Olympus DP26 User manual

INSTRUCTIONS

DP26

MICROSCOPE DIGITAL CAMERA

This instruction manual is for the Olympus Microscope Digital Camera Model DP26.

We recommend that you study this manual thoroughly before operating the camera and familiarize

yourself fully with the use of this camera, which is important to ensure the safety, and to obtain optimum

performance.

Retain this instruction manual in an easily accessible place near the work desk for future reference. AX7970

This device complies with the requirements of both directive 2004/108/EC concerning electromagnetic

compatibility and directive 2006/95/EC concerning low voltage.

In accordance with European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment, this symbol indicates that the product must not be disposed of as unsorted

municipal waste, but should be collected separately.

Refer to your local Olympus distributor in EU for return and/or collection systems available in your

country.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

DP26

CONTENTS

IMPORTANT – Be sure to read this section for safe use of the equipment. – 1-10

1 SYSTEM CHART 10

2 NOMENCLATURE 11

3 INSTALLATION 12-15

4 IMAGE RECORDING PROCEDURE 16,17

4-1 Software.......................................................................................................................................................................................................................16

4-2 Image Recording Procedure.....................................................................................................................................................................17

5 SPECIFICATIONS 18,19

6 TROUBLESHOOTING GUIDE 20-24

PROPER SELECTION OF THE POWER CORD......................................................................................................................25-28

1Intended Use....................................................................4 2PC and Software............................................................4

3Conformity of the System..................................4-8 4Getting Ready..................................................................8

5Maintenance and Storage....................................9

1. Before connecting or disconnecting a connection cable or power cord, make sure that the main switch

of the camera or PC is set to OFF. When connecting a cable or power cord, push in the connector all the

way before pressing the main switch to ON.

2. To avoid electric shock or equipment failure, never connect or disconnect a cable while the main switch

is set to ON.

3. If the main switch of the camera is turned OFF using DP26, PC the application may malfunction. Be

sure not to turn OFF the switch during using DP26.

4. Always use the AC adapter provided by Olympus.

Using a similar but non-Olympus AC adapter does not only allow the camera to manifest its full

performance but may also cause an equipment failure as well as a burn or fire hazard due to abnormal

heating. Never use such an AC adapter.

5. The cords and cables are vulnerable to bend or twist. Do not apply excessive force to them.

Also distribute the cords and cables away from a heat-generating part such as the lamp housing of the

microscope.

The DP26 microscope digital camera is designed to be connected to a camera adapter mounted on an

Olympus UIS2/UIS series microscope for recording of microscopic magnified images.

When the DP26 is used with a camera adapter from other manufacturers than Olympus, the optical

performance may not be fully manifested.

IMPORTANT

Safety Precautions

DP26

Safety and Operation Symbols

The following symbols are found on the camera. Study the meaning of the symbols and always use the

equipment in the safest possible manner.

Symbol Explanation

Indicates a non-specific general hazard. Follow the description given after this symbol

or in instruction manual.

　,　Indicates “ /” (ON) or “ \” (OFF) of the main switch.

Use the specified AC adapter (6 V, 2.5 A DC)

Symbol of camera cable (1394) connector.

6. To prevent the microscope from toppling down, avoid using microscope attachments that may make the total

height of the microscope above 1 meter when they are attached.

7. The AC adapter and camera generate heat after they have been used for a long period of time.

To avoid moderate temperature burn, do not leave these parts in extended contact with your skin.

8. Connect the power cord correctly and ensure that the grounding terminals of the power supply and wall outlet

are properly connected. If the equipment is not grounded properly, Olympus can not warrant the electrical

safety performance of the equipment.

9. Sharp edges inside the computer may cut your fingers, so take extra care.

If the equipment is used in a manner not specified in this manual, the safety of the user may be imperiled. In

addition, the equipment may also be damaged. Always use the equipment as outlined in this instruction manual.

The following symbols are used to set off text in this instruction manual.

: Indicates a potentially hazardous situation which, if not avoided, may result in minor

or moderate injury or damage to the equipment or other property. It may also be

used to alert against unsafe practices.

? : Indicates commentary (for ease of operation and maintenance).

The recorded image data may be lost (destroyed) in the following cases. Note that Olympus will

not assume any liabilities for the loss (destruction) of recorded data.

The image data may also be destroyed by an unexpected cause. It is recommended to back up

the data periodically.

•When the user or a third party services or repairs the equipment.

•When the PC is shut down, the AC adapter is disconnected or the power cord is unplugged

during recording or erasure (formatting) of the PC.

•When the equipment fails.

Before disposing of this product, be sure to follow the regulations and rules of your local government.

Caution

Note on Disposal

Caution on Image Data Storage

DP26

2PC and Software

1Intended Use

This device is intended to be used for the capture of digital images for non-clinical diagnostic purposes.

1. Olympus will not assume any liabilities for any damage due to the use or non-usability of this system,

including compensation for the lost data.

2. When the HDD free space reduces, the data processing speed may slow extremely or errors may occur

frequently. To prevent this, delete unnecessary data files frequently.

3Conformity of the System

•The 1394 driver specialized for DP26 must be installed to operate DP26. When this driver is installed,

other 1394 devices except Olympus Digital Camera for Microscope cannot be operated though

connected. (Note that DP 25 cannot be used.)

