OEM 24801 Service manual

Please read and save these instructions. Read through this owner’s manual carefully before using product.

Protect yourself and others by observing all safety information, warnings, and cautions. Failure to comply with

instructions could result in personal injury and/or damage to product or property. Please retain instructions for

future reference.

20 GALLON (75L) PARTS WASHER

Unpacking

After unpacking unit, inspect carefully for any damage

that may have occurred during transit. Check for loose,

missing, or damaged parts. Shipping damage claim

must be ﬁled with carrier.

Speciﬁcations and Dimensions

Maximum Capacity Working Capacity Assembled Dims (Inches)(CM) Weight

Model Gallons Gallons Length Width Height (Lbs) (Kgs)

24801 20 (75L) 12 (45L) 31” x 21”x 34 1/2” (78.7 x 53.3 x 87.7cm) 52 23.6

Operating Instructions and Parts Manual 24801

SAFETY RULES

1. Know your tool. Read this manual carefully. Learn

the tool’s applications and limitations, as well as,

potential hazards speciﬁc to it.

2. Ground all tools. If the tool is equipped with three-

pin plug, it should be plugged into a three-pin

electrical socket. Never remove the ground pin.

Failure to properly ground unit could result in severe

electrical shock and / or death.

3. Do not abuse cord. Never use the cord to carry tools

or pull the plug from an outlet. Keep cord away from

heat, sharp edges or moving parts. Replace dam-

aged cords immediately. Damaged cords increase

the risk of electric shock.

4. Keep work area clean and well lit. Cluttered or dark

work areas invite accidents.

5. Keep children away. All children should be kept

away from the work area. Never let a child handle a

tool without strict adult supervision.

6. Do not operate this tool if under the inﬂuence of

alcohol or drugs. Read warning labels on prescrip-

tions to determine if your judgment or reﬂexes are

impaired while taking drugs. If there is any doubt, do

not attempt to operate.

7. Use safety equipment. Eye protection should be

worn at all times when operating this tool. Use ANSI

approved safety glasses. Everyday eyeglasses are

NOT safety glasses. Dust mask, non-skid safety

shoes, hard hat, or hearing protection should be

used in appropriate conditions.

3/13

2013 ©OEM-TOOLS

Operating Instructions and Parts Manual 24801

20 GALLON (75L) PARTS WASHER

8. Wear proper apparel. Loose clothing, gloves, neck-

ties, rings, bracelets, or other jewelry may present a

potential hazard when operating this tool. Keep all

apparel clear of the tool.

9. Don’t overreach. Keep proper footing and balance

at all times when operating this tool.

10. Always disconnect the tool from power source

before making any adjustments, storing, servicing,

or changing accessories. Such preventative safety

measures reduce the risk of starting the tool ac-

cidentally.

11. Do not use the tool if the switch does not turn it on

and off. Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

12. Check for damage. Check your tool regularly. If

part of the tool is damaged it should be carefully

inspected to make sure that it can perform its

intended function correctly. If in doubt, the part

should be repaired. Refer all servicing to a qualiﬁed

technician. Consult your dealer for advice.

13. Keep away from ﬂammables. Do not attempt

to operate this tool near ﬂammable materials or

combustibles. Failure to comply may cause serious

injury or death.

14. Store idle tools out of the reach of children and

untrained persons. Tools may be dangerous in the

hands of untrained users.

GETTING STARTED

Unpack your OEM 20 Gallon (75L) Parts Washer. After

unpacking the unit, inspect carefully for any damage

that may have occurred during transit. Check for any

loose, missing or damaged parts.

YOUR OEM PARTS WASHER INCLUDES:

Bolts . . . . . . . . . . . . . . . . . . . . . . . .24

Spring Washers . . . . . . . . . . . . . . . .24

Lock Nuts . . . . . . . . . . . . . . . . . . . . 24

Legs . . . . . . . . . . . . . . . . . . . . . . . . 4

Lower Shelf . . . . . . . . . . . . . . . . . . .1

Middle Shelf . . . . . . . . . . . . . . . . . . .1

Pump Assembly . . . . . . . . . . . . . . . 1

Basket . . . . . . . . . . . . . . . . . . . . . . .1

POWER SOURCE CONNECTION

POWER REQUIREMENTS

This product is designed to operate on a properly

grounded 120 volt, 60Hz, single-phase alternating

current (AC) power source fused with a 20 amp time

delayed fuse or circuit breaker. It is recommended that

a qualiﬁed electrician verify the ACTUAL VOLTAGE at

the receptacle into which the product will be plugged

and conﬁrm that the receptacle is properly fused and

grounded.

