OHAUS EXPLORER User manual
Explorer®Balance
Display Tower Mount Kit
Installation Instructions
Explorer®Display Tower Mount Kit 1
1. INTRODUCTION
Please read this manual completely before installation and operation.
CAUTION:
READ ALL SAFETY WARNINGS BEFORE INSTALLING,
MAKING CONNECTIONS, OR SERVICING. FAILURE TO
COMPLY WITH THESE WARNINGS COULD RESULT IN
PERSONAL INJURY AND/OR PROPERTY DAMAGE.
RETAIN ALL INSTRUCTIONS FOR FUTURE REFERENCE.
1.1 Kit Contents
Five M5 Screws
Hex Wrench
Tower with Top
and Foot
2. INSTALLATION
2.1 Safety Precautions
For safe and dependable operation of this equipment, please comply with
all safety precautions mentioned in this manual.
Disconnect equipment from mains power supply before installation.
2 Explorer®Display Tower Mount Kit
2.2 Installation procedure
Follow the steps below. Refer to the Figures when performing these steps.
1
Make sure Balance is unplugged
(turned OFF).
2
Detach the Display:
press buttons on both sides to
disconnect. Then pull Display
away from base.
3
Open the Display:
press buttons (enlarged in photo),
on both sides, then lift Display until
it opens.
4
Open the Display to
access and release the
Display Communication Cable.
Explorer®Display Tower Mount Kit 3
5
Release the clip that secures the
Display Communication Cable:
press out on both sides, as shown.
Unplug the Display Communication
Cable.
6
Un-spool the Display Communication
Cable from the base.
7
Attach Tower to the Base using the
four M5 screws and wrench
(supplied).
Secure the cable as shown:
1. First, under the cable guide,
2. Then under the groove in the
tower base.
Insert the cable plug in the tower
base and feed it through the tower.
Tower mount
M5 screws
Tower mount
M5 screws
4 Explorer®Display Tower Mount Kit
8
Pull the Display Communication
Cable through the top of the tower.
9
Position the Display above the
Tower Platform.
Insert the posts in the receptacles in
the Display Base.
Slide the Display forward as shown,
to seat it in the Tower platform.
10
Insert one M5 screw in the Display
Base to secure it to the Tower
Platform.
Use the supplied Hex Wrench to
tighten the screw.
Explorer®Display Tower Mount Kit 5
11
Insert the cable plug with the security
clip open, then press the security clip
into position to secure the cable.
Route the cable through a groove in
either side of the Display,
or from the rear of the Display,
as preferred.
Pull excess cable down into the Tower
for safety. (Best practice: remove slack
and re-wrap cable around cable
guides on the bottom of the balance.)
12
Re-connect power to the Base.
Use the Level Assist feature to re-level
the Balance. (Keep the Tower foot
raised during this procedure.)
After leveling the Balance, adjust the
Tower foot so it supports the Tower
and is level with the feet of the Base.
13
To adjust the Display viewing angle:
•Press in the two Display Adjust
buttons and move the Display.
Or…
•Loosen the knob that secures the
Tower top and move it.
Ohaus Corporation
7 Campus Drive
Suite 310
Parsippany, NJ 07054, USA
Tel: (973) 377-9000
Fax: (973) 593-0359
With offices worldwide
www.ohaus.com
*83021181*
P/N 83021181 © 2011 Ohaus Corporation, all rights reserved.
Printed in China
Other manuals for EXPLORER
5
Table of contents
Other OHAUS Scale manuals
OHAUS
OHAUS CS Series User manual
OHAUS
OHAUS 4000W Series User manual
OHAUS
OHAUS Emerald User manual
OHAUS
OHAUS Scout STX User manual
OHAUS
OHAUS Scout SJX Series User manual
OHAUS
OHAUS Navigator Balance User manual
OHAUS
OHAUS Pioneer PX Series User manual
OHAUS
OHAUS PAJ-N Series User manual
OHAUS
OHAUS Harvard Trip 1450-SD User manual
OHAUS
OHAUS CS 2000 User manual
OHAUS
OHAUS RA Series User manual
OHAUS
OHAUS 1600 Series User manual
OHAUS
OHAUS SJX1502N/E Operating manual
OHAUS
OHAUS BW Series User manual
OHAUS
OHAUS SJX323 User manual
OHAUS
OHAUS EB3 User manual
OHAUS
OHAUS CS200P User manual
OHAUS
OHAUS Ranger RP Compact Scales User manual
OHAUS
OHAUS Ranger 7000 R71MHD3 User manual
OHAUS
OHAUS AP110 User manual
