OmniPower OPLI-100 User manual
User Manual
Lithium Iron Phosphate
(LiFePO4) Rechargeable Battery
PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE
Product Introduction1
Description
No. Item Description
1 Terminal
Terminal
Terminal
2 Battery Casing
Battery Casing
Compliant to BCI Dimensions.
3 BMS
BMS
4 Battery Cell
Battery Cell
1
1
3
2
4
Charge and discharge wiring port, M8 threaded hole, can directly
replace lead-acid battery application.
Built-in BMS, with overcharge, over discharge, over current, over
temperature, short circuit and other protection functions; support
operation in series (maximum up to 48V). Please refer to "Instruction
for Connecting in Series and Parallel" for more details.
With pouch lithium-ion battery built in, which has the advantages of
high specific energy, high safety, long life, low internal resistance, low
weight and low self-discharge.
1
Specifications
MODEL CAPACITY
(Ah)
12V7Ah 14 151*65*100
12V10Ah 20 151*98*100
12V20Ah 40 181*77*167
12V33Ah 66 196*132*180
12V40Ah 196*166*184
12V75Ah 260*169*227
12V90Ah 307*169*228
12V100Ah 333*172*221
12V150Ah 483*170*241
12V200Ah 522*240*245
7 1.4 7 7F1/F2 N/A
N/A
N/A
N/A
N/A
N/A
Optional
Optional
Optional
N/A
10 2 10 10 F2
20 4 20 20 M5
33 6.6 33 33 M6
40 8 40 40 80 M6
75 15 75 75 200 M6
90 18 90 90 350 M8
100 20 100 100 350 M8
150 30 100 100 350 M8
200 40 100 100 200 M8
• These batteries are mainly used in RV, utility trucks, emergency vehicles, yacht, golf cart, solar
street light, UPS, emergency lighting, alarm system, photovoltaic energy storage, 48V low speed
vehicle and other types of deep cycle lead-acid battery replacement.
• Battery needs to be operated under:
* Acceptable ambient operating temperature:
charging at 0°C~45°C, and discharging at -20°C~55°C
Operating Conditions
CHARGE
CURRENT
(A)
MAX
CHARGE
CURRENT
(A)
MAX
DISCHARGE
CURRENT
(A)
PULSE
CURRENT
(A)
(＜3S)
DIMENSIONS
(MM) TERMINAL BLUETOOTH
2
* Charging voltage is 14.4V
* Ambient humidity: ≤85%
Cautions: Improper use will cause irreversible damage to the battery, and could cause
battery swelling and smoke in extreme cases.
Please follow the vehicle/equipment manufacturer's instructions:
•When replacing various types of deep cycle applications, please ensure the battery capacity is not
less than the original lead-acid battery.
• Please check the battery status before installation:
* Please check the battery voltage with amultimeter. If the battery voltage is less than 13V, please
recharge it (Refer to "Charging Instruction").
*When connecting in series or in parallel, please ensure the capacity and voltage between each
battery is consistent (Refer to "Instruction for Connecting in Series and Parallel").
*Please check the battery to ensure the terminals are clean with no rust, and the screws are clean
without foreign objects.
* Please ensure that the cable connecting the battery terminals is long enough.
* Please ensure that the screws on the terminals are fixed/tightened to the maximum to avoid
loosening during operation.
* Please ensure that the maximum output voltage of the charging device connected to the battery
does not exceed 14.6V before connecting.
Installation Instruction
• Please ensure charging voltage is 14.4V.
•The charging current must not exceed the maximum charging current which is indicated in the
specification sheet in this User Manual.
•The batteries used in series do not need to be disassembled for separate charging, but ensure that
the individual batteries must be fully charged before connecting in series. For details, please see
"Series and Parallel Precautions".
•Please ensure to charge at an ambient temperature of 0°C~45°C. Below 0°C or above 45°C cause
irreversible damage to the battery or even a safety risk.
• You must NOT use a lead-acid battery charger if it has any following mode or function:
Charging Instruction
3
• Please ensure to fully charge each battery before connecting in series or parallel.
•If the battery top cover has alabel showing number 1-N, such as 1-1, 1-2, 1-3, 1-4, that means
the batteries are grouped in manufacturing factory, to ensure the high consistence in case batteries
would be connected in series or parallel. The first number is the group number, and the second
number is the sequence within the group. Please do not mix different groups of batteries.