DO NOT OPERATE THIS PRODUCT if the ACTUAL

power source voltage is less than 105 volts AC or

greater than 132 volts AC. Contact a qualiﬁed electri-

cian if this problem exists. Improper performance and/

or damage to the product will result if operated on

inadequate or excessive power.

CONNECT TO POWER SOURCE

Consult a qualiﬁed electrician for proper installation of

receptacle at the power source.

This product must be grounded while in use to protect

the operator from electrical shock. If you are not sure

if your outlet is properly grounded, have it checked

by a qualiﬁed electrician. Do not cut off the ground-

ing prong or alter the plug in any way and do not use

any adapters between the product’s power cord and

the power source receptacle. Make sure the POWER

switch is OFF then connect the power cord to a

properly grounded 120V, 60Hz, single phase, 20 amp

power source.

EXTENSION CORDS

For optimum performance, an extension cord should not

be used unless absolutely necessary. If necessary, care

must be taken in selecting an extension cord appropri-

ate for use with your speciﬁc product. Select a properly

grounded extension cord that will mate directly with the

power source receptacle and the power cord without

the use of adapters. Make certain that the extension is

properly wired and in good electrical condition. Extension

cords must be a minimum # 12 gauge cord. Do not use

an extension cord over 25 ft. (7.6m) in length.

WHEN INSTALLING YOUR PARTS WASHER

1. Assemble it according to the instructions given below.

2. Sit it on a ﬁrm, ﬂat, level surface in a well ventilated

area and away from any open ﬂames.

3. Fill only with a non-ﬂammable water-based degreas-

er or cleaning agent, such as Simple Green to just

below the level of the parts shelf (approximately 24

gallons or 90L).

4. Follow the degreaser manufacturer’s instructions carefully.

5. Do not ﬁll with ﬂammable solvents such as kero-

sene, gasoline, etc.

WARNING

High voltage danger from power source!

Operating Instructions and Parts Manual 24801

20 GALLON (75L) PARTS WASHER

WHEN USING YOUR PARTS WASHER

1. Wear suitable protective clothing, gloves and goggles.

2. Clean off any accidental splashes of degreaser on

skin immediately, following the degreaser manufac-

turer’s instructions carefully. Seek medical attention

if necessary.

3. Keep work area tidy and mop up any accidental

spills of degreaser.

WHEN NOT IN USE

1. Switch off pump, close the lid and disconnect from

the electrical supply.

2. Disconnect from the electrical supply before carrying

out any maintenance or cleaning on the parts washer.

The pump of your parts washer may

be damaged if you use solvents like perchloroethy-

lene or trichloroethylene.

ELECTRICAL CONNECTIONS

Plug into a standard 120 volt grounded plug.

This appliance must be grounded.

ASSEMBLY INSTRUCTIONS

1. Remove machine from carton and inspect for any

visual damage.

2. Remove parts inside the machine.

3. Lay clean and hard cardboard on the ﬂoor and lay

machine on its lid. (Make sure you hold cover closed

when laying machine on its lid.)

4. Mount four legs on brackets with M6X12 Philips head

screws and M6 nuts. NOTE: DO NOTTIGHTEN.

5. Place lower shelf between legs with ﬂat surface up

and attach to legs with M6X12 philips head screws

and M6 nuts.

6. With legs pressed tight against lower shelf, tighten

all screws to lower shelf.

7. Tighten all the screws installed in Step 4.

8. Stand machine up, being careful to hold lid closed.

9. Put work shelf and basket into the machine.

10. Remove Styrofoam packing from pump (see pump

label for instructions) and mount pump assembly into

slot on the side of the machine. Push down ﬁrmly

on pump so that it seats itself onto side wall of tub.

Place ﬁlter screen in position.

11. Thread the ﬂexible nozzle into the elbow attachment

on pump housing and ﬁrmly screw into place.

