MuxLab 500115 User manual
© MuxLab Inc.
94-000870-A
SE-000870-A
© MuxLab Inc. 2017
8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: videoease@muxlab.com URL: www.muxlab.com
Specifications
Environment
PoE CCTV IP
Devices
PoE CCTV IP cameras with a 10/100Mb/s Ethernet port, using up to 30
Watts.
Transmission
Transparent to the user
Standard supported
Ethernet side:
IEEE 802.3 10BaseT,
IEEE 802.3U 100Base-TX
IEEE 802.3af/at compatible PoE
PoE Power
Class 3
Connectors
One (1) BNC 75 Ohms.
One (1) RJ45Sfor Cat 5e/6 unshielded or shielded twisted pair.
LED Indicators
Power, IP Traffic, 100MBps
Maximum Distance
RG6: Up to 1969ft (600m) @ 100Mbps (with PoE)
Up to 3281ft (1000m) with IP only (without PoE)
UTP Cat 5e/6: Up to 330ft (100 m)
Note:When installed in an electrically noisy environment, an STP
cable must be used. Also, cross-connection reduces the effective
distance depending on the grade of twisted cable used.
RJ45 Pin
Configuration
Reverse Polarity
Sensitive. Use EIA/TIA
568A or 586B straight-
through wiring.
RJ45 Link
Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)
Cable
UTP/STP: One (1) Cat 5e/6 or better twisted pair cables required
RG59/RG6:75 Ohms (avoid CCS cable)
Power Supply
Optional Power Supply (110-240V/56VDC) min.65W (sold separately).
Required at the Camera Side Device when coax cable quality or
length results in insufficient power reaching the camera. Required
at the Network Side Device when used in a non-PoE environment.
Power Consumption
Network Side: 3.2 Watt Camera Side: 3.0 Watt
Temperature
Operating: 0° to 60°C Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Enclosure
Metal
Dimensions
3.54/3.11” x 1.65” x 0.87” (90/79 x 42 x 22 mm)
Weight
0.78 lb (0.354 kg)
Compliance
Regulatory: FCC, CE, RoHS Flammability: 94V0
Warranty
2 years
Order Information
500115CCTV IP PoE Extender Kit, 600m
Accessories
500116-(US/UK/EU) 56VDC 65W PSU (sold separately)
LongReach CCTV IP PoE
Extender Kit, 600m
500115
Quick Installation Guide
Overview
The LongReach CCTV IP PoE Extender Kit, 600m (500115) allows one IP camera (up
to 30 Watts) to be connected up to 1969ft (600m) via a single 75-ohm coax cable in a
point-to-point configuration. The maximum distance depends on the grade and quality
of coaxial cable used, and if PoE is used. An optional 56VDC (65W) Power Supply
(sold separately) can be used if required, which also helps to extend distance.
Applications
CCTV IP surveillance
Installation
1. Identify the connectors on the Extenders as indicated on the product labels.
2. Position each unit in the intended installation location.
© MuxLab Inc. 2017
© MuxLab Inc. 2017
3. Verify that the distance between the CCTV IP PoE extenders is within MuxLab
specifications (see Specifications table).
4. To install the Network Side Device:
4a. Connect the extender to the PoE Ethernet Switch with a UTP Cable.
Note: If the Ethernet Switch is not PoE; you will need to connect an optional
56VDC (65W) Power Supply (sold separately) to the Network Side Device.
4b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX
LINK connector on the Extender.
5. To install the Camera Side Device:
5a. Connect the extender to the camera with a Cat5e/6 cable.
Note: If the quality or length of the coaxial cable reduces the power to a level
that is insufficient to power the camera, you will need to connect a separate
48-56VDC (with appropriate wattage, depending on camera) Power Supply to
the Camera Side Device.
5b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX
LINK connector on the Extender.
6. Power on the equipment and verify the image quality. The following is a diagram
of a typical configuration.
Tables
Typical resistance for RG59 is 17Ω/100m, RG6 is 13Ω/100m and RG11 is 4.9Ω/100m
Troubleshooting
The following table describes some of the symptoms, probable causes and possible solutions
in respect to the installation of the LongReach CCTV IP PoE Extender Kit, 600m:
Symptom
Network Side
LEDs
Camera Side
LEDs
Probable Cause
Possible
Solutions
Power
IP Traffic
Power
IP Traffic
No Image
OFF
OFF
OFF
OFF
No power
•Check if the Ethernet
switch is PoE.
•Check the power
connection.
No Image
ON
OFF
OFF
OFF
Coaxial Cable
•Check the coaxial
cable.
No Image
ON
OFF
OFF
OFF
Distance
•Check the coaxial
cable length and
quality.
No Image
ON
OFF
ON
OFF
UTP Cable
•Check the UTP Cable
pin out.
No Image
ON
ON
ON
ON
No Traffic
•Check network
configuration.
Choppy Image
ON
BLINK
ON
BLINK
Distance
•Check cable length
•Check the coaxial
cable quality.
If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).
Table of contents
Other MuxLab Extender manuals
MuxLab
MuxLab 500460 User manual
MuxLab
MuxLab 500454-POE User manual
MuxLab
MuxLab 500771 User manual
MuxLab
MuxLab 500041-WP-UK User manual
MuxLab
MuxLab 500451-TX User manual
MuxLab
MuxLab 500451-PoE User manual
MuxLab
MuxLab 500732 User manual
MuxLab
MuxLab 500449 User manual
MuxLab
MuxLab 500417 User manual
MuxLab
MuxLab 500754 User manual
MuxLab
MuxLab 500759-TX-HLO User manual
MuxLab
MuxLab DomoStream User manual
MuxLab
MuxLab 500040 User manual
MuxLab
MuxLab 500771 User manual
MuxLab
MuxLab 500456 User manual
MuxLab
MuxLab Pro Digital 500452 User manual
MuxLab
MuxLab 500752 User manual
MuxLab
MuxLab 500070 User manual
MuxLab
MuxLab 500759-TX-Dante User manual
MuxLab
MuxLab 500460-RX User manual
Popular Extender manuals by other brands
foxunhd
foxunhd SX-AEX01 operating instructions
TERK Technologies
TERK Technologies LFIRX2 owner's manual
Devolo
Devolo Audio Extender supplementary guide
Edimax
Edimax EW-7438RPn V2 instructions
Shinybow USA
Shinybow USA SB-6335T5 instruction manual
SECO-LARM
SECO-LARM ENFORCER EVT-PB1-V1TGQ installation manual