Napoleon B35PG User manual

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.22D

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonﬁreplaces.com • [email protected]

SAFETY INFORMATION

!WARNING

If the information in these instructions are

not followed exactly, a ﬁre or explosion

may result causing property damage,

personal injury or loss of life.

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by a

qualiﬁed installer, service agency or the supplier.

CERTIFIED FOR CANADAAND UNITED STATES USING ANSI/CSAMETHODS.

$10.00

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁed kit is used.

Decorative Product: Not for use as a heating appliance.

BARRIER

CONFORMS TO AMERICAN NATIONAL STANDARDS: ANSI Z21.50, CERTIFIED TO CANADIAN CSA2.22 FOR VENTED GAS FIREPLACES.

HDX35

GLASS BURNER

ASSEMBLY

B35NG

NATURAL GAS

B35PG

PROPANE

W415-1452 / 06.08.15

A. Attach the burner assembly to the

ﬁrebox base with the screws supplied.

1.0 GENERAL INFORMATION

2.0 INSTALLATION

NOTE: Changes, other than editorial, are denoted by a line in the margin.

TABLE OF CONTENTS

A. Remove the door,

refer to installation

instructions. Remove

the 8 securing

screws and lift the

plate up and out

of the appliance.

Gasket may need

to be replaced if

damaged.

This glass burner assembly is approved for use in the HDX35 gas appliance only. It is not approved for use as

a stand alone appliance or in conjunction with any other appliance.

1.0 GENERAL INFORMATION 2

2.0 INSTALLATION 2

2.1 ACCESS PANEL 2

2.2 BURNER ASSEMBLY 2

2.3 BULKHEADS 3

2.4 MEDIATRAY 3

2.5 GLASS MEDIA 4

3.0 ADJUSTMENT 5

3.1 FLAME CHARACTERISTICS 5

3.2 VENTURI ADJUSTMENT 5

4.0 REPLACEMENTS 6

5.0 HDX35 ROCK BURNER 7

2.1 ACCESS PANEL

2.2 BURNER ASSEMBLY

INSIDE UNIT

NOTE: Install decorative panels before

burner assembly.

OUTSIDE

UNIT

W415-1452 / 06.08.15

Pilot

Electrode

Lead

Bulkhead

Venturi

Oriﬁce

NOTE: Bulkhead covers need to be removed,

refer to installation manual for removal

instructions.

A. Connect the main burner gas ﬂex line

and the pilot line to the gas ﬁttings on the

bulkheads located under the valve access

opening.Care must be taken to ensure the

pilot line is not kinked or damaged and

ensure gas tight connections are made.

2.3 BULKHEADS

B. Connect the pilot electrode lead to the

bulkhead matching the 3/16" ﬂag with the

3/16" bulkhead spade. Do the same with the

1/4" spark lead to the 1/4" bulkhead spade.

C. Ensure the venturi is inside the venturi

housing over the oriﬁce before lighting.

D. Check for gas leaks by brushing on a soap

and water solution. Do not use open ﬂame.

E. After leak test has been performed re-install

access panel with gasket.

2.4 MEDIA TRAY

A. Place the burner support over the pan burner

as shown below.

B. Align the holes in the media tray with the

holes in the pan burner. Secure with screws

supplied.

Main

Burner Gas

Connection

Pilot Tube

Gas Connection

MEDIATRAY

BURNER SUPPORT

BURNER

SUPPORT

NOTE: Air shutter adjustment can be made from

outside the ﬁrebox.

Spark

Lead

Venturi

Housing

W415-1452 / 06.08.15

PILOT

OPENING

Evenly spread the glass media onto the media tray, ensuring no glass media falls into the pilot opening. If this

happens, insert a clean bag into your vacuum cleaner and vacuum out the glass media. Replacement glass

can be purchased from your local authorized dealer / distributor.

NOTE: Do not use more media than what was supplied with the appliance.

