Nortel 3050 User manual

P0881594 Issue 02 MICS-XC Norstar-Companion Installer Guide

Registering individual portables

Registering the C3060

The following section describes the procedures involved in

registeringCompanionC3060 portabletelephones.Toregister

each portable with theNorstar system, you must dotwo things:

• Register the portables by entering the Registration

password on each one.

• Verify that the portable functions correctly.

C3060 Icons

The following table identifies the C3060 portable telephone

icons:

To register the C3060

1. Turn on registration for your system.

2. Press m***. The display shows A

ION

ONON

and three softkeys, SYS,PINFO,DATA.

3. Press S

S. The display shows W

S S

C3060 Icon function

Mute button

kHang up button

iAnswer button

mFeature button

lTelephone directory button

jService directory button

90 / Registering individual portables

MICS-XC Norstar-Companion Installer Guide P0881594 Issue 02

Note: Wireless Systems is a registration list of names for up

to six different systems. If the list is full, and you must

add another system, de-register an existing system

name.

4. Press A

ADD

DDDD

DD to establish a radio link. The display briefly

shows A

g S

: (next system number). If ADD,

not available, start over at step 1 again.

The display shows P

: for an established radio link.

The display shows N

o c

n for a radio link not

established.

Note: If more than 30 minutes have elapsed since the last

registration, enable the system for registration. See

Meridian Companion Administration Terminal

Operations Guide.

5. Enter the registration password. The default password is

72346 (RADIO). The display shows W

The display shows In

InIn

Invld

vldvld

vld P

d for a wrong password.

6. Enter the four-digit Wireless Terminal Number (WTN).

The display shows E

r n

The display shows In

InIn

Invld

vldvld

vld W

Nwhen the WTN is wrong.

The display shows R

g f

dwhen the registration fails.

If you try to register the C3060 to the same system twice,

the display shows the registered name. For example

ed a

d ad a

d as

s NO

NONO

NOR

L 1

7. Enter up to 16 characters for the system name. For

example, NORTEL 1.

Registering individual portables / 91

P0881594 Issue 02 MICS-XC Norstar-Companion Installer Guide

• Press the dial pad key until the letter you need appears on

the display. Forexample, press key 5threetimes todisplay

the letter L.

• Press S

Eto add a blank space to the name.

• Press B

Pto delete the previous character.

• Press >if the next letter is on the same button.

8. Press S

E. The display shows the registered name. For

example, NO

NONO

NOR

L 1

1 r

9. Turn off registration for your system.

To confirm that the C3060 is registered

1. Select the system you just registered.

a. Press kto power off the portable, and press k

again to power on the portable.

If the display shows the system name that you just

registered, proceed to step 2.

Ifthe display shows a different system nameor N

o s

d, continue with the next step, sub-step b.

b. Press m*** .

c. Press S

d. Press ,or .until the display shows the system

name you just registered.

e. Press S

ELC

LCLC

LCT

T. Then press OK or END to exit

Administration.

2. Make a call.

a. Press i. You hear dial tone, and the display shows

LINK. If you do not hear dial tone, check that you have

selected the correct system or register the portable

again.

92 / Registering individual portables

MICS-XC Norstar-Companion Installer Guide P0881594 Issue 02

b. Dial the number of a working telephone. The telephone

must ring to confirm the registration.

3. Receive a call.

a. If the portable has the same extension number as a desk

telephone,make surethe desktelephone is idle and Call

Forward is not active.

b. On another working telephone, dial the telephone

number of the registered portable. The portable must

ring to confirm the registration.

If you donot hear dialtone, or ifthe portable does notring,

refer to “Troubleshooting” in Meridian Companion

Installation and Maintenance Guide. If you continue to

experience difficulty registering the portable, contact your

distributor.

Deregistering the C3060

You can deregister the C3060 in several ways:

• from the portable

• from the Administration Terminal (refer to Meridian

Companion Administration Terminal Operations Guide)

• from Companion Manager (refer to Companion Manager

Installation and Operations Guide)

Deregistering the C3060 from the portable clears registration

information stored in the portable and the system. For

example, you may want to deregister the portable before you

assign it to another WTN on the same system.

Deregistering the C3060 from the Administration Terminal or

from Companion Manager does not clear registration data

from the portable. (You could use this method if the portable

were lost or stolen or if you wanted to assign it to another

system.)

