Olympus PPO-E02 User manual

取扱説明書

PT-Eシリーズ用防水レンズポート

Instruction Manual

Underwater Lens Port for the PT-E Series

Mode d’emploi

Port d’objectif étanche pour la série PT-E

Bedienungsanleitung

Unterwasser-Objektiv-Port für PT-E Serie

Manual de instrucciones

Puerto de objetivo hermético para la serie PT-E

PPO-E02

PPO-E02Jn05.5.317:21PMページ1

E-1

WARNING

Disclaimer

■ Unauthorized copying of this manual in part or in full, except for personal use, is prohibited. Unauthorized

reproduction is strictly prohibited.

■ Olympus shall not be responsible for damages, loss of profit or any claims by third parties in case of any

damage occurring from incorrect use of this product.

IMPORTANT - Please read the following before using the product

■ This product has been designed to be used underwater at depths up to 60 meters (200 ft). Handle this

product with care.

■ This product must always be used in combination with an applicable lens. Do not combine this product

with an inapplicable lens.

■ To ensure correct and safe use of this product, always use it as described in this instruction manual.

For safe use

This instruction manual uses pictographs to show how to use the product correctly and how to prevent danger to the

user and other persons as well as damage to property. These pictographs and their meanings are shown below.

Please pay particular attention to this information. If ignored when using

the product, there is a risk of serious injury and even death.

WARNING

Ignoring this information when using the product could lead to injury or

material damage.

CAUTION

●

This product should be kept out of reach of infants and children to prevent accidents such as the following:

•

Injury caused by the product falling from a height and striking the body from a height.

•

Injury caused by the swallowing of small parts. Please consult a doctor immediately if this happens.

●

This product is partly made of glass. If it is broken or smashed by being dropped or hit against a hard

object, glass splinters could cause injury. Please handle this product carefully.

●

If water gets into this product during underwater use, immediately stop using it, remove the moisture from

the product and detach it from the camera and lens.

●

Do not disassemble or modify this product. This may result in injury.

●

The silicone O-ring grease is not edible.

CAUTION

●

Do not expose this product to high temperatures for extended periods. This may lead to deterioration of the

product’s components.

●

When mounting this product on the PT-E series waterproof case, be sure to follow the steps described in

this manual.

●

Before detaching this product from the PT-E series waterproof case, make sure that the case is completely

dry and free of moisture.

●

Never attach or detach this product in locations where there is a lot of sand, dust or dirt. If any foreign mat-

ter gets on the O-ring sections, the waterproof sealing will be compromised and water leakage may result.

●

This product has been designed and manufactured for use in a water pressure equivalent to a depth of 60

meters (200 ft). Please note that diving in depths over 60 meters may cause irreparable damage and/or

may result in water leaking into this product and the camera and lens.

●

When sealing this product, make sure that no foreign matter is caught on the O-rings or O-ring contact surfaces.

●

Before storing this product, always remove it from the camera and lens.

●

To control lens zooming from this product, the provided zoom gear must be attached to the zoom ring of the

lens. Correctly attach the zoom gear to the zoom ring of the lens as instructed in this manual.

■ Thank you for buying this product. To assure safe and correct use of this product, please read this instruc-

tion manual carefully. After reading, store the manual together with the warranty card in a safe, easily

accessible place.

■ This product is the Waterproof Lens Port (PPO-E02) designed exclusively for use with the PT-E series of

waterproof case.

■ Underwater zooming is made possible by attaching the zoom gear, provided with this product, to the zoom

ring of an applicable camera lens.

PPO-E02En05.5.317:34PMページ1

E-2

PPO-E02 main body

Silicon O-ring (POL-E101)

Front cap

Rear cap

Zoom gear

Grease for silicone O-ring

Pick for O-ring removal

1Name of Parts

2Mounting the PPO-E02 on the Waterproof Case

Port mount thread

O-ring contact surfaces

O-ring

Threaded

section

Grease applying surface on O-rings

This section describes how to mount

this product on the PT-E series case.

Before mounting, check that no for-

eign matter is attached to the O-rings,

the port mount thread on the PT-E

series case, or the O-ring contact sur-

faces. Apply a thin layer of the provid-

ed silicone O-ring grease.

Align the threaded section of the PPO-E02 with the port mount thread on the PT-E series case.

Hold the PT-E series case firmly with one hand, hold the main body of the PPO-E02 with your other

hand and screw it into the PT-E series by turning the PPO-E02 clockwise.

