National Instruments FIELDPOINT FP-1600 User manual
FieldPoint™ and natinst.com™are trademarks of National Instruments Corporation. Product and
company names mentioned herein are trademarks or trade names of their respective companies.
322395A-01 ©Copyright 1999 National Instruments Corp. All rights reserved. July 1999
OPERATING INSTRUCTIONS
FP-1600
FieldPoint 10/100 Ethernet
Network Module
These operating instructions describe the installation, features, and
characteristics of the FP-1600. For more detailed information on
using the network module, refer to the FP-1600 user manual.
Features
The FP-1600 is a FieldPoint network module with the following
features:
• Autonegotiating 10/100 Ethernet network interface
• Built-in high efficiency power supply powers I/O modules
• Network watchdog timer
• SnapShot capability and programmable power-up state
• –40 to +55 °C operation
• Connects to an Ethernet network using the TCP/IP protocol
• Supports up to nine I/O modules
• Runs on 11 to 30 VDC power
Kit Contents and Optional Equipment
Your kit contains the following items:
• FP-1600 network module
• Accessories: protective connector cover, two DIN rail stops,
Device Description diskette
You can order the following optional equipment from National
Instruments:
• Panel mount accessory, part number 777609-01
FP-1600 2 www.natinst.com
• Terminal bases and I/O modules, complete list of terminal
bases and I/O modules in the National Instruments online
catalog at www.natinst.com
•Cables
• 24 VDC power supply
Installation
Caution Toavoiddamagingthe FP-1600andthe terminal
bases, make sure that power is not applied to the FP-1600
while you install or remove terminal bases.
Follow these steps to install the FP-1600:
1. Use a flat-bladed screwdriver to open the DIN rail clip to the
unlocked position, as shown in Figure 1.
Figure 1. DIN Rail Clip
Note Write down the serial number from the back of
your FP-1600 before you mount your FP-1600. You will
need this information when you configure the FP-1600.
2. Mount the FP-1600 onto a 35 mm DIN rail or onto a panel
mount accessory.
• Installing onto a DIN rail:
a. Hook the lip on the rear of the FP-1600 onto the top of
a35 mm DIN railand press theFP-1600 downontothe
DIN rail, as shown in Figure 2.
Rail Clip LockedRail Clip Unlocked
© National Instruments Corp. 3 FP-1600
Figure 2. Mounting the FP-1600 onto a DIN Rail
b. Slide the FP-1600 to the desired position along the
DIN rail.
c. Lock the FP-1600 to the DIN rail by pushing the rail
clip to the locked position.
• Installing onto a panel mount accessory, which you can
order separately from National Instruments:
a. Snap the panel mount accessory onto the module,
as shown in Figure 3.
Figure 3. Mounting the FP-1600 onto a Panel Mount Accessory
Cover
Press
35 mm DIN Rail
Lip
Local Bus
Connector
Press
FP-1600 4 www.natinst.com
b. Lock the panel mount accessory into place by pushing
the rail clip to the locked position.
c. Mount the FP-1600 and panel mount accessory onto
the desired surface. You can drill pilot holes using the
directions in the FieldPoint Network Module Panel
Mount Accessory installation guide.
3. Add terminal bases with their local bus connectors firmly
mated to the FP-1600 local bus connector.
4. Place the protective cover over the local bus connector of the
last terminal base in the bank. Figure 4 shows an installed
FP-1600 network module on a DIN rail.
Figure 4. Installed Network Module
Network Connection
Connect the FP-1600 to an Ethernet network using the RJ-45
Ethernet port on the FP-1600. Connect the RJ-45 Ethernet port
of the FP-1600 to an Ethernet hub using a standard Category 5
Ethernet cable. You can also connect an FP-1600 directly to a
computer using an Ethernet crossover cable. Do not use a cable
longer than 100 m. Figure 5 shows the power and Ethernet
connectors on the FP-1600.
Protective
Cover
Local Bus Connectors
Firmly Mated
Rail Clip
Locked DIN
Rail
© National Instruments Corp. 5 FP-1600
Figure 5. Power and Ethernet Connectors on the FP-1600
Cabling
If you need to build your own cables, the following table shows the
standard ethernet cable wiring connections for both normal and
crossover cables.