Registering individual portables / 93

P0881594 Issue 02 MICS-XC Norstar-Companion Installer Guide

If a portable is registered on other systems, it will still be

available on those systems. You deregister one system at a

time.

Note: If you are out of range of the system, this procedure

clears registration data only from the portable.

1. Press m***. The display shows A

ION

ONON

and three softkeys, SYS,PINFO,DATA.

2. Press S

S. The display shows W

S S

3. Press ERASE . The display shows Erase item? .

4. Press OK . The display shows Deregistering... and then

Item erased.

94 / Registering individual portables

MICS-XC Norstar-Companion Installer Guide P0881594 Issue 02

Measuring RSSI for a C3060

The Receive Signal Strength Indicator (RSSI) is a

measurement of the signal strength the Base Station receives

from the portable. The Base Station controls the power

transmitting mode of the portable. When the Base Station

receives a weak signal, it instructs the portable to transmit in

high-power. When the Base Station receives a strong signal, it

instructs the portable to transmit in low-power. The strongest

RSSI value the display shows is -35 dBm. The weakest RSSI

value the display shows is approximately -94 to -100 dBm.

Measuring undirected RSSI

You can measure the signal strength between a portable and a

system-selected Base Station using undirected RSSI.

1. Press m.

The display shows MENU.

2. Press ,or.until the displayshows Feature request

3. Press SELCT . The display shows A- .

4. Press *898. The display shows the cell

number, the radio ID of the Base Station to which the

portable is linked, the power mode (high or low), followed

by the signal strength and the channel. For example, 8

15112 H 67 29.

Registering individual portables / 95

P0881594 Issue 02 MICS-XC Norstar-Companion Installer Guide

You can alsopress ⁄ to view the informationin “standard”

display mode. This mode displays the radio ID of the Base

Station to which the portable is linked, followed by the

signal strengthand power mode. For example, 15112 - 67

H. You can revert back to the initial display mode by

pressing ƒ.

Hand-off occurs normally between the cells.

Note: In this example, the cell is 8, the card is 15, the port is

11, the radio is 2, and the channel is 29. The signal

strengthmeasured bythe Base Station is -67 dBm, and

the H indicates the portable is transmitting in high-

power mode (an L indicates low-power mode).

5. To end the connection, press k.

Measuring directed RSSI

You may want to measure the RSSI between a portable and a

specificBase Station radio. Forexample, youmay suspect that

one of the tworadios ina Base Stationis notworking properly.

You can also use directed RSSI to prevent hand-off while you

find a cell edge. To measure the RSSI of a specific radio, you

must be in range of two Base Stations—the one you want to

measure and another Base Station.

Note: You cannot measure thedirected RSSIof both radiosin

the Base Station at the same time.

Before you measure directed RSSI, use Meridian Companion

Programming and Provisioning Record to find and note the

following:

96 / Registering individual portables

MICS-XC Norstar-Companion Installer Guide P0881594 Issue 02

• The five-digit ID of the Base Station radio you want to

measure, bymapping theBaseStation locationto theTCM

port. The first four digits indicate the TCM port to which

the Base Station is connected. The last digit indicates the

number of the radio on the Base Station. For example, the

number 03142 on the Base Station is connected to TCM

port 0314, and 2 is the radio number. The five-digit

number might be printed on a label attached to the Base

Station mounting bracket.

• The radio IDs of all other Base Stations in the same

location.

1. Follow steps 1 to 5 of “Measuring undirected RSSI’’ on

page 94.

If the display shows the ID of a Base Station neighboring

the one you want to measure, proceed to step 2.

If the display shows the ID of the Base Station you want to

measure, move out of the cell boundary range so that hand-

off occurs and then continue with step 2.

2. Press m.The display shows MENU.

3. Press ,or .until the display shows Feature

request.

4. Press SELCT . The display shows A- .

5. Press *899.

6. Enter the five-digit ID code for the Base Station radio you

want to measure. The display shows the cell number, the

radioID ofthe BaseStation towhich the portable islinked,

the power mode (high or low), followed by the signal

strength and the channel. For example,

8 15112 H 67 29.

Registering individual portables / 97

P0881594 Issue 02 MICS-XC Norstar-Companion Installer Guide

You can alsopress ⁄ to view the informationin “standard”

display mode. This mode displays the radio ID of the Base

Station to which the portable is linked, followed by the

signal strengthand power mode. For example, 15112 - 67

H. You can revert back to the initial display mode by

pressing ƒ.