•The 1394 driver can be installed at the same time when installing DP2-TWAIN or cellSens.

•To connect other 1394 devices, the driver specialized for DP26 must be uninstalled. (When the driver

specialized for DP26 is uninstalled, DP26 cannot be operated.)

•When connecting the DP26 to the PC, connect the DP26’s camera head directly to the 1394 connector

of the PC. Connection through a commercially available 1394 hub or conversion connector may lead to

malfunction.

When using desktop PC or laptop PC

Device driver

Common to Desktop PC/Laptop PC (except No. 7)

No. Item Operating Environment

1 PC Intel Pentium 4, Intel Xeon or Intel Core Duo (or equivalent)

2 Memory Windows®7, WindowsVista®:2 GB or more (3 GB or more recommended)

Windows®XP：1024MB RAM

3 HD space 1 GB (before installation)

4 PC monitor 1280 x 1024 recommended (1024 x 768 or more), 32-bit video card

5 Drive DVD-ROM drive

6 USB Protection key port x 1

7 1394 1394a port x 1

•Desktop PC: 9-pin 1394b port or 6-pin 1394a port

•Laptop PC: 4-pin 1394a port (The AC adapter should be connected to

the camera head)

8 PC input devices 2-button mouse or 3-button mouse, (Wheel-equipped model recommen-

ded)

Keyboard

9 OS Windows®7 Ultimate / Professional (32bit / 64bit)

Windows Vista®Ultimate / Business (32bitSP2)

Windows®XP Professional (SP3 or after)

10 OS languages Japanese, English

11 Web browser IE6.0 or after

The fact that the recommended operating environment above is met does not necessary guarantee the

availability of all of the operations that are usually available with the PC connection system.

Recommended operating environment

DP26

Windows®is a registered trademark of Microsoft Corporation, USA.

All of other brand names and product names mentioned in this manual are trademarks or registered trademarks

of their respective owners.

Trademark information

Windows®7, Windows Vista®

Installation is impossible unless your user account is registered as a “Computer Administrator account.”

If you are registered in the “Standard user account,” please change it to the “Computer Administrator

account.” (For the user account registration, refer to the manuals for your PC.)

Windows®XP

Installation is impossible unless your user account is registered as a “Computer Administrator account.”

If you are registered in the “Restricted account,” please change it to the “Computer Administrator account.”

Before installation

Restrictions in Use

1. The standard TV adapters are the U-TV1XC and U-TV0.63XC.

The U-TV0.25xC, U-TV0.35xC (or a TV adapter with magnification below 0.5X), U-TV0.5XC and GX-TV0.5XC-

DP cannot be used because of optical performance problems.

2. When two or more intermediate attachments are used, the peripheral part of the image may become

dark or obscured depending on the observation tube and objective in use.

3. When a fluorescent lamp illumination or an illumination stand of the SZX/SZX2 series is used, the image

may flicker.

4. Combinations of this product and non-Olympus microscopes have not been evaluated extensively.

Non-Olympus microscopes and commercially available C-mount lenses can be used provided that

they match a CCD with a size of no less than 2/3 inch and the lens projection length from the C-mount

body attaching section is no more than 6 mm. However, problems due to optical adaptability, such as

shading, may be observed.

5. When the specimen has a low contrast (near transparent) or high reflectance (mirror status) and the

aperture iris diaphragm is stopped near the smallest aperture, spot flare may be noticeable.

6. There are some cases that red flare appears in the image of specimen which has very big differences

in luminance, and the strong luminance portion is located in the image. This results from the peripheral

surface reflection of the CCD. This flare can be minimized by adjusting the exposure for strong

luminance portion to appropriate level, or by opening the AS.

7. When the edge of a non-transmitting object is observed by transmitted illumination under the STM6

in combination with the MM6-OB3X/5X/10X objective and the MM6C-VL/MM6-ETR, flare may be

noticeable due to the difference in brightness between the transmitted sections (over-exposure) and

non-transmitting section (underexposure).

To reduce the flare, set a lower exposure using the exposure adjustment function or setting the exposure

manually.

8. The image of dark specimens under reflected light or in the darkfield (specimens that need exposure of

1/2 sec. or more at ISO 100 equivalent) cannot be recorded.

9. Specimens with a distribution that is not suitable for center averaged metering require spot metering or

exposure adjustment.

10. When electronic zoom is used for magnification display during focusing, the image may become

noticeably coarse with certain samples.

Other manuals for DP26

Table of contents

Other Olympus Microscope manuals

Popular Microscope manuals by other brands

Thermo Scientific

Thermo Scientific Nicolet iN10 Using

National

National DC3-163 instructions

KERN Optics

KERN Optics OPE-1 User instructions

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Operation manual

Prior

Prior Lux POL operating instructions

Opitec

Opitec Smartscoop 115615 instructions

KERN

KERN OPO-1 operating instructions

Topcon

Topcon SP-1P user manual

Motic

Motic PA43 Operation manual

Leica

Leica DVM5000 Setup manual

MshOt

MshOt MZ62 user manual

KERN Optics

KERN Optics OZR-5 User instructions

VWR

VWR VisiScope 384 Series instruction manual

Nikon

Nikon ECLIPSE E200 POL instructions

Leica

Leica DI C800 User's manual & installation instructions

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

Leica

Leica FL560 user manual