Resistance increases as the PPO-E02 is screwed in more deeply. However, be sure to screw it in all the

way until there is no gap visible below the threaded section of the PPO-E02.

Screw in until

there is no gap.

PPO-E02En05.5.317:34PMページ2

3Dismounting the PPO-E02

If any water is on the product, wipe it completely away and

make sure that the product is dry.

CAUTION:･While dismounting the PPO-E02 from the case, water remaining on the PPO-E02 may splat-

ter on the lens or camera. If this happens, wipe the water off the lens and camera with a dry

cloth.

･Make sure that the port is completely dry before dismounting.



Holding the PT-E series case firmly with one hand, loosen the

PPO-E02 by turning it about 90 degrees counterclockwise. If

the PPO-E02 is attached too tightly to turn, wrap it with a piece

of rubber or similar non-slip material.

After loosening the PPO-E02, point its lens downward and

turn it further counterclockwise until it is separated from the

PT-E series case. Be careful not to drop the PPO-E02 or

PT-E series case.

E-3

PPO-E02En05.5.317:34PMページ3

E-4

4Attaching the Zoom Gear on the Lens

Turn the zoom ring of the lens so that the correct number

(see the following table) is aligned with the zoom index.

Check the position of the lock dial’s hinge on the zoom gear,

then turn the lock dial counterclockwise to release the lock

and open the gear.

Hinge

Open

Lock dial

Open the zoom gear wide and align its hinge with the zoom

index on the lens. Place the zoom gear on the lens and

adjust the rotation direction of the zoom gear. At this time,

bring the gear section of the zoom gear to the left of the

hinge as shown in the illustration.

Set the front-rear direction of the zoom gear by aligning the

edge of the hinge with the end of the rubber section on the

lens’ zoom ring.



After positioning the zoom gear, place it against the lens’s

zoom ring (taking care not to displace the zoom gear), and

turn the zoom gear’s lock dial all the way clockwise to lock it.

Push the gear with a finger

to place the gear against

the lens.

Tu rn the lock dial

to lock the zoom

gear.

To control zooming of the camera lens, the provided zoom gear must be attached to the zoom ring of the lens.

CAUTION: Ifthezoomgearisturnedinthewrongdirectionoritsfront-rearorientationisincorrect,

zoomingcannotbecontrolledproperly.Besuretoattachthezoomgearcorrectly.

Align the hinge

with the index.

Gear

Corresponding lens

Number to align with

the zoom index

ZUIKO DIGITAL 14-54mm F2.8-3.5 25

ZUIKO DIGITAL 11-22mm F2.8-3.5 14

PPO-E02En05.5.317:34PMページ4

Screw the camera table provided with the PT-E

series case firmly into the bottom of the cam-

era.

5Loading the Camera and Lens

After attaching the zoom gear to the camera lens, insert the camera and lens into the PT-E series case on

which the PPO-E02 is mounted.



Remove the eyecup from the camera’s viewfind-

er. If a lens cap or filter is attached to the lens or

the strap is attached to the camera, remove them

as well.

Lift the PT- E series case’s power switch dial,

mode dial knob and zoom dial, and turn the

case’s camera table lock lever counterclock-

wise to release the lock. Refer to the PT-E

series case’s instruction manual for instructions

of how to attach the hot shoe cable for the

flash.

Zoom dial

Mode dial knob

Power switch dial

Camera table lock lever

Confirm that the camera’s power switch is OFF.

Align the correct zoom value for the lens with

the zoom index of the lens. While pulling out

the zoom dial on the PT-E series case, slide

the camera table with camera attached as far

as it will go into the camera table mount on the

inner side of the case’s front lid.

Pull out the zoom

dial further.

E-5

PPO-E02En05.5.317:34PMページ5

E-6



After inserting the camera, turn the PT- E series

case’s

camera table lock lever all the way clock-

wise to lock the camera table. Then, push in the

zoom dial on the case and engage it with the

zoom gear attached to the lens. Turn the zoom

dial to confirm that it can control zooming.

Push in the PT- E series case’s power switch

dial and mode dial knob. Turn the power switch

dial and mode dial knob and confirm that they

can control the camera power ON-OFF and

mode switching. Connect the hot shoe mount

section of the hot shoe cable that has been

connected to the PT-E series case to the hot

shoe of the camera.

