Notifier AFP-400 User manual

Doc. 50392:B 03/06/97 Page 1 of 2

12 Clintonville Road.

Northford, CT 06472

Overview

AFP-300/AFP-400 Cabinets (AA Series)

PRODUCT INSTALLATION DRAWING

Document 50392 Rev B

Part Number 50392-B

ECN 96-463 03/06/97

The cabinet is a backbox and door that can contain a small AFP-300/AFP-400

system. A small system supports up to twelve NACs and consists of the CPU

module and one option module. Modules mount to rails in the cabinet, eliminat-

ing the need for optional chassis assemblies. Mounting methods include surface-

mounting or semi-flush mounting on a wall (with an optional TR-500) between 16-

inch-on-center studs.

CabinetLimitations

UnpackingtheCabinet

Before installing the cabinet, read the following:

 Review the installation precautions listed in the AFP-300/AFP-400 Installation

Manual.

 All wiring must comply with the National and/or Local codes for fire alarm

systems.

 Count the number of conductors needed for all devices and find the appropriate

knockouts.

 Do not draw wiring into the bottom 9 inches of the cabinet, except when using

the BB-17. This prevents interference between the power supply and batteries.

StandardsandCodes In addition, installers should be familiar with the following standards:

 NEC Article 300 Wiring Methods

 NEC Article 760 Fire Protective Signaling Systems

 Applicable Local and State Building Codes

 Requirements of the Local Authority Having Jurisdiction

PreparingforInstallation

Unpack the cabinet as follows:

 Limited power supply capacity (one AVPS-24 expander).

 Backbox can hold 12 amp-hour batteries only.

 Maximum of one module in addition to the CPU-400.

 No voice evacuation capability.

Technical Manuals Online! - http://www.tech-man.com

Page 2 of 2 Doc. 50392:B 03/06/97

Mount a cabinet on a surface in a clean, dry, vibration-free area. To install the

cabinet so the center of the control panel keypad measures 60 inches above the

finished floor, follow these instructions:

1) Locate the cabinet so that the top edge is 66 inches above the surface of the

finished floor.

2) Mount the backbox using the four mounting holes in the back surface of the

backbox.

Dress Panel

Door

!

Caution: Unless you are

familiar with the place-

ment of components

within this backbox, use

only the knockout

locations provided for

conduit entry.

Assembling the Cabinet

Assemble the cabinet as follows.

1) Install the Dress Plate mounting screws.

2) Install control panel components (refer to the AFP-300/AFP-400 Installation

Manual).

3) Install the Dress Panel and tighten the mounting screws.

4) Place the door on the hinge pins.

Mounting the Cabinet

Door hinge

(2 places)

MountingtheCabinet

Dress Panel

mounting screw

AssemblingtheCabinet

Technical Manuals Online! - http://www.tech-man.com

Other manuals for AFP-400

2

This manual suits for next models

1

Popular Smoke Alarm manuals by other brands

x-sense

x-sense SD19-W user manual

BRK electronic

BRK electronic First Alert P1010 quick start guide

FireAngel

FireAngel Thermoptek ST-622 user manual

teko

teko Astra-42A user guide

Safetec

Safetec SDS-2/6 Additional Fault Finding Instructions

Siemens

Siemens PE-11C installation instructions

System Sensor

System Sensor DH500ACDC Installation and maintenance instructions

Resolution Products

Resolution Products RE612 CryptiX quick start guide

First Alert

First Alert PC900V user manual

Eminent

Eminent EM6590 E-Domotica user manual

Ei Electronics

Ei Electronics Ei Ei168RC user manual

Carrier

Carrier Kidde Quell Q301 user manual

VESDA

VESDA VLF-500 Product guide

ELRO

ELRO FS8110 instruction manual

Heiman

Heiman SMOKI NS-626PHS user manual

Regin

Regin SDD-S65 instruction manual

Family Gard

Family Gard FG225 user manual

Greystone

Greystone DSD120 Installation and maintenance instructions