Olympus CX33 User manual

INSTRUCTIONS

This instruction manual is for the Olympus biological microscope.

To ensure the safety, obtain optimum performance and to familiarize yourself fully with the use

of this microscope, we recommend that you study this manual thoroughly before operating this

microscope, and always keep this manual at hand when operating this product.

Retain this instruction manual in an easily accessible place near the work desk for future

reference.

Biological Microscope

CX33

AX 8881

Optical Microscope and Accessory

In accordance with European Directive on Waste Electrical and Electronic Equipment, this

symbol indicates that the product must not be disposed of as unsorted municipal waste, but

should be collected separately.

Refer to your local Olympus distributor in EU for return and/or collection systems available in

your country.

NOTE: This product has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the product is operated in a commercial environment. This product

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications.

Operation of this product in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the product.

For Korea only

B급 기기 (가정용 방송통신기자재)

이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을

목적으로 하며, 모든 지역에서 사용할 수 있습니다.

Safety precautions ....................................................................................................................................... 1

1 Standard combination......................................................................................................................... 5

2 Nomenclature of operating portions ...................................................................................... 6

3 Outline of brightfield/darkfield observation methods ............................................. 7

4 Observation procedures .................................................................................................................... 9

1 Turning ON the LED illumination ......................................................................................................................................9

2 Selection between the eyepiece light path and the camera light path .....................................9

3 Placing the specimen ............................................................................................................................................................10

4 Selecting the objective ..........................................................................................................................................................14

5 Focusing on the specimen ................................................................................................................................................14

6 Adjusting the interpupillary distance ........................................................................................................................15

7 Adjusting the diopter. ..............................................................................................................................................................16

8 Adjusting the aperture diaphragm (AS) ................................................................................................................17

9 Attaching the darkfield ring slit (for darkfield observation only) .......................................................17

10 Acquiring the image with the camera .....................................................................................................................18

11 Using the 100X oil immersion objective ................................................................................................................19

5 Glossary of optical performance terminology .............................................................21

6 Troubleshooting ......................................................................................................................................23

7 Specifications ............................................................................................................................................25

8 List of optical performances ........................................................................................................26

Contents

9 Assembly .......................................................................................................................................................27

9-1 Assembly diagram ......................................................................................................................................... 27

9-2 Assembly procedures ................................................................................................................................. 28

1 Removing the standard 10X eyepiece ....................................................................................................................28

2 Attaching the eyepiece micrometer ..........................................................................................................................28

3 Attaching the eyepieces (Standard 10X eyepieces or WHSZ15X-H) ...........................................29

4 Attaching the objective CXPL20X or CXPL100XO .......................................................................................29

5 Attaching the specimen holder CX3-SHP or CX3-HLDT .........................................................................30

6 Attaching the camera adapter U-TV1XC and the camera .....................................................................30

7 Attaching the filter holder CH2-FH and darkfield ring slit CH2-DS ..................................................31

8 Attaching the filter of 45mm in diameter ..............................................................................................................31

9 Connecting the AC adapter and power cord ...................................................................................................32

10 Attaching the allen wrench holder .............................................................................................................................33

CX33

If the product is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the

product may also be damaged. Always use the product according to this instruction manual.

The following symbols are used in this instruction manual.

CAUTION : Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury.

NOTE

: Indicates a potentially hazardous situation which, if not avoided, may result in

damage to the product or other property.

TIP

: Indicates the useful knowledge or information for use.

CAUTION - Installation of the product -

Wear protective equipment such as gloves, etc.

When you observe the specimens which have potentiality of infection, wear protective equipment such as gloves, etc.

to prevent the specimens from touching your skin directly.

When you maintain the product which may have contacted the specimens which have potentiality of infection, wear

protective equipment such as gloves, etc., or clean the product before operation.

After observation, clean the portions where specimens contacted directly.

Remove the specimen when moving the product.

When moving this product, be sure to remove the specimen first, since it is in danger of dropping and spattering.

In case the specimen is damaged, promptly take the infection prevention measures.

When disposing of the product, follow the regulations and rules of your local government.

When disposing of the product which contacted the specimens which have potentiality of infection, follow the

regulations and rules of your local government.