CLEAN THE GLASS MEDIA PRIOR TO INSTALLATION. BEFORE APPLYING THE CLEANED GLASS, ENSURE

THAT IT IS DRY.

DO NOT CHANGE OR SUBSTITUTE THE GLASS MEDIA MATERIAL PROVIDED WITH THIS APPLIANCE. IF

REPLACING, USE ONLY THE REPLACEMENT GLASS MEDIA AVAILABLE FROM YOUR AUTHORIZED

DEALER / DISTRIBUTOR.

DO NOT PLACE ANY MEDIA (GLASS OR VERMICULITE) IN OR AROUND THE PILOT OPENING. THIS WILL

INTERFERE WITH THE PILOT OPERATION

WARNING

2.5 GLASS MEDIA

NOTE: The distribution of glass media over the burner ports will inﬂuence the ﬂame height. When the

ﬂames impinge on the glass, the glass may discolour slightly and the edges may soften.

CLEANING GLASS MEDIA

Glass media may have a ﬁne oil residue that needs to be cleaned prior to installation. Clean the glass with

mild dish soap, drain, rinse thoroughly and dry before placing over the burner.

74.2C

NOTE: Care must be taken to ensure there is no glass around the pilot opening.

W415-1452 / 06.08.15

3.0 ADJUSTMENT

3.1 FLAME CHARACTERISTICS

3.2 VENTURI ADJUSTMENT

It’s important to periodically perform a visual check of the pilot and burner ﬂames. Compare them to the

illustration provided. If any ﬂames appear abnormal call a service person.

FLAME MUST ENVELOP

UPPER 3/8” (9.5mm) TO 1/2”

(12.7mm) OF FLAME SENSO

PILOT

BURNER

ELECTRODE

FLAME

SENSOR

3/8” - 1/2”

(9.5mm - 12.7mm)

54.1B

Burner Air Shutter Openings

LOGS GLASS

LP 1/2" (13mm) 3/4" (19mm)

NG 1/4" (6mm) 1/4" (6mm)

OPEN

AIR SHUTTER

ADJUSTMENT

This appliance has an air shutter that has been factory set open according to the chart below:

Regardless of venturi orientation, closing the air shutter will cause a more yellow ﬂame, but can lead to carbon-

ing. Opening the air shutter will cause a more blue ﬂame, but can cause ﬂame lifting from the burner ports. The

ﬂame may not appear yellow immediately; allow 15 to 30 minutes for the ﬁnal ﬂame colour to be established.

AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED INSTALLER!

49.1

W415-1452 / 06.08.15

4.0 REPLACEMENTS

Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally

all parts can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE

ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FURTHER INFORMATION, CONTACT YOUR

AUTHORIZED DEALER. 41.1

FAILURE TO POSITION THE PARTS

IN ACCORDANCE WITH THIS

MANUAL OR FAILURE TO USE ONLY

PARTS SPECIFICALLY APPROVED

WITH THIS APPLIANCE MAY

RESULT IN PROPERTY DAMAGE OR

PERSONAL INJURY.

WARNING

ITEMS MAY NOTAPPEAR EXACTLYAS ILLUSTRATED

REF. NO. PART NUMBER DESCRIPTION

1BURNER ASSEMBLY GLASS

B35NG/PG INNER BASEW710-0073

FOR REPLACEMENT

PARTS REFER TO:

“B35NG GLASS BURNER”

W415-1452 / 06.08.15

44 W455-0068 PILOT ORIFICE #35 (LP) YES

ITEMS MAY NOTAPPEAR EXACTLY AS ILLUSTRATED

05.11.15 / A

REF. NO. PART NUMBER DESCRIPTION REF. NO. PART NUMBER DESCRIPTIONSTOCKED STOCKED

W335-0062 PILOT HOOD YES

W455-0070 PILOT ORIFICE #62 (NG) YES

W100-0183 BURNER ASSEMBLY

W456-0031 BURNER ORIFICE #31 (NG)

