Mylek MYRA600W User manual
User Manual -
Please read and retain
for future reference
www.hsdonline.co.uk
MYRA600W
MYRA900W
MYRA1200W
MYRA1500W
PROGRAMMABLE TIMER
HEATER
WITH LCD SCREEN
&REMOTE CONTROL
DAY
DAY
7
7
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 1
Contents
2. CONTENTS
3. INTRODUCTION
4. GENERAL SAFETY INSTRUCTIONS
6. INSTALLATION AND MOUNTING
10. CONTROL PANEL
10. LCD SCREEN
10. OPERATION
Operating instructions
Locking / Unlocking
Using the heater
Manual use
Changing the selected temperature
Switching off
Automatic use (programmed)
14. FAQ
15. POWER CUTS
15. SAFETY
15. RECOMMENDATIONS
15. MAINTENANCE
16. INFORMATION REQUIREMENT FOR THE ELECTRIC LOCAL
SPACE HEATERS
20. PAT TESTING
20. ENVIRONMENTAL RESPONSIBILITIES
20. SERVICE WARRANTY
www.hsdonline.co.uk
2
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 2
Introduction
General Information
Please read the entire instruction manual before using the product and
then save it for future reference. We reserve the right for any errors in
text or images and any necessary changes made to technical data. If you
have any questions concerning technical problems please contact our
Customer Services on 0800 091 3171.
Safety Instructions
General safety instructions for heaters:
Warning: Read all the instructions. Failure to comply with
the following instructions can lead to electric shocks,
fires or serious injury.
SAVE THESE INSTRUCTIONS.
ERP Compliant
Good News your product is ErP Compliant, ErP stands for “Energy
Related Products”. ErP is supported by Mylek to makethe use of energy
and energy related products more efficient, by phasing out inefficient
products and making it easier for consumers to find energy information,
providing guidance to more energy efficient products.
Your heater is fitted with a ERP Compliant sensor that detects a sudden
drop in temperature, meaning there could be a open window or draft,
when the sudden drop in room temperature is detected your heater
quickly increases the display room temperature to your set temperature
to switch the heater off to save energy, once the heater senses a natural
rise in room temperature (meaning the window as been shut or draft
eliminated) it drops the display room temperature back down to normal
room temperature to switch the heater back on again. Making your Mylek
heater energy efficient and great for the environment.
www.hsdonline.co.uk 3
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 3
www.hsdonline.co.uk
GENERAL SAFETY INSTRUCTIONS
•Remove the plug from the mains power socket to disconnect the heater. Do NOT
pull on the cable.
•Do not leave the mains cable in contact with the heater when it is switched on.
•During operation, ensure that the heater is kept well away from combustible
materials such as curtains, carpets and furniture, etc.
•DO NOT COVER THE HEATER. DO NOT USE THE HEATER TO DRY
CLOTHES.
If the heater is covered, there is serious risk of overheating.
•DANGER: If the mains cable is damaged, it must be replaced by the
manufacturer or by its after-sales service, by fully qualified personnel
in order to prevent any hazardous situations.
•If the heater is to be installed in a bathroom, it must be installed by a qualified
electrician in volume 3 (Figure 2, page 6).
•The heater must not be located under or in front of a mains socket.
•When disposing of the heater, all requirements established by current
legislation for waste processing and recycling must be followed.
•The installation must be carried out according to current electrical legislation.
•This heater must have an earth connection.
•The heater must be installed so that the mains plug is always accessible.
•This heater cannot be flush-mounted in a wall. Always respect the safety
distances (Figures 3 and 4).
*Alocking system is fitted to prevent children from playing with the heater
programming.
•This heater is not designed to be handled by children or physically, mentally or
sensory handicapped persons, with little experience or knowledge, unless
under the supervision of a person responsible for their safety and in
possession of the corresponding instructions on use. Children must be
supervised to ensure they do not play with the heater.
*Children under 3 years must be kept well away from the heater unless under
constant supervision.
*Children of less than 3 years should be kept away unless continuously
supervised. Children aged from 3 years and less than 8 years shall only switch
on/off the appliance provided that it has been placed or installed in its intended
normal operating position and thy have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
4
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 4
www.hsdonline.co.uk
*This appliance may be used by children age 8 and over and by persons with
physical, sensorial or mental disabilities or without experience or knowledge,
provided they have been duly trained and are supervised by somebody who
understands the hazards. The cleaning and maintenance to be carried out by
the user must not be done by children. Children should not play with the
appliance.
•PRECAUTION: Certain parts of this heater may become very hot
during operation and cause burns. Special care must be taken when
children and other vulnerable persons are present.
•PRECAUTION: Keep bags and other accessories well out of the reach
of children.
•Do not touch the outside of the heater during operation.
•It is quite normal to notice a smell of “something new” when the heater is
switched on for the first time”. Allow your heater to work in a well-ventilated area
for two or three hours.
•Before each cold season or if the heater has been switched off for several
days/months, it should be cleaned before switching it on again (follow the steps
in “section 10 Maintenance”). This cleaning will prevent the burning of
accumulated dust and other remains.
•This heater CANNOT be operated with external programmable units or any
other third party control device.
•Owing to the convection effect of this heater, together with other external
factors, discolouration of metal and other surfaces can be caused if in proximity
to the heater. This can cause discolouration of metal and plastic surfaces.
•Temperature fluctuations may cause crackling or heater noises. This is not an
indication of failure.
*The heater warranty does not cover any damage caused by failing to follow
these instructions.
5
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 5
www.hsdonline.co.uk
INSTALLATION AND
MOUNTING
•This heater can be installed on feet
(provided) or wall mountable (fixings
provided).
