATION

ASSEMBLY

No.59-1968-0

Detection range

RBM-60QN-IP

RBM-100QN-IP

RBM-200QN-IP

MODEL

60m/200ft.

350ft.

002 m/650ft.

WIRING DIAGRAM

NETWORK PHOTOELECTRIC DETECTOR

REDBEAM series

™

ø 21mm (0.84 inch) hole diameter

(2) Connect the couduit to the knockout

hole of the back box.

(1) Open the knockout hole (upper or lower)

of the back box.

Step 1

Step 2

Pass the LAN cable

or the external cable

through the grooves

as shown below.

Step 1

Refer to

Step 4

Caution

Be sure to connect the connector after

cutting all the unnecessary wires.

100m/

Back box

PIE-1

Sponge Chassis Main unit Cover

(1) Mount the sponge.

(2) Mount the chassis.

(3) Mount the main unit.

(4) Wire the sensor.

(5)

Connect the alarm 6-pin and power 2-pin cables.

(6) Perform optical adjustment.

(7) Mount the cover.

(2)

(1)

(3)

(4)

Step 3

(1) Plug the alarm 10-pin cable to PIE-1.

(2) Plug the power 2-pin cable to PIE-1.

Use the 24VDC connector.

(3) Set the Selector switch of PIE-1.

(4) Plug the CAT5e cable to the

Ethernet connector for PoE of PIE-1.

(5) Place PIE-1 into the back box.

Upper Lower

Note >>

･Run the cables so that

they are not pinched

between the chassis

and back box.

Banding band

Wiring notch

-2-

(Orange)

(Yellow)

(Green)

(Red)

(Black)

POWER

OUTPUT

24VDC

(Blue)

(Purple)

RECEIVER AND RECEIVER

(1)

(2)

(3)

(4) N.O.

(5) N.C.

(

) COM.

(7)

(8)

(9)

POWERINPUT

10.5-30VDC

SPARE

ALARM OUTPUT

TAMPER OUTPUT

(N.C.)

SPARE

(1)

(2)

(3)

(4) N.O.

(5) N.C.

(

) COM.

(7)

(8)

(9)

POWERINPUT

10.5-30VDC

SPARE

ALARM OUTPUT

TAMPER OUTPUT

(N.C.)

SPARE

Caution

･An alarm output of receiver 2 and purple wire of PIE-1 must be connected inside the back box.

･Make sure that the wires do not contact the terminal block or do not contact each other by cutting unnecessary wires.

･The wiring length other than accessories must be up to 2.5 m. (Wire size: at least AWG26 (0.13 mm2))

･If wiring cannot be secured, use a crimping terminal to secure wiring.

･A PIE-1 can supply power and provide alarm monitoring to up to two detectors.

(1)

(2)

(3)

(7)

(8)

(9)

POWERINPUT

10.5-30VDC

SPARE

TAMPER OUTPUT

(N.C.)

SPARE

(1)

(2)

(3)

(7)

(8)

(9)

POWERINPUT

10.5-30VDC

SPARE

TAMPER OUTPUT

(N.C.)

SPARE

(1)

(2)

(3)

(7)

(8)

(9)

POWERINPUT

10.5-30VDC

SPARE

TAMPER OUTPUT

(N.C.)

SPARE

(Orange)

(Yellow)

(Green)

(Red)

(Black)

POWER

OUTPUT

24VDC

(Blue)

(Purple)

(1)

(2)

(3)

(7)

(8)

(9)

POWERINPUT

10.5-30VDC

SPARE

TAMPER OUTPUT

(N.C.)

SPARE

(1) +

(2)

(3)

(4) N.O.

(5) N.C.

(6) COM.

(7)

(8)

(9)

POWER INPUT

10.5-30VDC

SPARE

ALARM OUTPUT

TAMPER OUTPUT

(N.C.)

SPARE

(Orange)

(Yellow)

(Green)

+ (Red)

(Black)

POWER

OUTPUT

24VDC

(Blue)

(Purple)

(1)

(2)

(3)

(4) N.O.

(5) N.C.

(

) COM.

(7)

(8)

(9)

POWERINPUT

10.5-30VDC

SPARE

ALARM OUTPUT

TAMPER OUTPUT

(N.C.)

SPARE

(Orange)

(Yellow)

(Green)

+ (Red)

(Black)

POWER

OUTPUT

24VDC

(Blue)

(Purple)

RECEIVER ONLY

1TRANSMITTER ONLY

TRANSMITTER AND RECEIVER

3TRANSMITTER AND TRANSMITTER

(Orange)

(Yellow)

(Green)

(Red)

(Black)

POWER

OUTPUT

24VDC

(Blue)

(Purple)

WIRING

Note >>

･The mark on the wiring diagrams indicates that

the wire should be cut off.

･The solid lines on the wiring diagrams indicate provided

cables. For dotted lines, purchase the cable separately.

When connecting the lead wires to the wiring, make the

connection using the connector or soldering. Insert the

wires into the connector and tighten the connections with

pliers.

Connector

(not included)

Note >>

･

For the detector without

back box, tighten the

cables with the banding

band.

This manual suits for next models

Other Optex Security Sensor manuals

Popular Security Sensor manuals by other brands

THORLABS

THORLABS PDA10JT user guide

Waeco

Waeco UV-DETECT operating manual

Intermatic

Intermatic IOS-DSIMF manual

urmet domus

urmet domus 1083 manual

Siemens

Siemens AZL66 Series manual

BTI

BTI Profiline Multi Finder operating instructions

Challenger

Challenger SL01 instruction manual

DMP Electronics

DMP Electronics 1122INT installation guide

Rielta

Rielta Ladoga MK-RK installation guide

Mirion Technologies

Mirion Technologies ACCURAD PRD user manual

Bosch

Bosch DS835 installation instructions

DBI SALA

DBI SALA EZ Stop User instruction manual

Lamptime

Lamptime ST05C instructions

Ubiquiti

Ubiquiti MFI-MSC quick start guide

Subsite

Subsite 910R Support

Satel

Satel OPAL Pro manual

Aleph

Aleph XC-1XTEU manual

Pima

Pima LARIS QUAD installation instructions