• The battery can be connected in series up to 4batteries, or in parallel up to 2batteries. Take
12V100Ah for e.g., 4batteries connected in series can create a48V100Ah battery bank; and 2
batteries connected in parallel can create a12V200Ah battery bank. If you want to use them in
series and in parallel at the same time, please contact the dealer for a solution.
* "Equalization mode"
* "Desulfation mode"
* "Pulse function"
•DO NOT leave the lead-acid battery charger connected to maintain or store the battery, because
most will NOT maintain the proper voltage charge algorithm for lithium batteries and damage will
occur to the battery.
• If you want to charge abattery with lead-acid charging system, make sure the charging voltage is
less than 14.6V. If charging batteries in series, make sure the charging voltage is less than 14.6V
times the series number. For e.g., if you want to charge batteries in 4series, the charging voltage
should be less than 58.4V, and the charging current must follow the instruction in “Charging
Instruction”.
• Please do not exceed the maximum discharge current in this User Manual.
•Do not discharge the battery with maximum discharge current several times in succession, since it
may cause battery damage.
•The maximum continuous power for 12V100Ah, 12V150Ah, and 12V200Ah should not exceed
1280W. i.e., they can support 1000W inverter, but the maximum continuous load should not exceed
1100W (according to conversion efficiency 85%).
• Do not mix a new battery and a used battery in a same configuration.
Discharging Instruction
Instruction for Connecting in Series and Parallel
4
•Parallel batteries can only increase the capacity of the battery system and increase the working time
of the connected electrical devices. However, the maximum/peak discharge current can only be in
accordance with asingle battery. For e.g., use four 100Ah batteries configured in parallel to connect
an inverter/motor or other devices, the maximum continuous power cannot be more than 1100W
(according to conversion efficiency of 85%).
12V90/100/150Ah Connecting to Bluetooth2
1. The Bluetooth App is available on Google Play Store and Apple's App Store for download. Install
the App and allow notification on your phone screen.
2. Activate Bluetooth mode on your phone before connecting battery and phone.
Note: Bluetooth is currently only available for 12V90/100/150Ah, more models might be available in
the future.
3. Connect the battery to your phone. You can rename the battery after connecting. There are two
ways for connecting:
1）Search the battery from the device list that your phone can discover.
2）Scan QR code on the battery, and the battery name will appear.
Remark: One smartphone can only connect to one battery at the same time. You need to check
the batteries one by one in turns if you configure them in series or parallel.
5
CONNECT
4) You can rename the battery after being connect-
ed.The connected device will appear in the
history when accessing the App again.
3) Choose the device and connect it:
6
Click to check the Alarm details.
Battery State: Standby/Charging/Discharging
Perfect: >90% Initial Capacity
Good: 80%~90% Initial Capacity
Service: ≤80% Initial Capacity
Battery Voltage (4 cells in series)
The discharge status is indicated by acounterclockwise flowing circle in orange, which is
displayed as anegative value; the charge status is indicated by aclockwise flowing circle in
blue, which is displayed as a positive value.
Time to fully charge
1
2
3
4
5
6
4. After connecting, you can see the SOC (States of Charge) from the Basic Info.
There are 4battery cells in total. If the voltage difference between any two of them reaches or
even is higher than 400mV, these two cells will be displayed in red:
7
i
100.0Ah13.2V
Standby Perfect
6. You can disconnect battery from the connecting device list.
5. You can also check the individial cell voltage from the Details Info.
8
100.0Ah13.2V
Standby Perfect
Note: You can check Manual and other informations from the menu.
9
Contact
Notification
Manual
About
BluetoohDevices
Table of contents
Other OmniPower Camera Accessories manuals
Popular Camera Accessories manuals by other brands
Viltrox
Viltrox EF-NEX Mount instructions
Calumet
Calumet 7100 Series CK7114 operating instructions
Ropox
Ropox 4Single Series User manual and installation instructions
Cambo
Cambo Wide DS Digital Series Main operating instructions
Samsung
Samsung SHG-120 Specification sheet
Ryobi
Ryobi BPL-1820 Owner's operating manual
