Oasis PCPEBQ User manual

FREE STANDING ONTACTLESS BOTTLE

FILLER WITH QUASAR UVC-LED

Installation Instructions For

UNIFILTERED

PCPEBQ

PCPEBQY (230V)

PCP10EBQ

PCP10EBQY (230V)

FILTERED

PF2CPEBQ

PF2CP10EBQ

OASIS International

222 East Campus View Blvd.

Columbus, OH 43235

614-861-1350

www.oasiscoolers.com

INDEX

INDEXINDEX

INDEX

1. PRODUCT SPECIFICATIONS

2. IMPORTANT REQUIREMENTS

3. SAFETY WARNINGS

4. GETTING STARTED

5. PROPER QUICK CONNECT FITTING CONNECTION INSTRUCTIONS

6. INSTALLATION

7. QUASAR UVC-LED OPERATION

8. SET-UP GUIDE FOR DISPENSER PCB ELECTRONICS

1. PRODUCT SPECIFICATIONS

1. PRODUCT SPECIFICATIONS1. PRODUCT SPECIFICATIONS

1. PRODUCT SPECIFICATIONS

Dimensions:

Depth 13.35”(339.0 mm)

Width 12” (304.8 mm)

Height 49.7” (1262.4 mm)

Refrigerant: R-134a

Input Voltage: 115 VAC, 60 HZ or 220/240 VAC, 50/60HZ –See Data

Plate

ROUGHING-IN AND DIMENSIONAL DRA ING

•Use only original and new parts to guarantee the reliability, optimization, and

performance of the OASIS water machine.

•Always wear proper protection when performing any type of service or

maintenance.

•When cleaning the unit, do not use corrosive acidic products, or metal

brushes.

•Do not wash the unit using high-pressure water.

•Connect to a water supply with a pressure of 45 PSI minimum to 100 PSI

maximum (3.10 bar minimum to 6.89 bar maximum ).

•ARNING: DO NOT USE WITH WATER THAT IS MICROBIOLOGICALLY UNSAFE

OR OF UNKNOWN QUALITY.

•ATTENTION: IT IS IMPORTANT TO MAKE PROPER CONNECTIONS TO THE

QUICK CONNECT FITTINGS TO AVOID LEAKS. SEE SECTION 5.

•CAUTION: DO NOT PLACE UNDUE STRESS OR SIDE LOAD ON ANY OF THE

PLASTIC FITTINGS.

•CAUTION: DO NOT ACTIVATE SENSOR WITHOUT WATER.

2. IMPORTANT REQUIREMENTS

2. IMPORTANT REQUIREMENTS2. IMPORTANT REQUIREMENTS

2. IMPORTANT REQUIREMENTS

BEFORE YOU START USING THIS ATER DISPENSER, PLEASE READ THE

FOLLO ING INSTRUCTIONS CAREFULLY.

•The unit must be connected to a 115 VAC GFCI or 230VAC power supply as

listed on the equipment data label.

•The unit must be protected by a properly installed 20 amp circuit breaker.

Verify that the electrical current is correct for the power of this unit, which is

listed on the machine data label.

•To avoid electrical shock always unplug the unit from the electrical outlet

before servicing.

•If the power supply cord is damaged, it must be replaced by a special cord or

assembly available from the manufacturer or its service agent.

•This appliance must be earthed.

•Children should be supervised to ensure that they do not play with this

appliance.

3. SAFETY WARNINGS:

3. SAFETY WARNINGS:3. SAFETY WARNINGS:

3. SAFETY WARNINGS:

4. GETTING STARTED:

4. GETTING STARTED:4. GETTING STARTED:

4. GETTING STARTED:

What’s Included

a. CONTACTLESS BOTTLE FILLER

b. STABILIZER BRACKET

c. OPTIONAL VERSAFILTER III

d. OPTIONAL REMEDI FILTER

VERSAFILTER III

(filtered models

only)

CONTACTLESS

BOTTLE FILLER

STABILIZER BRACKET

Remedi filter element

(filtered models only)

NOTE This comes

installed in the cooler.

Quick-Connect Fittings

•If you need to cut the plastic tubing, be sure to cut tube ends square

and straight. Do not deform the tube (i.e., cause tube to compress its

diameter so it is no longer round, or it may result in a water leak at the

fitting).

•Make sure the outer surface of the tube is clear of marks or scratches

for a length equal to twice the tube diameter. This allows the “O” ring

to seat properly against the tube (See figure below).

•Avoid sharp changes in direction when routing the tubing. Sharp turns

could cause the tubing to kink, which reduces its flow capacity and or

stops it completely.

•Fittings consist of two parts a body and a collet. (See figure below).

•To install a tube, push it through the collet until it seats firmly at the

bottom of the fitting.

•To remove a tube, push and hold the collet against the body while

pulling the tube out. Pushing the tube into the body before pushing the

collet in will aid in the removal of the tube.

5. PROPER QUICK CONNECT FITTING CONNECTION

5. PROPER QUICK CONNECT FITTING CONNECTION 5. PROPER QUICK CONNECT FITTING CONNECTION

5. PROPER QUICK CONNECT FITTING CONNECTION

INSTRUCTIONS:

INSTRUCTIONS:INSTRUCTIONS:

INSTRUCTIONS:

Push tube through

Collet into Body

Tube must seat firmly

At bottom of fitting

Push Collet against

Body to release tube

STEP 1 & 2:

1. Carefully unpack Water Dispenser and remove filter

from the alcove. (filtered models only)

2. Remove Front Panel by removing the 2 screws at the

bottom of the panel on the sides. See Diagram 2.