Install the microscope on a sturdy, level table or bench.

For safety in particular, do not place a mat, etc. under the product.

CAUTION - Light from the objective -

Do not look directly at the light coming out from the objective or the light reflected from the specimen.

Be careful about the light coming out from the objective, since not only visible light but also light of invisible

wavelengths (such as ultraviolet and infrared) may be emitted depending on the illumination methods.

Safety precautions

CAUTION - Prevention of infection -

CAUTION - Electric safety -

Always use the AC adapter and power cord provided by Olympus.

If the proper AC adapter and the power cord are not used, the electric safety and the EMC (Electro-Magnetic

Compatibility) performance of the product cannot be assured. If no power cord is provided, please select the proper

power cord by referring to the section “Proper selection of the power cord” at the end of this instruction manual.

Always connect the ground terminal.

Connect the ground terminal of the power cord and that of the power outlet. If the product is not grounded, our

intended electric safety and EMC performance of the product cannot be assured.

Do not use this product near the sources of strong electromagnetic radiation.

Proper operation may be interfered. Be sure to evaluate the electromagnetic environment before operating the product.

Disconnect the power cord in case of emergency.

In case of emergency, disconnect the power cord from the power cord connector of the product or from the power

outlet.

Install the product at the location where you can reach the power cord connector or the power outlet with your hand to

disconnect the power cord immediately.

This product complies with the emission and immunity requirements described in IEC61326 series.

CAUTION - LED (light emitting diode) -

Do not look directly at the light from LED for a long time.

If you feel that the light from LED is too bright during observation, adjust the light intensity using the brightness

adjustment knob before continuing the observation. The LED built in this product is basically eye-safe. However, do not

look directly at the light from LED for a long time while feeling too bright, since it may cause damage to your eyes.

CAUTION - Safety symbols -

The following symbols are attached to the product.

Study the meaning of the symbols and always use the product in the safest possible manner.

Symbol Meaning

Indicates a non-specific general hazard. Follow the description given after this symbol

or in the instruction manual.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

CX33

1. Be careful not to apply the impact or let the dirt/dust attached to the microscope when carrying it.

2. Do not use the product in areas where it may be subjected to direct sunlight, high temperature and/or humidity, dust or

vibrations. (For conditions of operating environments, see “7 Specifications” on page 25.)

3. When installing the microscope, assure sufficient space around the microscope.

4. When carrying this microscope, disconnect the AC adapter from the microscope, and store the AC adapter and the power

cord in the microscope frame. Then, hold both sides of the arm as shown in the lower left picture, and carry it carefully. Then,

hold both sides of the arm a as shown in the picture on the left, and carry it carefully. (For procedures to store the AC

adapter and the power cord, see “Storing the AC adapter and power cord” on page 32.)

Handling precautions

·This product is a precision instrument. Handle it with care

and avoid subjecting it to a sudden or severe impact.

·Never disassemble any part of the product. Otherwise,

failure could be caused.

·The objectives are screwed in tightly to prevent them from

being loosened during transportation. When removing the

objective, rotate it in the arrow direction as shown in the

picture on the left using the slip prevention rubber sheet,

etc.

·Be sure to use the specified objectives (objectives

provided with the microscope frame and CX-Plan series).

If incorrect objectives are combined, the performance

cannot be delivered.

·The tube of this microscope is removable, but do not

attach the tube of other microscopes.

NOTE

·Do not hold the stage b or the tube c, since they may

be damaged.

·When carrying the microscope, be sure to remove the

specimen and filters in advance, since they are in a risk of

falling. Also, be careful not to touch the objective.

·Do not carry the microscope keeping the AC adapter

connected to the microscope. The AC adapter or the

microscope may be damaged by hitting the output

connector of the AC adapter.

·When carrying the microscope, be careful not to touch the

objective.

NOTE

1. Do not leave stains or fingerprints on the lenses and filters. If they get dirty, blow away dust with a commercially

available blower and gently wipe the lens or filter with a piece of cleaning paper (or clean gauze). Only when cleaning

fingerprints and oil stains, slightly moisten a piece of cleaning paper with commercially available absolute alcohol

and wipe them off with it.

