Nootools II Ballmagnet Instruction Manual
READ IN CONJUNCTION WITH INSTALLATION VIDEO AT WWW.BALLMAGNET.COM
INSTALLATION INSTRUCTIONS
PLEASE WATCH VIDEO:
www.ballmagnet.com
Congratulations on your new:
UNROLL NEATLY
PARALLEL TO NET
TIGHTEN. DO NOT
OVER-TIGHTEN
ALL POSTS
SHOULD BE
VERTICAL
PULL ON ENDS
WITH STRAPS
PICK UP,
ROTATE 90˚
& STRETCH OUT
LIFT OVER NET
AND DROP DOWN
EXTEND BLACK
CORDS
EXTEND
ADJUSTABLE
STRAPS
BLACK CORDS
INSTALLED
SHOULD BE
HORIZONTAL
BLACK CORDS
GO ON FIRST
KEEP POSTS
SEPARATE
WHITE CORD
WHITE CORD
CENTER LINE
NET
2
1
3
4
5
6
8
7
End Posts (4x)
White Line
Adjustment
Straps (2x)
2 Net Arrays (3x panels per array) Tethers (3x)
Fixed
Cords (2x)
Cord Lock Tensioner (6x total, 3x per side)
Center
Anchor Locks
Positioning Knots (2x per tether)
PRIOR TO INSTALLATION
• Do not unpack until ready to install
• Check contents
• No tools required
• We recommend 2 person installation
TWO PERSON INSTALLATION
(RECOMMENDED)
Remove from packaging.
Lay the spooled Ball Magnet close to
the tennis net on the center line.
• Ensure the end of the spool with the
white cord is closest to the tennis net.
Unroll both spools keeping it taut to avoid
risk of tangles.
• Ensure netting does not slip off the spools.
Find the black cords attached to the posts
on one end. Extend them.
• On the other end, extend the black straps.
Pick up the end posts, one in each hand,
stretch out the Ball Magnet and lift it over
the tennis net so poles are vertical.
• Check that the white cord is along the
bottom edge.
Separate the end posts so that each side of
the Ball Magnet can be lowered on to each
side of the tennis net.
FIRST Lower the end with the black cords
until posts are on the ground.
• Ensure the black cords are horizontal round
the tennis net pole and parallel.
• Check the end posts are
adjacent and vertical.
Stretch the other end into position
and lower posts.
• Tighten the straps enough to
prevent sagging but DO NOT OVER
TIGHTEN STRAPS.
• The Ball Magnet should follow the natural
line of the tennis net.
• If balls bounce off the Ball Magnet,
it may be too tight.
SECURE WITH STRAP
ROLL NEATLY MAINTAIN TENSION
AVOID TANGLING
FIGURE A 9” GAP
BALL
Panels
2-3” GAP
COURT NET
SET 2-2.5” OFF COURT SURFACE BALLS STAY CLOSE TO NET
SET 1-1.5” OFF COURT SURFACE MOST BALLS TRAPPED AGAINST NET
FIGURE C Adjust Cord Lock Tensioners (3x Per Side) To Raise Or Lower Ball Magnet.
BALL MAGNET SHOULD BE 2-3” ABOVE COURT FOR NORMAL PLAY.
MAIN NETCENTER
FIGURE B
FINAL ADJUSTMENTS
• As with any net, initial stretching may occur so check the tension
each day before play for the first few days.
• Check both sides are the same height and approx. 9” below
the tennis net tape. (FIGURE A)
• Optional: Add the cord lock tensioner to the center tether by passing
through tether loops. This keeps the Ball Magnet stable. (FIGURE B)
• Check the 3 series of nets are overlapping on both sides (like window blinds FIGURE A).
• Check the Ball Magnet™ is not too tight. It should have sufficient tension
to be horizontal but no more.
• Adjust height by using the cord lock tensioners on the 3 tethers (thin cords - FIGURE C)
SETTINGS
• Use the cord lock tensioners (3 on either side) on the top edge of the bottom
layer of netting to adjust height. This will retain balls 1-3' from the tennis net.
• SETTING A) Coaching, Cardio, Ball Machines:
Set the bottom of the Ball Magnet 2-2.5” above the court surface
• SETTING B) Match Play: Set the Ball Magnet 1-1.5” above the court surface.
This will trap balls at the base of the tennis net.
SINGLE PERSON INSTALLATION
* Follow above two person instruction
steps 1-6.
7. Lift the posts with the black cords over
one end of the tennis net pole.
8. Ensure the black cords are horizontal
and parallel round the tennis net pole.
9. Identify the three tethers on the top of
the Ball Magnet.
10. Lift the first up and onto the tennis
net so that each side of the Ball
Magnet drops on to either side
of the tennis net.
11. Repeat with the two remaining tethers.
12. Now grasp the remaining two posts
and pull them over and around the
tennis net pole.
13. Follow instructions above for final
adjustments.
STORAGE & REMOVAL
1. Loosen the straps around the tennis net
pole and lift Ball Magnet up and off the
tennis net while maintaining some
tension then Lay flat on court.
2. Grasp each end of the posts like a
rolling pin and roll each end carefully to
the middle. Maintain tension to achieve
tight spools and ensure no netting spills
over the spool ends.
3. Secure with string or strap and store in
included storage bag
MAINTENANCE is limited to
occasional checks:
1. Adjust the tension over the first few
days (and over time) as normal
stretching may occur.
2. Adjust the tension with the straps
around the tennis net pole. Again,
DO NOT OVER TIGHTEN.
3. Ensure the 3 layers of netting always
overlap evenly.
4. Check that the Ball Magnet is at the
same height on both sides of the
tennis net.
Thank you for your purchase. We hope the Ball Magnet improves your game!
Ball Magnet™, a Nootools II Company • Patent Pending, Copyright 2012, all rights reserved
Phone: 540-904-0887 • 55 St. John Place Suite 201 New Canaan, CT 06840 • Email: ser[email protected]
Table of contents