Attach the rear lid of the PT- E series case and

lock the four buckles (two diagonally located

buckles first, and then the other two diagonally

located buckles). Underwater shooting is now

possible.



PPO-E02En05.5.317:34PMページ6



After shooting, remove the inserted cam-

era and lens, then re-seal the empty

case and immerse it in tap water to

remove any salt as soon as possible.

6Maintenance

For safe use of this product, always perform maintenance after each diving session.

For details, refer to “Handling After Shooting” and “Maintaining the Waterproof Function” in the PT-E series

case instruction manual. Apply the same procedures to this product.

Remove the O-rings from this product

using the provided pick for removing

O-rings. Take care not to damage the

O-rings.

If any foreign matter is attached to the

O-ring grooves, remove it using a

clean, lint-free cloth or cotton swab.

Also remove any foreign matter from

the O-ring contact surfaces and from

the port mount thread on the PT-E

series case.

After making sure that the PT-E series

case is completely dry, dismount this

product from the case.



Remove sand and dust from the O-rings.

Pinch each O-ring between your fingers

and lightly rub the entire circumference

to check for foreign matter, scratches

and cracks.



After removing foreign matter, apply the

provided grease to the O-rings and fit

them into the O-ring grooves.

To apply grease to each O-ring, squeeze

a drop of grease about the size of a

grain onto your finger and lightly rub the

entire circumference of the O-ring to

spread the grease thinly and evenly.

E-7

PPO-E02En05.5.317:34PMページ7

E-8

Description

O-ring for use with the PT-E series case.

Applicable case : PT- E series

Applicable lens : ZUIKO DIGITAL 14-54mm F2.8-3.5/ZUIKO DIGITAL 11-22mm F2.8-3.5

Main materials

Main body : Aluminum.

Lens window : Chemically reinforced glass.

O-rings : Silicon rubber.

Zoom gear : Polycarbonate resin.

Front cap : NBR rubber.

Rear cap : Polyethylene resin.

Withstanding pressure : Water depth of 60 m (200 ft)

Dimensions : Max. diameter 143 mm x Depth 105 mm

Weight : 650 g (excluding the conversion lens)

7Specifications

Note) We reserve the right to change the external appearance and specifications without notice.

8Consumable Items

This product uses the following consumable items.

Product Model

POL-E101

■ Silicon O-rings

Description

Grease for O-rings

Product Model

PSOLG- 1

■ Grease for silicone O-ring

Shinjuku Monolith, 3-1 Nishi Shinjuku 2-chome, Shinjuku-ku, Tokyo, Japan

Two Corporate Center Drive, Po Box 9058, Melville, NY 11747-9058, U.S.A.

Tel. 631-844-5000

Technical Support (USA)

24/7 online automated help: http://www.olympusamerica.com/support

Phone customer support: Tel. 1-888-553-4448 (Toll-free)

Our phone customer support is available from 8 am to 10 pm

(Monday to Friday) ET

E-Mail: [email protected]

Olympus software updates can be obtained at:

http://www.olympus.com/digital/

European Technical Customer Support:

Please visit our homepage http://www.olympus-europa.com

or call our TOLL FREE NUMBER* : 00800 - 67 10 83 00

Premises : Wendenstrasse 14-18, 20097 Hamburg, Germany

Tel: +49 40-23 77 3-0 Fax: +49 40-23 07 61

Goods delivery : Bredowstrasse 20, 22113 Hamburg, Germany

Letters : Postfach 10 49 08, 20034 Hamburg, Germany

For all not listed European Countries and in case that you

can’t get connected to the above mentioned number please

make use of the following

CHARGED NUMBERS:

+49 180 5 - 67 10 83 or +49 40 - 237 73 899

Our Technical Customer Support is available from 9am to 6pm MET

(Monday to Friday)

for Austria, Belgium, Denmark, Finland, France, Germany,

Italy, Luxemburg, Netherlands, Norway, Portugal, Spain,

Sweden, Switzerland, United Kingdom

*Please note that some (mobile) phone services/ provider do

not permit access or request an additional prefix to +800

numbers.

PPO-E02En05.5.317:34PMページ8

PPO-E02_01Printed in Japan

PPO-E02Jn05.5.317:21PMページ10

Other manuals for PPO-E02

Table of contents

Other Olympus Camera Accessories manuals

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Starlite

Starlite OctoDome nxt instructions

Custom Brackets

Custom Brackets Digital PRO-M Instructions for use