W456-0049 BURNER ORIFICE #49 (LP) YES

YES

W710-0073 GLASS MEDIA BOWL TRAY

W010-2997 MEDIA TRIM ASSEMBLY

W710-0075 GLASS MEDIATRAY

W500-0816 AIR SHUTTER PLATE

W350-0768 AIR SHUTTER HOUSING

W010-3646 AIR CONTROL CABLE

W350-0725 PILOT HOUSING 50

W720-0062 PILOT TUBE (w/ FITTINGS) YES

W240-0006 IGNITOR (w/ WIRE) YES

W245-0025 THERMOSENSOR YES

W010-2863 PILOTASSEMBLY (NG)

W010-2808 PILOTASSEMBLY (LP)

W655-0449 MEDIA SUPPORT

5.0 HDX35 ROCK BURNER

Other Napoleon®Products

'JSFQMBDF*OTFSUTt$IBSDPBM(SJMMT t(BT'JSFQMBDFTt8BUFSGBMMTt8PPE4UPWFT

)FBUJOH$PPMJOHt&MFDUSJD'JSFQMBDFTt0VUEPPS'JSFQMBDFTt(BT(SJMMT

'JSFQMBDFT)FBUJOH$PPMJOHDBMMt(SJMMTDBMM

napoleonproducts.com

/BQPMFPO3PBE#BSSJF0OUBSJP$BOBEB-.(

#BZWJFX%SJWF#BSSJF0OUBSJP$BOBEB-/:

.JMMFS%SJWF$SJUUFOEFO,FOUVDLZ64"

5SBOT$BOBEB)JHIXBZ.POUSFBM2VFCFD$BOBEB)5"

W415-1452 / 06.10.15

INSTALLATEUR : LAISSEZ CE MANUEL AVEC L’APPAREIL.

PROPRIÉTAIRE : CONSERVEZ CE MANUEL POUR CONSULTATION ULTÉRIEURE.

NE LAISSEZ PAS LES ENFANTS OU AUTRES INDIVIDUS À RISQUE SEULS À PROXIMITÉ DE L’APPAREIL.

1.22C

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Téléphone 705-721-1212 • Télécopieur 705-722-6031 • www.napoleonfoyers.com • [email protected]

CERTIFIÉPOURLECANADAETLES ÉTATS-UNIS SELON LES MÉTHODESANSI/CSA.

INSTRUCTIONS

D’INSTALLATION ET

D’OPÉRATION

APPOSEZ L’ÉTIQUETTE DU NUMÉRO DE SÉRIE DU CARTON

N° de série N° DE MODÈLE

10,00 $

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

AVERTISSEMENT

Une barriére conçu à réduire le risque de brûlures

causées par le verre chaud est fourni avec l’appareil

et sera installé pour la protection des enfants et

d’autres personnes à risque.

CONSIGNES DE SÉCURITÉ

AVERTISSEMENT

- N’entreposez pas et n’utilisez pas d’essence ou autres

liquides et vapeurs inﬂammables à proximité de cet ap-

pareil ou tout autre appareil.

- QUE FAIRE SI VOUS DÉTECTEZ UNE ODEUR DE GAZ :

• N’allumez aucun appareil.

• Ne touchez à aucun interrupteur électrique;

n’utilisez aucun téléphone dans votre immeuble.

• Appelez immédiatement votre fournisseur de gaz

d’un téléphone voisin. Suivez ses instructions.

• Si vous ne pouvez pas rejoindre votre fournisseur

de gaz, appelez le service des incendies.

- L’installation et l’entretien doivent être faits par un

installateur qualiﬁé, une agence d’entretien ou le

fournisseur.

Cet appareil peut être installé dans une maison

préfabriquée (mobile) déjà instalée à demeure si les

règlements locaux le permettent.

Cet appareil doit être utilisé uniquement avec le type de

gaz indiqué sur la plaque d’homologation. Cet appareil

ne peut être converti à d’autres gaz, sauf si une trousse

de conversion est utilisée.

