MyOUTDOORKITCHEN SW-63 User manual
Content
Product Introduction......
Product Standards..........
Components.................
Installation..............
Safety Instructions.......
Handling
Application Instructions........
Maintenance...............
Trouble Shooting..........
１
１
２
３
4
5
6
7
8
Thank you for purchasing our
products, read carefully through the
instructions and keep the manual in a
safe place to facilitate your reference
at a later time.
SW-63
User Manual
Beverage Cooler
Lindström & Sondén AB
Havsbadsvägen 1, 262 63 Ängelholm, Sweden
EN
P roduct I ntroduction and S tanda rds
1
7.
8．
1. In order to guarantee the product's quality, this product applies advanced refrigeration
and manufacturing technology. In addition, strict comprehensive detection technology and a
range of imported equipment are being used.
2． High-quality compressors are used to support a wide temperature range of the
refrigerating system. Low power consumption.
3． The inside and outside of the cooler are made of stainless steel, therefore they are
corrosion-resistant and durable.
4． Transparent, tempered glass door with LED lightning lights up the cooler and displays its
content.
5. The cooler is equipped with a roll-bond evaporator which allows faster refrigeration.
6.
The transparent glass of the door prevents condensation and makes the contents of the
cooler easily visible.
The appliance is approved by CCC GS CE CB ETL RoHs etc.
The cooler is intended for private and commercial use.
Our company reserves the right to change the product. The appearance of the units that
you purchase might be slightly different from the anual, but it does not affect proper
and usage.
2
Components
3
Installation
Turn off the appliance and pull the power plug.
In case of problems with the compressor, the inclination shall not exceed 45°.
Please handle with care, the door is made of glass.
Remove the packing material and place the cooler on a flat and solid
surface.
Do not press on the glass door, the glass
could break.
Transport
Moving
Place the cooler in a location with good ventilation
Installation
Take out all goods
When moving the appliance, please empty it of all
contents to ensure that nothing can fall out.
In case of power failure or disconnection from the
mains, please plug in again after 5 minutes.
In case of power failure
5 min.
Ventilation
1. Pull back the door seal behind handle location.
2. Insert screws into pre-drilled screw holes.
3. Attach gasket.
4. Attach handle.
5. Tighten screws and press door seal back into place.
4
Handle Installation
Do not store close to flammable products
Flammable and explosive materials are not allowed to be
stored nearby the cooler. It is forbidden to store the cooler
close to dangerous goods.
Do not damage the power cord and power socket
Avoid touching the power cable. This may lead
to power failure and even fire.
Do not spray flammable liquids nearby the cooler
Do not spray flammable and explosive liquids
such as oil paint nearby the cooler.
Should be equipped with specialized power socket and fuse
For normal use, the voltage should be according to the
nameplate, and the power socket should have a
reliable ground conductor.
This may lead to overheating and even fire.
Do not connect several appliances to one socket
Do not store any electrical appliances in
the cooler
Do not store any electric appliances in the
cooler, otherwise it may cause danger.
5
Safety Instructions
1、
1.1
Settings
Before connecting the power, please check
the power cord, the light switch and the thermostat
switch knob.
1.2 Temperature setting:
The temperature setting has 1~6 gears, the
first is the highest temp. and the sixth is
the lowest temp. You can adjust according
to your needs.
1.3 Light setting:
Use the ON/OFF button to turn the LED lighting on
or off.
6
Handling
1. Damaged power cords should only be repaired by certified service technician.
2. Do not touch the compressor, the surface can get hot.
3. Do not hang anything on the door as the appliance may tip over.
4. Please keep the appliance clean on its in- and outside, otherwise the cooling effect may be affected.
5. If the appliance will not be used for an extended period of time, please follow instructions below:
1) Unplug the power plug and take out all of the items inside the appliance.
2) Clean the inside and outside of the appliance and dry it carefully.
3) Keep out of the reach of children, to make sure that children cannot enter the appliance.
6. Do not damage the refrigeration cycle pipe. The pipe runs inside and outside the
appliance. If the pipe is damaged, the refrigeration cycle could get interrupted.
7
Application Instructions
1. Clean the inside and outside of the products thoroughly.
1) Use a soft cloth to clean the cooler, you may even use a bit of mild detergent, and wipe dry with a soft dry cloth.
2) Please clean and maintain the cooler regularly.
2. Attention:
1) For safety, please disconnect the cooler from power before cleaning.
2) Do not directly flush with water.
3) Clean regularly. Plastic parts such as the door gasket, door frame etc. can be
damaged by exposure to refrigeration oil vapour for a long period of time.
4) The following liquids and substances can damage the surface of the
appliance:
Alkaline detergent, toilet soap, abrasives, boiling water, sweeper, lacquer
thinner, acetone, methylbenzene etc.
8
Maintenance
If the fault cannot be eliminated through inspection, please contact the
manufacturer or a service technician.
Trouble Shooting
Problem Solution
Appliance not working Is the power cord plugged in?
Cooling problem
Broken fuse?
No power?
No good ventilation?
Heat source close to the appliance?
Door does not close properly or stands open for too long?
Door gasket is not tight or deformated?
Too many bottles on the same shelf?
Air inlet or outlet is blocked?
Wrong settings?
Not enough space for ventilation on the right & left side?
Noisy
Appliance is not placed on a flat surface?
Appliance touches a wall?
Loose or missing parts?
9
Trouble Shooting
Table of contents
Languages:
