National Instruments NI 9229 User manual
OPERATING INSTRUCTIONS AND SPECIFICATIONS
NI 9229/9239
4-Channel, ±60/±10 V, 24-Bit Simultaneous,
Channel-to-Channel Isolated Analog Input Modules
ni.com/manuals
DeutschFrançais
NI 9229/9239 2 ni.com
This document describes how to use the National Instruments 9229
and National Instruments 9239 and includes specifications and
terminal assignments. In this document, the NI 9229 and NI 9239
are referred to inclusively as the NI 9229/9239. Visit
ni.com/info and enter rdsoftwareversion to determine
which software youneed for the modules youare using. For
information about installing, configuring, and programming the
system, refer to the system documentation. Visit ni.com/info
and enter cseriesdoc for information about C Series
documentation.
Note The safety guidelines and specifications in this
document are specific to the NI 9229/9239. The other
components in the system might not meet the same safety
ratings and specifications. Refer to the documentation for
each component in the system to determine the safety
ratings and specifications for the entire system. Visit
ni.com/info and enter cseriesdoc for information
about C Series documentation.
© National Instruments Corp. 3 NI 9229/9239
Safety Guidelines
Operate the NI 9229/9239 only as described in these operating
instructions.
Hot Surface This icon denotes that the component may be
hot. Touching this component may result in bodily injury.
Safety Guidelines for Hazardous Voltages
If hazardous voltages are connected to the module, take the
following precautions. A hazardous voltage is a voltage greater
than 42.4 Vpk or 60 VDC to earth ground.
Caution Ensure that hazardous voltage wiring is
performed only by qualified personnel adhering to local
electrical standards.
Caution Do not mix hazardous voltage circuits and
human-accessible circuits on the same module.
Caution Make sure that devices and circuits connected to
the module are properly insulated from human contact.
NI 9229/9239 4 ni.com
Caution When module terminals are hazardous voltage
LIVE (>42.4Vpk/60 VDC), youmust ensure that devices
and circuits connected to the module are properly
insulated from human contact. Youmust use the NI 9971
connector backshell kit to ensure that the terminals are
not accessible.
Figure 1 shows the NI 9971 connector backshell.
Figure 1. NI 9971 Connector Backshell
© National Instruments Corp. 5 NI 9229/9239
Safety Guidelines for Hazardous Locations
The NI 9229/9239 is suitable for use in Class I, Division 2,
Groups A, B, C, D, T4 hazardous locations; Class I, Zone 2,
AEx nA IIC T4, and Ex nA IIC T4 hazardous locations; and
nonhazardous locations only. Follow these guidelines if youare
installing the NI 9229/9239 in a potentially explosive environment.
Not following these guidelines may result in serious injury or
death.
Caution Do not disconnect I/O-side wires or connectors
unless power has been switched off or the area is known
to be nonhazardous.
Caution Do not remove modules unless power has been
switched off or the area is known to be nonhazardous.
Caution Substitution of components may impair
suitability for Class I, Division 2.
Caution For Zone 2 applications, install the system
in an enclosure rated to at least IP 54 as defined by
IEC 60529 and EN 60529.
NI 9229/9239 6 ni.com
Caution For Zone 2 applications, install a protection
device between the input signal and the NI 9229/9239
input terminal. The device must prevent the input
channel-to-COM voltage from exceeding 85 V if there is
a transient overvoltage condition.
Caution For Zone 2 applications, connected signals must
be within the following limit:
Capacitance .......................... 0.01 μF max
Special Conditions for Hazardous Locations Use in Europe
This equipment has been evaluated as Ex nA IIC T4 equipment
under DEMKO Certificate No. 07 ATEX 0626664X. Each module
is marked II 3G and is suitable for use in Zone 2 hazardous
locations. If youare using the NI 9229/9239 in Gas
Group IIC hazardous locations or in ambient temperatures of
–40 °C ≤Ta ≤70 °C, youmust use the device in an NI chassis that
has been evaluated as EEx nC IIC T4, Ex nA IIC T4, or
Ex nL IIC T4 equipment.
© National Instruments Corp. 7 NI 9229/9239
Special Conditions for Marine Applications
Some modules are Lloyd’s Register (LR) Type Approved for
marine applications. To verify Lloyd’s Register certification, go to
ni.com/certification and search for the LR certificate, or
look for the Lloyd’s Register mark on the module.
Caution To meet radio frequency emission requirements
for marine applications, use shielded cables and install
the system in a metal enclosure. Suppression ferrites
must be installed on power supply inputs near power
entries to modules and controllers. Power supply and
module cables must be separated on opposite sides of the
enclosure and must enter and exit through opposing
enclosure walls.
NI 9229/9239 8 ni.com
Connecting the NI 9229/9239
The NI 9229/9239 provides connections for four simultaneously
sampled, isolated analog input channels.
Figure 2. NI 9229/9239 Terminal Assignments
AI0+
AI0–
AI1+
AI1–
AI2+
AI2–
AI3+
AI3–
0
1
0
1
0
1
0
1
© National Instruments Corp. 9 NI 9229/9239
The NI 9229/9239 has four 2-terminal detachable screw-terminal
connectors.
Note Youmust use 2-wire ferrules to create a secure
connection when connecting more than one wire to a
single terminal on the NI 9229/9239.
Yo ucan connect ground-referenced or floating signal sources to
the NI 9229/9239. Connect the positive signal of the signal source
to the AI+ terminal or connector, and connect the negative signal
of the signal source to the AI– terminal or connector. If youmake
a ground-referenced connection between the signal source and the
NI 9229/9239, make sure the voltage on the AI+ and AI–
connections are in the channel-to-earth safety voltage range to
ensure proper operation of the NI 9229/9239. Refer to the
Specifications section for more information about operating
voltages and overvoltage protection. Refer to Figures 3 and 4 for
illustrations of how to connect grounded and floating signal
sources to the NI 9229/9239.
NI 9229/9239 10 ni.com
Figure 3. Connecting a Grounded Signal Source to the NI 9229/9239
Figure 4. Connecting a Floating Signal Source to the NI 9229/9239
NI 9229/9239
Signal
Source
AI–
+
–
AI+
NI 9229/9239
Signal
Source
AI–
+
–
AI+
Other manuals for NI 9229
2
This manual suits for next models
1
Table of contents
Other National Instruments Network Card manuals
National Instruments
National Instruments NI 9217 User manual
National Instruments
National Instruments NI 9476 User manual
National Instruments
National Instruments Module SCXI-1503 User manual
National Instruments
National Instruments NI 6013 User manual
National Instruments
National Instruments Network Device DAQ S User manual
National Instruments
National Instruments NI 6232 User manual
National Instruments
National Instruments NI PXI-1056 User manual
National Instruments
National Instruments NI PCIe-8255 User manual
National Instruments
National Instruments NI 9475 User manual
National Instruments
National Instruments NI 9871 User manual
National Instruments
National Instruments NI 9403E User manual
National Instruments
National Instruments NI 9401 User manual
National Instruments
National Instruments NI 9426 User manual
National Instruments
National Instruments NI 9472 User manual
National Instruments
National Instruments NI 2590/2591 User manual
National Instruments
National Instruments NI 9264 User manual
National Instruments
National Instruments MXI Series User manual
National Instruments
National Instruments NI 9225E User manual
National Instruments
National Instruments NI 9235 User manual
National Instruments
National Instruments NI 9215 User manual