Si ces instructions ne sont pas suivies à la

lettre, un incendie ou une explosion pourraient

s’ensuivre, causant des dommages matériels,

des blessures corporelles ou des pertes de vie.

Produit décoratif : Ne pas utiliser comme appareil

de chauffage.

ÉCRAN DE

PROTECTION

CONFORME AUX LES NORMES NATIONALES AMÉRICAINES: ANSI Z21.50, CERTIFIE CANADIENNES: CSA 2.22 FOYER À GAZ VENTILÉ.

HDX35

ASSEMBLAGE DU

BRÛLEUR POUR

BRAISES VITRIFIÉE

B35NG

GAZ NATUREL

B35PG

PROPANE

W415-1452 / 06.10.15

1.0 INFORMATION GÉNÉRALE

2.0 INSTALLATION

2.2 ASSEMBLAGE DU BRÛLEUR

NOTE : Les modiﬁcations, autres qu’éditoriales, sont indiquées par une ligne verticale dans la marge.

TABLE DES MATIÈRES

Cet assemblage de brûleur pour braises vitriﬁées est approuvé pour utilisation dans l’appareil au gaz HDX52-1

seulement. Il n’est pas approuvé pour utilisation comme appareil autonome ou avec n’importe quel autre appareil.

1.0 INFORMATION GÉNÉRALE 10

2.0 INSTALLATION 10

2.1 PANNEAU D’ACCÈS 10

2.2 ASSEMBLAGE DU BRÛLEUR 10

2.3 RACCORDS 11

2.4 PLATEAU 11

2.5 BRAISES VITRIFIÉES 12

3.0 RÉGLAGES 13

3.1 CARACTÉRISTIQUES DE LA FLAMME 13

3.2 RÉGLAGE DU VENTURI 13

4.0 RECHANGES 14

5.0 BRÛLEUR DES ROCHES 15

2.1 PANNEAU D’ACCÈS

A. Une fois que

vous avez enlevé

de la porte (voir

les instructions

d’installation),enlevez

le 8 vis de ﬁxation et

soulevez la plaque

et hors de l’appareil.

Joint d’étanchéité

être remplacé s’il est

endommagé.

INTÉRIEUR EXTÉRIEUR

NOTE: Installez des panneaux décoratifs

avant l’assemblage du brûleur.

A. Fixez le brûleur à la base de la chambrede

combustion à l’aide des 4 vis fournies.

This manual suits for next models

Table of contents

Languages:

Other Napoleon Indoor Fireplace manuals

Napoleon

Napoleon ZCVF36 User manual

Napoleon

Napoleon HD35PT-2 User manual

Napoleon

Napoleon EFL32H User manual

Napoleon

Napoleon NEFE27-0815W User manual

Napoleon

Napoleon GVF36P User manual

Napoleon

Napoleon Electric Fireplace EF30 User manual

Napoleon

Napoleon EF30G User manual

Napoleon

Napoleon HD35NT-1 User manual

Napoleon

Napoleon TORCH GT8P User manual

Napoleon

Napoleon NZ-26 User manual

Napoleon

Napoleon Madison GD80NT Installation instructions

Napoleon

Napoleon EF30S User manual

Napoleon

Napoleon CLEARion NEFBD50H User manual

Napoleon

Napoleon BHD4 PENINSULA User manual

Napoleon

Napoleon Entice 36 Series User manual

Napoleon

Napoleon EFL32H User manual

Napoleon

Napoleon GD82NT-PAE User manual

Napoleon

Napoleon B30NTR User manual

Napoleon

Napoleon NEFM33-0214 User manual

Napoleon

Napoleon GD15-N User manual

Napoleon

Napoleon BGNV40-N User manual

Napoleon

Napoleon GDS 50-N User manual

Napoleon

Napoleon Luxuria Series User manual

Napoleon

Napoleon 2113N User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions