Olympus FC-WR IM012 User manual

取扱説明書

INSTRUCTIONS

MODE D’EMPLOI

INSTRUCCIONES

BEDIENUNGSANLEITUNG

사용설명서

CHT 94

คําแนะนําการใชงาน

108

CÁC HƯỚNG DẪN

122

Model No.: IM012

Thank you for purchasing this Olympus product.

To ensure your safety, please read this instruction manual carefully before use.

In addition, please keep the manual handy for future reference.

Be sure to read the instruction manuals for the ﬂash and the wireless receiver as

well.

If you use the product outside the country or region of purchase, you may violate

local regulations. Olympus accepts no liability in this case.

Checking the Contents of the Package

Pouch

Instructions (This manual)

Wireless radiowave commander:

FC-WR

Warranty card

Names of Parts

1Group buttons (A/B/C) .................. P. 24

2MODE button ................................ P. 25

3TEST button.................................. P. 24

4Control panel ................................ P. 19

5ON/OFF button ............................. P. 22

6Battery compartment cover........... P. 20

7 OK button...................................... P. 24

8Latch release button ..................... P. 21

9Latch ............................................. P. 21

Dial/Arrow pad

0Dial.......................................... P. 24, 27

a a(ﬂash compensation/ﬂash intensity)/

Hbutton ................................. P. 25, 26

bMENU/b(key locking)/Gbutton

...................................................... P. 27

c Fbutton

dCh (communication channel)/

Ibutton ....................................... P. 24

Display (control panel)Display (control panel)

421 3

MODE

0.0

1/8

TTL

FPRATIO CH

Off

1/8

1/4

1/2

1MODE (ﬂash control mode)

2+/- (ﬂash compensation)/

RATIO (ﬂash intensity)

3FP (Super FP) ﬂash

4CH (communication channel)

5RATIO (ﬂash intensity)

6Group A setting

7Group B setting

8Group C setting

9 d(key lock mode)

Preparing the Commander

Inserting the batteries (sold separately)Inserting the batteries (sold separately)

Batteries to use

Choose from the following batteries.

• AAA NiMH batteries (x 2)

• AAA alkaline dry-cell batteries (x 2)

xAAA manganese batteries are not usable.

Inserting the batteries

1Open the battery compartment cover.

2Insert the batteries.

• Make sure that the polarity (+/-) is correct.

3Close the battery compartment cover.

Attaching the commander to the cameraAttaching the commander to the camera

xMake sure that both the commander and the camera are turned off.

xDirt or moisture on the electrical contacts may cause a malfunction. Wipe off any

dirt or moisture before you attach the commander to the camera.

1Hold down the latch release button (1),

and slide the latch in the direction of the

arrow (2).

Latch

Latch release button

2Insert the commander all the way into the

hot shoe. Hot shoe

Electrical contacts

3Slide the latch in the direction of the

arrow.

Removing the commander

Perform Step 1 of the above procedure and remove the commander from the hot

shoe.

Turning on the Power

ON/OFF button

1Press the ON/OFF button.

xIf the qmark appears in the center of the control panel, the batteries are running

very low. Replace the batteries as soon as possible.

Turning off the powerTurning off the power

Press the ON/OFF button.

Sleep mode/Automatic power offSleep mode/Automatic power off

• With some cameras, the commander will automatically enter the sleep mode

when the camera enters the sleep mode.

• If approximately 60 minutes elapse with no operations, the power will turn off

automatically. Press the ON/OFF button when you want to use the commander

again.

Radio Wireless Shooting

You can use this wireless commander to control multiple receivers through radio

communications. This function only works with Olympus products that support the

radio wireless function.

Refer to the Olympus website for information on products that support the radio

wireless function.

Group controlGroup control

You can control up to three groups of receivers. Within each group, the ﬂashes

will ﬁre with the same settings. This function allows you to shoot with a variety of

lighting effects.

Wireless commander

Flash

(sold separately)

Wireless receiver

(sold separately) Flash with radio

wireless function

(sold separately)

Flash with

radio wireless

function

(sold separately)

Group B

Group A

Group C

Flash with

radio wireless

function

(sold separately)

Communication distanceCommunication distance

The maximum distance for radio wireless communications with this wireless

commander is approx. 30 meters (98.4 ft.) (under Olympus measurement

conditions).