6. INSTALLATION:

6. INSTALLATION:6. INSTALLATION:

6. INSTALLATION:

DIAGRAM 1 DIAGRAM 2

REMOVE

T15 TORX SCREWS

QTY. 2

Filtered

Model

Shown

STEPS 3 through 5 (for optional filters)

Note If this unit is equipped with a two stage filtration system, then the remedi

filter was shipped installed. The VersaFilter III was placed in the alcove on the

front of the cooler for shipping.

3. Unpack the VersaFilter III and remove the sanitary cap.

4. Looking at the filter top, orient the filter so that the rectangular lug, on top

of the filter faces forward.

5. Push the filter up into the filter housing and rotate the filter one-quarter

turn to the right until it stops turning. Refer to Diagram 3

6. INSTALLATION:

6. INSTALLATION:6. INSTALLATION:

6. INSTALLATION:

DIAGRAM 3

Remedi Filter –

shown in Green

Filter housing was

installed at the

factory.

VERSAFILTER III

Lug IMPORTANT: When

replacing filter

cartridge, turn OFF

water supply.

Depressurize water

lines prior to removal

of filter housing from

the quarter turn

filter head assembly.

STEP 6:

6. Locate the snap bushing in the back of the cabinet and feed 1-1/2” OD Drain

Pipe through the hole. See Diagram 4 & 5.

6. INSTALLATION:

6. INSTALLATION:6. INSTALLATION:

6. INSTALLATION:

DIAGRAM 4

Front View

DIAGRAM 5

Rear View

P-Trap Located

behind the

filter mounting

bracket

Drain Pipe –

shown after

completing

Step 6.

6. INSTALLATION:

6. INSTALLATION:6. INSTALLATION:

6. INSTALLATION:

CONNECT WATER SUPPLY

Rear View

STEPS 7 through 9:

(See Diagram 6)

7. Connecting 1/4” OD water supply tube to 1/4” quick connect fitting on the

back of the unit. Refer to Section 5 for instructions on how to properly

connect to quick connect fittings. IMPORTANT: Before connecting water

supply to dispenser, flush building water supply.

8. Connect 1-1/2” OD drain pipe to Elbow Coupling (not provided). Connect to

building drain.

7. Attach stabilizing bracket to the unit with screws provided. Then secure the

bracket to the wall with wall anchors provided by others.

CONNECT DRAIN

Diagram 6

ATTACH STABILIZER BRACKET

Other manuals for PCPEBQ

This manual suits for next models

Table of contents

Other Oasis Water Dispenser manuals

Oasis

Oasis B1RR User manual

Oasis

Oasis BAEB1SHSK User manual

Oasis

Oasis Kalix Series Service manual

Oasis

Oasis BPA1SK Technical manual

Oasis

Oasis MAXXFILL PULSE User manual

Oasis

Oasis PCPEBF User manual

Oasis

Oasis PM User manual

Oasis

Oasis B1RRK Manual

Oasis

Oasis POU Instruction sheet

Oasis

Oasis P1PVCDKY Installation and maintenance instructions

Oasis

Oasis P1PV Series Installation and maintenance instructions

Oasis

Oasis P8FPM User manual

Oasis

Oasis Quasar PWEBQ User manual

Oasis

Oasis 032725-005 Installation and maintenance instructions

Oasis

Oasis 115V POU1CCT User manual

Oasis

Oasis VERSACOOLERII PAC User manual

Oasis

Oasis VERSAFILLER P EBF Series User manual

Oasis

Oasis MAXXFILL FLEX User manual

Oasis

Oasis PSWSA1SK User manual

Oasis

Oasis MIR311D-3 User manual

Oasis

Oasis PCPD10EBQ User manual

Oasis

Oasis POU1AQ Series User manual

Oasis

Oasis POU_1RREC Series Installation and maintenance instructions

Oasis

Oasis 506336C User manual

Popular Water Dispenser manuals by other brands

Monarch Water

Monarch Water ULTIMATE MINI AQUA HE install guide

Haier

Haier HLM-109B instruction manual

abc

abc Fleck 5600SXT manual

GE GXOF18G Owner's manual and installation instructions

Kenmore

Kenmore 625.385560 UltraFilter 650 owner's manual

Innova

Innova CEV+ Installation, use and maintenance

Aries

Aries Hydra DI Operation & maintenance manual

GE GNCF02H owner's manual

ProFlo

ProFlo PFB Series Installation & operation manual

Hydrotech

Hydrotech 89DF HIM owner's manual

A.O. Smith

A.O. Smith FREZYA 300S user manual

Frakco

Frakco Travelsoft RV 2400HD Operation instructions

GE GXSF30V Owner's manual and installation instructions

Avanti

Avanti WD31EC instruction manual

Avanti

Avanti WD360 instruction manual

BRIO

BRIO CLCTTL520 Setup manual

3M HCD-1 operating instructions

Elkay

Elkay EFHFA8_2CJO Installation, care & use manual