NetApp AFF A250 User manual

AFF A250 systems

ONTAP Systems

NetApp

November 23, 2021

This PDF was generated from https://docs.netapp.com/us-en/ontap-systems/a250/install-setup.html on

November 23, 2021. Always check docs.netapp.com for the latest.

Table of Contents

AFF A250 System Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

Install and setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

Maintain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê11

AFF A250 System Documentation

Install and setup

Start here: Choose your installation and setup experience

For most configurations, you can choose from different content formats.

•Quick steps

A printable PDF of step-by-step instructions with live links to additional content.

•Video steps

Video step-by-step instructions.

•Detailed steps

Online step-by-step instructions with live links to additional content.

If your system is in a MetroCluster IP configuration, see the Install MetroCluster IP Configuration instructions.

Quick guide - AFF A250

This guide gives graphic instructions for a typical installation of your system from racking

and cabling, through initial system bring-up. Use this guide if you are familiar with

installing NetApp systems.

Access the Installation and Setup Instructions PDF poster:

•English: AFF A250 Installation and Setup Instructions

•Japanese: AFF A250 Systems Installation and Setup Instructions

•Chinese: AFF A250 Systems Installation and Setup Instructions

Videos - AFF A250

There are two videos; one showing how to rack and cable your system and one showing

an example of using the System Manager Guided Setup to perform initial system

configuration.

Video one of two: Hardware installation and cabling

The following video shows how to install and cable your new system.

Installation and Setup of an AFF A250

Video two of two: Performing end-to-end software configuration

The following video shows end-to-end software configuration for systems running ONTAP 9.2 and later.

NetApp video: Software configuration for vSphere NAS datastores for FAS/AFF systems running ONTAP 9.2

Detailed guide - AFF A250

This guide gives detailed step-by-step instructions for installing an AFF A250 system.

Step 1: Prepare for installation

To install your AFF A250 system, you need to create an account and register the system.

You also need to inventory the appropriate number and type of cables for your system

and collect specific network information.

You need to have access to the Hardware Universe for information about site requirements as well as

additional information on your configured system. You might also want to have access to the Release Notes for

your version of ONTAP for more information about this system.

NetApp Hardware Universe

Customers with specific power requirements must check HWU for their configuration options.

Find the Release Notes for your version of ONTAP 9

You need to provide the following at your site:

•Rack space for the storage system

•Phillips #2 screwdriver

•Additional networking cables to connect your system to your network switch and laptop or console with a

Web browser

1. Unpack the contents of all boxes.

2. Record the system serial number from the controllers.

3. Set up your account:

a. Log in to your existing account or create an account.

b. Register your system.

NetApp Product Registration

4. Inventory and make a note of the number and types of cables you received.

The following table identifies the types of cables you might receive. If you receive a cable not listed in

the table, see the Hardware Universe to locate the cable and identify its use.

NetApp Hardware Universe

Type of

cable…

Part number and length Connector

type

For…

25 GbE cable X66240A-05 (112-00595), 0.5m;

X66240-2 (112-00573), 2m

Cluster interconnect network

X66240A-2 (112-00598), 2m;

X66240A-5 (112-00600), 5m

Data

100 GbE cable X66211-2 (112-00574), 2m;

X66211-5 (112-00576), 5m

Storage

RJ-45 (order

dependent)

Not applicable Management network (BMC and

wrench port) and Ethernet data

(e0a and e0b)

Fibre Channel X66250-2 (112-00342) 2m;

X66250-5 (112-00344) 5m;

X66250-15 (112-00346) 15m;

X66250-30 (112-00347) 30m

Micro-USB

console cable

Not applicable Console connection during

software setup

Power cables Not applicable Powering up the system

5. Review the NetApp ONTAP Configuration Guide and collect the required information listed in that

guide.

ONTAP Configuration Guide

Step 2: Install the hardware

You need to install your system in a 4-post rack or NetApp system cabinet, as applicable.

1. Install the rail kits, as needed.

2. Install and secure your system using the instructions included with the rail kit.

You need to be aware of the safety concerns associated with the weight of the system.

3. Identify and manage cables because this system does not have a cable management device.

4. Place the bezel on the front of the system.

Step 3: Cable controllers

There is required cabling for your platform’s cluster using the two-node switchless cluster

method or the cluster interconnect network method. There is optional cabling to the Fibre

Channel or iSCSI host networks or direct-attached storage. This cabling is not exclusive;

you can have cable to a host network and storage.

Required cabling: Cable controllers to a cluster

Cable the controllers to a cluster by using the two-node switchless cluster method or by

using the cluster interconnect network.

Option 1: Cable a two node switchless cluster

The management, Fibre Channel, and data or host network ports on the controller

modules are connected to switches. The cluster interconnect ports are cabled on both

controller modules.

