Nova Bidet Ultra-NOVA User manual
Owners manual for models:
Ultra-NOVA
Ultra-NOVA+
NOVA
U
l
t
r
a
BIDET
NOVA
®
Parts
Installation
Testing Before Use
Operation
Cleaning
Warranty
Technical Specifications
5-6
7-11
12
13-16
17
20
22
Warnings and Precautions 4
Troubleshooting 19-20
Features 3
Content:
3
Please confirm the model you purchased first, and then check the corresponding function.
The model and specification can be found on the nameplate at the rear of the machine.
Models
Functions
Ultra-NOVA
Ultra-NOVA+
Basic
functions
Seat heating
Water heating
Rear/Female Wash
Warm air drying
Additional
functions
Auto lid open/close
Lid slow close
Moving wash
H/C Massage
Auto flushing
Smart Remote
Control
Energy saving
E-Water
Sterilization
Antibacterial seat
External filter
Enema Wash
Features
4
Warnings and precautions
• Do not kink water hose
• Do not get the unit wet
• Unplug before cleaning
• Only use natural cleaners on unit
• Use with GFCI outlet only
• If extension cord is needed use 14 or 12 gauge
• This unit is only intended for use as described in this manual
• Do not use if the unit is damaged
5
Seat
Seating Sensor
Safety Instructions
Lid
Lid Bumper
Bidet Nozzle
Plug
Drying Air Outlet
Water Supply
Connector
Control Knob
Water Temperature
Button
Seat Temperature Button
Auto Flushing Controller
(Only for Ultra-NOVA+)
Parts
6
6
5
NO.
Bidet Seat Remote Control
Remote Mounting
Bracket & Guide
Expansion Tube
Wall Screw
Auto-Flush Module
Mounting Plate
Locking Bracket
Top Mounting Bolts
T-Connector Rubber O Ring
Rubber Sleeve
Bolt
Supply Hose
Filter
Owners Manual
Cardboard
Installation Guide
3
Name Sketch
1
2
Quantity
1pcs
4
1pcs
2pcs
2pcs
2pcs
1pcs
2pcs
2sets
1pcs
1pcs
1pcs
1pcs
1pcs
NO. Name Sketch
Quantity
7
1pcs
1pcs
1pcs
1pcs
4pcs
These parts are only for Ultra-NOVA+
Small Clamp Collar
Top outer diameter of fittings
from 2½in to 2¾in.
Large clamp collar
Top outer diameter of fittings
from 2¾in to 3⅛in.
Push Rod Extension
(Only use if Push Rod is
too short)
Clamp Screw
Parts list
Parts
Mounting Plate
Dryer
Seat Bumper
Mounting Plate
Release Button
Ownersmanual for models:
Ultra-NOVA
Ultra-NOVA+
NOVA
U
l
t
r
a
BIDET
NOVA
®
.
7
1. Preparation before installation
Size requirements of bidet seat
A
BD
C
Before installing the bidet seat:
A. Remove the existing toilet seat
and turn off the Water Supply
Valve.
B. Flush the toilet and hold down
the flush lever or button for 5 to
10 seconds.
C. Place a sponge, rag, or bucket
under the toilets water inlet.
D. Disconnect toilets Water Supply
Hose from the Toilets Water
Inlet.
Installation
Flush Button
Toilets Water Inlet
Water Supply Valve
Water Supply Hose
A. Distance from water tank to the front of
toilet: 19.9” - 21” (505-535mm).
B. Distance from mounting holes to the back
edge of toilet bowl: >2.75” ( 70mm).
C. Spacing between two mounting holes:
4.6” - 7.2” (118-182mm).
D. Distance from mounting hole to water
tank: >1.2” (30mm).
8
3. Secure Ultra NOVA Seat
2. Install the Mounting Plate
Rubber Sleeve
Mounting Plate
Toilet
Mounting Hole
Mounting Plate Groove Locking Bracket
Bolt
Installation
Mounting Plate
Toilet Tank
Align the bottom of the Seat with the
Mounting plate, and push toward the
Toilet Tank.
When you hear the "click" sound, it
indicates that it is locked in place.
Anti-skid pad
Note: For uneven ceramic, add 2mm thick pad at the rear end of the Mounting Plate.
A. Push the Rubber Sleeve into the
Mounting Hole of the Toilet.
B. Place Mounting Plate over the
Mounting Holes on the Toilet and
align it using the Cardboard
Installation Guide.
C. Place Locking Brackets over
Mounting Holes.
D. Slide Bolts through the Locking
Bracket and into the Rubber
Sleeves.
E. Tighten Bolts.
9
1. Turn off the power and water.
2. Remove the Toilet Tank Cover
Toilet Tank Cover
Installation (Auto-Flush)
1. Place Automatic Flushing Module into the top of the fittings as shown in the figure.
2. Make sure the Push Rod is aligned with the Flush Button. If the Push Rod cannot press the
Flush Button, insert the Adjusting Block into the Push Rod.
3. Tighten the Wing Bolt to till secure then tighten 4 Clamp Screws.
4. Secure the power cord at the screw position with a tie (If there is a groove in the top of the
water tank, pass the wire thought the goove).
5. Turn on the water source, connect the power supply, and test the manual and automatic
flushing functions.
6. Close the water tank cover.
Wing Bolt
Collar Clamp
Flush Button
Automatic
Flushing Module
Cable Ties
3. Measure the outer diameter and height of the
top of the Top Flush Cylinder. The diameter should
be between 2½in and 3⅛in and the height should
be above ¾in otherwise the Automatic Flushing
Module is not usable.
Confirm Top Flush Cylinder diameter before installation
Automatic Flushing Module
Collar Clamp
Collar and Flushing Module connected
Install external automatic flushing unit
(
Installation and fixation of flushing module
Clamp
Screw Push Rod
Only for Ultra NOVA +)
4. Find the appropriate sized collar. The
collar should be able to fit around the flush
cylinder but it’s ends should not be able to
touch each other.
5. Secure the collar to the flushing module by
sliding it sideways with the screw holes on
the collar facing up, as shown below. (You
should hear a click)
2½in and 3⅛in
>¾in
10
4. Connect all water supply parts
5. Connect power
Plug into GFCI wall outlet.
Caution
Outlet must have GFCI (Ground-fault circuit interrupter).
Outlet must be on 15+ AMP dedicated circuit.
Cord is limited to 4 feet by law.
If extension cord is used, it must be 14 gauge or larger.
Ultra-NOVA
Supply Hose
Ultra-NOVA
Water Inlet
T-Connector
Water Filter
Water Supply Shutoff
Toilet Supply Hose
Alternate T can be purchased and used at the water
supply shutoff if underside of toilet is unaccessible.
Installation
A. Screw T-Connector onto toilet.
B. Screw Toilet Supply Hose onto bottom of
T-Connector.
C. Screw Water Filter onto side of T-Connector
D. Screw one side of Ultra-NOVA Supply Hose
onto filter and the other side to Ultra-NOVA
Water Inlet.
E. Turn on Water Supple Shutoff.
F. Check all connections for leaks.
This manual suits for next models
1
Table of contents