• This distance assumes that there are no obstacles, shielding materials, or

radio interference from other devices.

• The communication distance may be shorter depending on the positions of the

devices, the surrounding environment, weather conditions, and other factors.

FrequencyFrequency

This product uses the 2.4 GHz band for wireless communications. However,

other wireless devices may use the same frequency.

Setup

OK button

Dial

Ch button

MODE button

TEST button

Group button

1Set a ﬂash mode on the camera.

• Refer to the camera manual for details.

2Press the group button to select a communication group.

3Select a ﬂash control mode and adjust the settings.

• For details, refer to the explanations of the ﬂash control modes (P. 25 to

26).

xIf you do not want to use this communication group, select “Off.”

4Press the Ch button to highlight CH. Then, turn the dial to select a

communication channel. Press the OK button to conﬁrm.

• You can select SCAN* or a channel from 1 to 15.

*Select this setting when the communication conditions are poor due to interference from

other devices. When an unused channel appears automatically, press the OK button

again to conﬁrm.

5Match the receiver channel to the commander channel.

6Set the group on the receiver.

7Press the TEST button to check the ﬂash.

Shooting with Automatic Flash Control

(TTL Mode)

The TTL mode adjusts the ﬂash level according to the brightness through the

camera lens. You can use this mode with cameras that support the Olympus TTL

mode. Refer to the Olympus website for a list of compatible cameras.

1Press the MODE button. Then, turn the dial to

select TTL. Press the OK button to conﬁrm.

MODE

FP CH

0.0 1

RATIO

0.0

1/128

TTL

Off

2Set the ﬂash compensation (+/-).

Press the abutton to highlight +/- RATIO. Then, turn the dial to adjust the

setting.

• You can set a ﬂash compensation from -5 to +5.

Press the OK button.

Manually Setting the Flash Intensity

(M Mode)

The ﬂash will ﬁre at the selected intensity. You can use this mode with cameras

that do not support the Olympus communication feature.

1Press the MODE button. Then, turn the dial to

select M. Press the OK button to conﬁrm.

MODE

FP CH

0.0 1

RATIO

0.0

1/100

TTL

Off

2Set the ﬂash intensity (RATIO).

Press the abutton to highlight RATIO. Then, turn

the dial to adjust the setting.

• You can set a ﬂash ratio from 1/1 to 1/128.*1

*1 You can select 1/2 EV or 1/3 EV for the adjustment

increment. (P. 28)

*2 On the scale display, tis the current selection. uis the

previous setting.

Press the OK button.

MODE

ZOOM LED

0.0

RATIO

0.0

1/100

TTL

M1/32

1/64

1/128

Scale display*2

Firing the Flash at a High Shutter Speed

(FP TTL Mode / FP M Mode)

You can shoot with the ﬂash at shutter speeds faster than the ﬂash sync

speed. These modes are useful when you want to shoot a portrait with a blurry

background by widening the aperture, or when you want to use a high shutter

speed to reduce blown-out highlights in the background.

The guide number is lower than in the regular TTL mode or M mode.

1Press the MODE button. Then, turn the dial to select TTL or M. Press

the OK button to conﬁrm.

2Press HIF on the arrow pad to highlight FP.

Then, turn the dial to select “On.”

MODE

FP CH

0.0 1

RATIO

0.0

1/128

TTL

3Adjust the settings.

Setting the ﬂash compensation (+/-) in the FP TTL mode

Press the abutton to highlight +/- RATIO. Then, turn the dial to adjust the

setting.

• You can set a ﬂash compensation from -5 to +5.

Press the OK button.

Setting the ﬂash intensity (RATIO) in the FP M mode

Press the abutton to highlight +/- RATIO. Then,

turn the dial to adjust the setting.

• You can set a ﬂash ratio from 1/1 to 1/128.*1

*1 You can select 1/2 EV or 1/3 EV for the adjustment

increment. (P. 28)

*2 On the scale display, tis the current selection. uis the

previous setting.

Press the OK button.

MODE

ZOOM LED

0.0

RATIO

0.0

1/100

TTL

FP 1/32

1/64

1/128

Scale display*2

Table of contents

Other Olympus Camera Accessories manuals

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Starlite

Starlite OctoDome nxt instructions

Custom Brackets

Custom Brackets Digital PRO-M Instructions for use