12. Plug machine into standard 115 volt 60 Hz ground-

ed outlet and ﬁll with proper amount of ﬂuid.

13. Turn switch on. Fluid should be ﬂowing from the

ﬂexible nozzle.

OPERATION

Always wear protective clothing, gloves and goggles

when using your Parts Washer.

1. Open the parts washer lid and place parts to be

washed on the washboard.

2. Position the ﬂexible nozzle so that it is directly

above your parts.

3. Turn the power switch to the ON position.

4. Clean parts as needed.

5. Turn power switch to the OFF position.

6. Place parts on drying shelf until completely dry.

7. Empty drain tank, as needed, by sliding out of

drying shelf brackets.

MAINTENANCE

1. The lid incorporates a fusible link to close the lid

in the event of a ﬁre. This link is non-resetting and

must be replaced once it has been triggered.

2. Clean the pump ﬁlter regularly by sliding it away from

the pump housing and rinsing in clean degreaser.

3. Do not allow the level of liquid in the parts washer to fall

below the pump inlet, as damage to the pump can result.

4. Change degreaser as needed. Tank can be drained by

removing the drain plug located on bottom of tank.

TROUBLE SHOOTING

The only trouble you should ever experience with your Parts

Washer is reduced volume ﬂow or no ﬂow of cleaning liquid

from the ﬂex hose nozzle. The probable cause is:

1. Foreign matter in the ﬂex hose.

2. Low ﬂuid level (not reaching the pump inlet).

3. Blocked/dirty ﬁlter.

4. Air in the pump. You can turn on and turn off the

parts washer for several times or knock on the

pump housing for several times to ﬁx this problem.

LIMITED 90 DAY WARRANTY

This warranty excludes inciden-tal/consequential damages and

failures due to misuse, abuse or normal wear and tear. This

warranty gives you specific legal rights, and you may also have

other rights, which vary, from state to state. OEM will not be

responsible for any consequen-tial or incidental damages

arising from the breach of this or any other warranty, whether

expressed, implied or statutory. Some states do not allow the

exclusion or limitation of consequential or incidental damages,

so the above exclusion may not apply to you. This warranty

gives you specific legal rights, and you may also have other

rights which vary from state to state.

ALWAYS WEAR SAFETY GOGGLES.

WARNING

Clean off any accidental splashes of degreaser

on skin immediately, following the degreaser

manufacturer’s instructions carefully.

Seek medical attention if necessary.

Operating Instructions and Parts Manual 24801

20 GALLON (75L) PARTS WASHER

PARTS LIST AND DIAGRAM

Reference No. Description ......................Qty

1 24801-01 Cover .............................4

2 24801-02 Fusible Link .........................1

3 24801-03 Shaft...............................1

4 24801-04 Work Basket ........................1

5 24801-05 Work Shelf ..........................1

6 24801-06 Body ..............................1

7 24801-07 O-ring..............................1

8 24801-08 Plug ..............................1

9 24801-09 M6 Nut ............................24

10 24801-10 Spring Washer .....................24

11 24801-11 M6 x 12 Screw......................24

12 24801-12 Leg ................................4

13 24801-13 Shelf ..............................1

14 24801-14 Filter Cover .........................1

15 24801-15 Filter ..............................1

16 24801-16 Pump Housing Cover .................1

17 24801-17 M5 x 20 Screw ......................1

Reference No. Description ......................Qty

18 24801-18 M5 Nut ............................1

19 24801-19 Pump Housing ......................1

20 24801-20 Flexible Pipe. . . . . . . . . . . . . . . . . . . . . . . . .1

21 24801-21 Elbow Seat..........................1

22 24801-22 Strain Relief .........................1

23 24801-23 M4x8 Screw w/Nut, Spring & Flat Washer .......5

24 24801-24 Switch .............................1

25 24801-25 Switch Box .........................1

26 24801-26 Elbow-1 ............................1

27 24801-27 Elbow-2 ............................1

28 24801-28 O-ring .............................1

29 24801-29 Connector ..........................1

30 24801-30 O-ring..............................1

31 24800-12 Pump ..............................1

32 24801-32 Strain Relief .........................1

33 24801-33 Cable & Plug ........................1

34 24801-34 Pump Assembly......................1

2930 28

Other OEM Washer manuals

OEM

OEM 24800 Service manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide