OHAUS Catapult 1000 User manual
Quick Start Guide Catapult 1000
Ohaus Corporation www.ohaus.com iCatapult 1000 Scales Quick Start Guide
PREPARATION FOR USE
Check Power
If using AC power, be sure local line voltage
matches voltage printed on the scale’s power
adapter. If not, do not use AC power.
Connect adapter plug to input jack at rear.
To use battery power, remove battery cover
and insert three LR14 (“C”) batteries.
Allow at least five minutes warm-up time,
for scale to stabilize before operation.
SELECTING THE LOCATION:
Place on a firm, steady surface with sufficient space.
Avoid excessive air current, vibrations, heat sources, or rapid temperature changes.
SAFETY PRECAUTIONS
For dependable operation of this product, observe the following precautions:
•Verify that the input voltage printed on the power Adapter and the plug type
matches the local power supply (if using AC power).
•Make sure that the power cord does not pose an obstacle or tripping hazard.
•Disconnect the product from the power supply when cleaning.
•Do not operate this product in hazardous or unstable environments.
•Do not drop loads on the pan.
•Use only approved accessories and peripherals, as available.
•Operate the product only under ambient conditions specified in the Instruction
Manual.
•Service should be performed by authorized personnel only.
Power Input Jack
Catapult 1000 Quick Start Guide
Catapult 1000 Scales Quick Start Guide ii Ohaus Corporation www.ohaus.com
CONTROLS
Button Functions
UNITS
Cal
Short Press
Long Press
Changes weighing unit and weighing mode.
In Dynamic Weighing Mode, starts countdown.
Starts calibration.
ON/ZERO
Off
Short Press (when off)
Short Press:(when on)
Long Press
Turns scale on.
Sets display to zero.
Turns scale off.
OPERATION
Power On: Press
All display segments appear, then the software version.
Display resets to zero.
To Zero: Press
when scale is on, display returns to zero.
To Tare: Press
with container on scale. Add mass to see NET weight.
If both sample and container are removed, display shows a negative value.
Overload: If load exceeds scale capacity, “E” appears. Remove load, scale returns to normal.
Auto Shut-Off: When running on batteries, scale turns off after four inactive minutes.
Dynamic Weighing
With platform empty, press
repeatedly until bullet • flashes.
Place a mass on the platform. The scale shows “-A-”.
(If using a container, press ZERO to tare.)
P
ress
to start the averaging countdown from 5 seconds.
Averaged weight appears. Bullet • stops flashing when process is complete.
Display holds until a button is pressed.
To Exit, remove mass from platform. Press
until kg or lb appears on display.
*80253136*
P/N 80253136
Stability
symbol
Battery charge
symbol
Symbols for weighing modes:
lb – Pounds
•
– Dynamic Weighing
kg – Kilograms
Negative
symbol
Other manuals for Catapult 1000
6
Table of contents
Other OHAUS Scale manuals
OHAUS
OHAUS Compass CX Series User manual
OHAUS
OHAUS Navigator NVT1601M User manual
OHAUS
OHAUS Valor 3000 User manual
OHAUS
OHAUS CKW Series User manual
OHAUS
OHAUS BW1.5 User manual
OHAUS
OHAUS RU-U2 User manual
OHAUS
OHAUS PS121 User manual
OHAUS
OHAUS I-C52M100L User manual
OHAUS
OHAUS PS Series User manual
OHAUS
OHAUS Emerald User manual
OHAUS
OHAUS Courier 3000 User manual
OHAUS
OHAUS YJ103 User manual
OHAUS
OHAUS Navigator Use and care manual
OHAUS
OHAUS ES30R User manual
OHAUS
OHAUS SJX1502N/E Operating manual
OHAUS
OHAUS PR Series User manual
OHAUS
OHAUS Emerald User manual
OHAUS
OHAUS ranger 7000 User manual
OHAUS
OHAUS MB90/MB120 User manual
OHAUS
OHAUS Guardian 2000 User manual