•The heater must never be installed
underneath a mains wall socket.
•The heater must never be installed in
aposition where the switches and
other controls can be reached by
someone in the bath or shower.
•The heater works through natural air
convection. In order to achieve
correct performance and uniform
heat distribution, when it is installed
on a wall the lower part of the heater
must be at a minimum distance of
twenty centimetres from the floor and
aminimum distance of twenty
centimetres from the sides and fifty
centimetres from an upper shelf and
also a minimum distance of twenty
centimetres from any wall or object
(furniture and curtains etc).
6
Aqualified electrician can
install your heater in volume
3in the bathroom (Figure 2).
It must not be possible to
reach it from the bath or
shower.
IMPORTANT
Fig. 1
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 6
www.hsdonline.co.uk
WALL INSTALLATION:
1. Select a suitable location on the wall,
which should be firm and level. Check
that there is a mains socket close by.
2. The distances marked, “a” and “e”
vary depending on the heater model.
Safety distances and installation
Models a(mm) b(mm) e(mm) f(mm)
MYRA600W 410 93 140 495
MYRA900W 550 93 280 495
MYRA1200W 690 93 420 495
MYRA1500W 830 93 560 495
3. Open the package box and check
that all fixing accessories are
present, it is a good idea to keep the
product box for out of season
storage.
7
AB
CD
EF
Feet
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 7
www.hsdonline.co.uk
ASSEMBLY
1. While respecting the previously
indicated safety measurements, make
two marks on the wall according to
measurement “e” indicated in Table 1
and at a height of 695 mm from the
floor (not from the skirting board).
2. At the marked area drill two 10-mm
diameter holes, with a minimum depth
of 60 mm.
3. Push the two plugs (D) into the two
holes and secure the two hooks (C)
with the two screws (D). (Figure 6 & 7).
4. Screw the two support brackets (A) (or
one support bracket, depending on
the model) to the rear part of the
heater with the four screws (E) (or two
screws, depending on the model).
Note: The two brackets (A) are screwed
to the holes located on the lower rear
part of the heater, at both ends.
(Figure 8).
8
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 8
www.hsdonline.co.uk
5. Hang the heater on the two hooks (C)
on the wall. Ensure that the heater is
correctly secured on both hooks.
(Figure 9).
6. When the heater is hung in place,
make two marks on the wall where the
two brackets (A) will be fixed to ensure
the heater is fixed to the wall.
(Figure 10).
7. Remove the heater and drill two 4-mm
diameter holes, with a minimum depth
of 25 mm at the two marks on the wall.
8. Insert the two plugs and secure
with the two screws (B) to completely
secure the heater to the wall.
(Figure 11).
INSTALLING THE FEET:
1. Screw the two feet to the lower rear
part of the heater with the four screws
provided (F), 2 screws per foot.
(Figure 12).
9
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 9
www.hsdonline.co.uk
CONTROL PANEL
LCD SCREEN &
REMOTE CONTROL
The screen comes on for ten
seconds every time a button is
pressed and then dims as a
energy saving function.
The heater can be programmed by
either the LCD control section on
the heater or by the remote control.
(1) CONSUMPTION INDICATOR
This appears when the heater is
consuming power, in other words, in
operation.
(2) TEMPERATURE INDICATOR:
•Ambient room temperature reading:
that of the room, it is displayed on all
screens by default.
•Assigned temperature: programmed
by the user as the desired
temperature for COMFORT MODE,
ECONOMY MODE OR ANTI-FROST
MODE. To display this temperature
press the (-) or (+) button.
OPERATION
•Your heater is fitted with a digital,
daily-programmable timer-thermostat
that controls and adjusts the heating.
•The heater can be used in two ways,
either manually or automatically. It is
fitted with a daily timer for each day of
the week.
IMPORTANT:
The temperature indicated on the
screen may differ from that given by
another thermometer in the same room.
Different conditions such as air
currents, windows etc, could cause
these differences.
10
Standby
Comfort Mode
Economy Mode
Anti-frost Mode
LCD Screen
IR Sensor
“Prog” Button
Increase
Decrease
Remote Control
MYLEK_heater_Manual_2018 6/6/18 16:42 Page 10
This manual suits for next models
3
Table of contents
Other Mylek Heater manuals
Mylek
Mylek MY0210R User manual
Mylek
Mylek MHPH05-10E User manual
Mylek
Mylek MYOD606WH User manual
Mylek
Mylek MYBH1000 User manual
Mylek
Mylek MYSH0406E User manual
Mylek
Mylek SPH05-05R User manual
Mylek
Mylek MYH03-05E User manual
Mylek
Mylek MYTH01D User manual
Mylek
Mylek MYHH0406C User manual
Mylek
Mylek MYC01-10A User manual
Popular Heater manuals by other brands
oventrop
oventrop Regucor Series quick start guide
Blaze King
Blaze King CLARITY CL2118.IPI.1 Operation & installation manual
ELMEKO
ELMEKO ML 150 Installation and operating manual
BN Thermic
BN Thermic 830T instructions
KING
KING K Series Installation, operation & maintenance instructions
Empire Comfort Systems
Empire Comfort Systems RH-50-5 Installation instructions and owner's manual
Empire Heating Systems
Empire Heating Systems WCC65 Installation and owner's instructions
Wetekom
Wetekom 92 86 43 Original instructions
Desa
Desa SPC170-F owner's manual
Watlow
Watlow Watrod Electric Tubular Heaters Specifications
Haverland
Haverland ECO-DRY GPS Series Instruction & installation manual
Stelpro
Stelpro ASILVC2060 Series user guide