Table 1. Ethernet Cable Wiring Connections
Pin Connector 1 Connector 2
(Normal) Connector 2
(Crossover)
1white/orange white/orange white/green
2orange/white orange/white green/white
3white/green white/green white/orange
4blue/white blue/white blue/white
5white/blue white/blue white/blue
6green/white green/white orange/white
7white/brown white/brown white/brown
8brown/white brown/white brown/white
Power Connector
FieldPoint Bank Status Indicators
RJ-45 Ethernet Port
Ethernet Status Indicators
FP-1600 6 www.natinst.com
Figure 6 shows the connector pinouts for FieldPoint Ethernet
cables.
Figure 6. Ethernet Cable
Powering the FP-1600
Caution Connect the FP-1600 to the terminal base before
applying power to the FP-1600 to avoid damaging the
FP-1600 or a terminal base.
Each FP-1600 on your network requires an 11–30 VDC power
supply. The FP-1600 filters and regulates this supplied power and
provides power for all the I/O modules in the bank. Therefore, you
do not need to provide power separately to each FieldPoint I/O
module in the bank. If your field I/O devices need to be powered
separately, you can use the terminals provided on each terminal
base for such power supply connections.
The power connector is a 6-pin screw terminal connector whose
pinout is shown in Figure 7.
Connector 1 Connector 2
pin 1 pin 1 pin 8pin 8
© National Instruments Corp. 7 FP-1600
Figure 7. FP-1600 Power Connector Pinout
Connect the primary power supply to the center V and C pair.
You can connect an optional backup power supply to the left V
and C pair. The right V and C pair provides a convenient means
of connecting power to the V and C terminals of a terminal base.
Figure 7 shows this optional connection.
Specifications
Network interface .............................10BaseT and 100BaseTX
Ethernet
Compatibility....................................IEEE 802.3
Communications rate........................10 Mbps, 100 Mbps,
autonegotiated
Cabling distance................................100 m
Power supply range...........................11 to 30 VDC
Power consumption...........................7 W + 1.15 * ∑(I/O module
power requirements)
Maximum terminal bases per bank...9
Maximum number of banks..............determined by network
topology
Operating temperature......................–40 to +55 °C
Storage temperature..........................–55 to +85 °C
Relative humidity..............................5% to 90% non-condensing
Weight...............................................250 g (8.7 oz.)
vvv
ccc
11-30 VDC
Backup Power
Supply
(optional)
+
–
+
–
11-30 VDC
Primary Power
Supply
V
C
To adjacent device
(optional connection)
Compliance
Electrical safety ................................designed to meet IEC 1010
EMI emissions/immunity..................CISPR 11
CE Mark Compliance
This product meets applicable EU directive(s) as follows:
EMC directive
Immunity....................................EN 50082–1:1994
Emissions ..................................EN 55011:1991 Group I
Class A at 10 meters
Mechanical Dimensions
Figure 8 shows the mechanical dimensions of the FP-1600.
Dimensions are given in inches [millimeters].
Figure 8. Mechanical Dimensions
4.31
[109.5]
3.60 [91.44]
4.22 [107.19]
Other manuals for FIELDPOINT FP-1600
2
Table of contents
Other National Instruments Network Hardware manuals
National Instruments
National Instruments DAQ 6527 User manual
National Instruments
National Instruments SCXI-1120 User manual
National Instruments
National Instruments GPIB-100A User manual
National Instruments
National Instruments NI WAP-3701 User manual
National Instruments
National Instruments NI Vision CVS-1450 Series User manual
National Instruments
National Instruments NI-9206 User manual
National Instruments
National Instruments PXI PXITM -1000 User manual
National Instruments
National Instruments SCB-68 User manual
National Instruments
National Instruments AT-232/2 User manual
National Instruments
National Instruments NI 9147 User manual
National Instruments
National Instruments SC-2040 User manual
National Instruments
National Instruments DAQ SCXI-1161 User manual
National Instruments
National Instruments PXIe-5663E User manual
National Instruments
National Instruments FIELDPOINT cFP-DO-403 User manual
National Instruments
National Instruments NI ELVIS III User manual
National Instruments
National Instruments IMAQ PCI-1411 User manual
National Instruments
National Instruments VXI-1394 User manual
National Instruments
National Instruments NI Vision CVS-1454 User manual
National Instruments
National Instruments NI 9375 User manual
National Instruments
National Instruments NI 9203 User manual
Popular Network Hardware manuals by other brands
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL product manual
B&B Electronics
B&B Electronics ZXT9-IO-222R2 product manual
Yudor
Yudor YDS-16 user manual
D-Link
D-Link ShareCenter DNS-320L datasheet
Samsung
Samsung ES1642dc Hardware user manual
Honeywell Home
Honeywell Home LTEM-PV Installation and setup guide