Since the absolute alcohol is highly flammable, it must be handled carefully. Be sure to keep it away

from open flames or potential sources of electrical sparks. For example, the electrical equipment that

is switched ON and OFF may cause the ignition of a fire. Also, always use absolute alcohol only in a

well-ventilated room.

2. Wipe the portions other than the lens with a dry soft cloth. If the dirt cannot be removed by dry-wiping, moisten a soft

cloth with diluted neutral detergent and wipe the dirty surface with it.

Do not use organic solvents because they may deteriorate the coated surface or plastic parts.

3. After using this product, store it in a dry place or cover it with a dust cover. If you need the dedicated dust over (made

by Olympus), contact Olympus.

Do not use a highly sealable cover, such as a plastic bag, etc. as a dust cover. The humidity in the

microscope may increase to damage the product.

4. When disposing of this product, be sure to follow the regulations and rules of your local government. Contact Olympus

for any questions.

CAUTION

NOTE

Maintenance and storage

Intended use

This product has been designed to be used to observe magnified images of specimens in various routine work and

research applications.

This includes the observation of living cells or of specimen taken from tissues to gain physiological or morphological

information at hospitals or laboratories. Typical field of applications are genetics, human blood and tissue examination,

neurology, pharmacology and cellular biology.

Do not use this instrument for any purpose other than its intended use.

This product complies with the requirements of directive 98/79/EC concerning in vitro

diagnostic medical devices. CE marking means the conformity to the directive.

This product is applied with the requirements of EMC standard IEC/EN61326-2-6 and

IEC/EN61326-1 concerning electromagnetic compatibility.

This product complies with the emission and immunity requirements described in IEC61326

series. The electromagnetic environment should be evaluated prior to operation of this product.

CX33

1 Standard combination

Refer to the drawing below and make sure that all necessary units are included in the product you purchased.

Option units

Eyepieces

Revolving nosepiece

Stage

Tube

Power cord

AC adapter

· Eyepiece (2 pieces)

WHSZ15X-H

· Filter holder

CH2-FH

· Darkfield ring

CH2-DS

· 20X objective

100X objective

· Eyepiece micrometer

(Ø24mm, Thickness: 1.5mm)

· Ø45mm filter

· Camera adapter

U-TV1xC

· Camera

DP22 or DP27

· Specimen hold plate · Specimen holder

CX3-SHP CX3-HLDT

Objective

Microscope

frame

Condenser

2 Nomenclature of operating portions

Y-axis knob

Revolving nosepiece

X-axis knob

Light path selection knob

Aperture diaphragm lever

Specimen holder

Brightness adjustment knob

(The filter of 45mm in

diameter can be inserted.)

Diopter adjustment rings

Binocular portion

Diopter adjustment rings

Aperture diaphragm lever

X-axis knob

Brightness adjustment knob

(The filter of 45mm in

diameter can be inserted.)

Specimen holder

Light path selection knob

Filter

Filter holder

(For darkfield observation)

Coarse focusing knob

Specimen holder

fixing knobs

Coarse focusing knob

Fine focusing knob

Main switch

: Power is ON.

: Power is OFF.

Main switch

Y-axis knob

Fine focusing knob

X-axis knob

Y-axis knob

Pre-focusing lever

Tension adjustment ring

Coarse focusing knob

Fine focusing knob

Binocular portion

Table of contents

Other Olympus Microscope manuals

Popular Microscope manuals by other brands

Thermo Scientific

Thermo Scientific Nicolet iN10 Using

National

National DC3-163 instructions

KERN Optics

KERN Optics OPE-1 User instructions

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Operation manual

Prior

Prior Lux POL operating instructions

Opitec

Opitec Smartscoop 115615 instructions

KERN

KERN OPO-1 operating instructions

Topcon

Topcon SP-1P user manual

Motic

Motic PA43 Operation manual

Leica

Leica DVM5000 Setup manual

MshOt

MshOt MZ62 user manual

KERN Optics

KERN Optics OZR-5 User instructions

VWR

VWR VisiScope 384 Series instruction manual

Nikon

Nikon ECLIPSE E200 POL instructions

Leica

Leica DI C800 User's manual & installation instructions

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

Leica

Leica FL560 user manual