Hand-off does not occur as you move between the cell

boundaries. The link drops when you move out of range.

Note: In this example, the cell is 8, the card is 15, the port is

11, the radio is 2, and the channel is 29. The signal

strengthmeasured bythe Base Station is -67 dBm, and

the H indicates the portable is transmitting in high-

power mode (an L indicates low-power mode).

7. To end the connection, press m.

Registering the C3050

The following section describes the procedures involved in

registeringCompanionC3050 portabletelephones.Toregister

each portable with theNorstar system, you must dotwo things:

• Register the portables by entering the Registration

password on each one.

• Verify that the portable functions correctly.

C3050 Icons

Some C3050 portable telephone icons for Canada and the

United States are different but have the same functions. The

following table identifies these icons:

C3050 Canada Icon function C3050 US

Mute button µ

«Hang up button ´

98 / Registering individual portables

MICS-XC Norstar-Companion Installer Guide P0881594 Issue 02

To register the C3050

1. Turn on registration for your system.

2. Open the portable flap. The portable displays the current

system name or No system selected for two seconds.

3. Press Í. The portable displays WIRELESS SYSTEMS.

Your portable can be registered to a maximum of nine

different systems.

4. Press the ADD key to establish a radio link. The portable

displays Adding SYSTEM:# for two seconds, then it

displays Pswd:.

If a radio link is not established, the portable displays

No connection. Close the flap, and repeat the procedure

from step 1.

5. Enter the Registration password. The default is

¶™£¢§ (RADIO). The portable displays

DN:.

If the registration password is not correct, the portable

displays InvldPswd. Close the flap and repeat the

procedure from step 1.

6. Enter the DN (between 637 and 666). The portable

displays Enter name.

If the DN is incorrect, the portable displays Invld DN. If

the registration fails, the portable displays Reg failed.

If you try to register the C3050 to the same system twice,

the portable displays the registered name, for example

Registered as NORTEL 1.

æAnswer button Ò

Feature button Ï

ºTelephone directory button Î

C3050 Canada Icon function C3050 US

Other manuals for 3050

This manual suits for next models

Table of contents

Other Nortel Telephone manuals

Nortel

Nortel NORSTAR M7324 User manual

Nortel

Nortel Norstar M7100 Parts list manual

Nortel

Nortel BCM50 Quick guide

Nortel

Nortel T7208 User manual

Nortel

Nortel CallPilot 100 Setup guide

Nortel

Nortel Meridian Meridian 1 Operating and installation instructions

Nortel

Nortel M3905 Call Center User manual

Nortel

Nortel DMS-100 Series User manual

Nortel

Nortel DMS-100 Series User manual

Nortel

Nortel Meridian M5112 User manual

Nortel

Nortel IP 1120E User manual

Nortel

Nortel Norstar T7316E User manual

Nortel

Nortel Analog Telephone User manual

Nortel

Nortel Norstar M7100 User manual

Nortel

Nortel i2002 Parts list manual

Nortel

Nortel Meridian M3902 User manual

Nortel

Nortel Meridian M3902 User manual

Nortel

Nortel M7410 Instruction Manual

Nortel

Nortel BCM50 Instruction Manual

Nortel

Nortel Meridian SL-100 User manual

Nortel

Nortel Norstar ICS Specification sheet

Nortel

Nortel M5316 User manual

Nortel

Nortel T7100 User manual

Nortel

Nortel i2022 Series User manual

Popular Telephone manuals by other brands

GE 2-9480 user guide

Geemarc

Geemarc PHOTOPHONE 155 user guide

D-Link

D-Link DWR-720/PW user manual

Interquartz

Interquartz Gemini IQ333 operating instructions

SSS Siedle

SSS Siedle HT 840-0 operating instructions

Motorola

Motorola TITANIUM manual

Panasonic

Panasonic ICX Quick reference guide

LG H870DS user guide

Samsung

Samsung GT-I9500 Service manual

AT&T

AT&T Trimline 205 user manual

Selta

Selta zenyth 600 user guide

Doro

Doro AFTI 20 user guide

UNIQCELL

UNIQCELL A1 user guide

Panasonic

Panasonic KX Series User Sheet

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone manual

BT Decor 425 user guide

NEC

NEC SV8500 Reference sheet

Teledex

Teledex PEARL user guide