Contact your network administrator for information about connecting the system to the switches.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

1. Use the animation or the step-by step instructions to complete the cabling between the controllers and to

the switches:

Cabling a two node switchless cluster

Step Perform on each controller

Cable the cluster interconnect ports to each other with the 25GbE

cluster interconnect cable :

•e0c to e0c

•e0d to e0d

Cable the wrench ports to the management network switches with the

RJ45 cables.

DO NOT plug in the power cords at this point.

2. To complete setting up your system, see Step4: Completing system setup and configuration.

Option 2: Cable a switched cluster

All ports on the controllers are connected to switches; cluster interconnect, management,

Fibre Channel, and data or host network switches.

Contact your network administrator for information about connecting the system to the switches.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

1. Use the animation or the step-by step instructions to complete the cabling between the controllers and to

the switches:

Cabling a switched cluster

Step Perform on each controller

Cable the cluster interconnect ports to the 25 GbE cluster

interconnect switches.

•e0c

•e0d

Cable the wrench ports to the management network switches with the

RJ45 cables.

DO NOT plug in the power cords at this point.

2. To complete setting up your system, see Step4: Completing system setup and configuration.

Optional cabling: Cable configuration-dependent options

You have configuration-dependent optional cabling to the Fibre Channel or iSCSI host

networks or direct-attached storage. This cabling is not exclusive; you can have cabling

to a host network and storage.

Option 1: Cable to a Fibre Channel host network

Fibre Channel ports on the controllers are connected to Fibre Channel host network

switches.

Contact your network administrator for information about connecting the system to the switches.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Step Perform on each controller module

1 Cable ports 2a through 2d to the FC host

switches.

2 To perform other optional cabling, choose from:

•Option 2: Cable to a 25GbE data or host network

•Option 3: Cable the controllers to a single drive shelf

3 To complete setting up your system, see Step4: Completing system

setup and configuration.

Option 2: Cable to a 25GbE data or host network

25GbE ports on the controllers are connected to 25GbE data or host network switches.

Contact your network administrator for information about connecting the system to the switches.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Step Perform on each controller module

1 Cable ports e4a through e4d to the 10GbE host network

switches.

2 To perform other optional cabling, choose from:

•Option 1: Cable to a Fibre Channel host network

•Option 3: Cable the controllers to a single drive shelf

3 To complete setting up your system, see Step4: Completing system

setup and configuration.

Option 3: Cable the controllers to a single drive shelf

Cable each controller to the NSM modules on the NS224 drive shelf.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

1. Use the animation or the step-by-step instructions to cable your controller modules to a single shelf.

Cabling the controllers to a single NS224

Other manuals for AFF A250

Table of contents

Other NetApp Storage manuals

NetApp

NetApp DE5600 User manual

NetApp

NetApp H410S Manual

NetApp

NetApp EF550 User manual

NetApp

NetApp StorageGRID Webscale 10.4 Product manual

NetApp

NetApp FAS26 Series Manual

NetApp

NetApp AFF A400 User manual

NetApp

NetApp E Series User manual

NetApp

NetApp FAS500f User manual

NetApp

NetApp StorageGRID SD100 User manual

NetApp

NetApp FAS9500 Manual

NetApp

NetApp FAS2500 Use and care manual

NetApp

NetApp DS4486 Manual

NetApp

NetApp E Series User manual

NetApp

NetApp DS4243 Installation and maintenance instructions

NetApp

NetApp E-Series 3040 40U User manual

NetApp

NetApp StorageGRID SG5600 Series Operating manual

NetApp

NetApp FAS9500 User manual

NetApp

NetApp SG100 Instruction sheet

NetApp

NetApp AFF A200 User manual

NetApp

NetApp SolidFire C-Series Manual

NetApp

NetApp DE6900 User manual

NetApp

NetApp NearStore R100 User manual

NetApp

NetApp FAS500f User manual

NetApp

NetApp AltaVault Cloud Integrated Storage 4.1 Installation and maintenance instructions

Popular Storage manuals by other brands

QNAP

QNAP TS 32PXU Series user guide

LaCie

LaCie RUGGED RAID user manual

Freecom

Freecom CLS DOCK Quick install guide

PNY

PNY Attache P-FD64MBATT3 install guide

HP StorageWorks MSL2024 Getting started

OLT

OLT 6x6 Maximizer Assembly manual

Transcend

Transcend JetFlash 160 Specifications

LaCie

LaCie RUGGED MINI user manual

Thunderbolt

Thunderbolt 600 user manual

Panasonic

Panasonic LB-DH8 series Operator's guide

Intel

Intel RAID High Availability user guide

LaCie

LaCie 12big Thunderbolt 3 Quick install guide

Spectra Logic

Spectra Logic T-Series Spectra T50e quick start guide

Panasonic

Panasonic LKM-F931-1 instruction manual

Tabernus

Tabernus Enterprise Erase E2400 user guide

Rocstor

Rocstor COMMANDER 3F series user manual

HP P9000 user guide

Western Digital

Western Digital Ultrastar Data60 installation guide