MULTIQUIP UWKB User manual
UWKB — WHEEL KIT INSTRUCTIONS P/N UWKB01 — REV. #0 (02/03/12) — PAGE 1
UWKB Wheel Kit
For Use on Portable Generators, Pumps, and Welders
The following instructions are intended to assist the user in the assembly of the UWKB Wheel Kit for use on Multiquip
portable generators, pumps, and welders. Please read the entire instructions before assembling the wheel kit.
REQUIRED TOOLS
Ratchet Set with 10 mm socket
Adjustable Wrench or 10 mm open-end wrench
Pliers
PARTS
Verify that all parts are accounted for. See Table 1.
WORK SAFELY!
Only a qualified service technician with proper training
should perform this installation. Follow all shop safety rules
when performing this installation.
Table 1. UWKB Wheel Kit Parts
Item
No. Part No. Description QTY. Remarks
1 WK1312 Wheel/Tire, Solid 2
2 8158 Pin, Cotter 3/16D x 1-1/2 2
3 29748 Axle Mount W/A, Left (3 5/8") 1
4 29749 Axle Mount W/A, Right (3 5/8") 1
5 WK34715 Screw, M6 x 45 4
6 0948 Washer, Flat SAE1/4 24
7 WK34717 Nut, Nyloc M6 12
8 WK2250 Clamp, Small 4
9 WK2300 Clamp, Large 4
10 29787 Pin, Clevis 5/16 x 1-1/2 2
11 0300 B Washer, Flat SAE 5/16 4
12 0683 Pin, Cotter 3/32D x 3/4 2
13 29739 Tube, Handle 2
14 19717 Grip, Hand 2
15 29746 Handle Mount W/A 2
16 4001 Washer, Flat USS 3/8 PLD 2
17 19716 Crutch Tip 2
18 WK34716 Screw, HHC M6 x 90 8
PROCEDURE
1. Assemble the axle mounts (See Figure 1). Push the
wheel (item 1) on the axle mount (item 3) and then
insert the cotter pin (item 2) through the outer axle
hole. Bend the cotter pin to secure the wheel in place.
Repeat this step for the other axle mount (item 4).
Figure 1. Axle Mount Assembly
2. Turning your unit on its side, or while having a second
person lifting the side in the air, place the axle mount
under the frame tubing on the side of the unit as shown
in Figure 2.
Figure 2. Securing Axle Mount to the Frame
NOTICE
Axle Mount Length is 3 5/8 inches.
5
6
7
9
3
7
6
8
18
UWKB — WHEEL KIT INSTRUCTIONS P/N UWKB01 — REV. #0 (02/03/12) — PAGE 2
3. Set the rounded corner of the tubing in the bracket at
the back of the axle mount and place a screw (item 5)
and flat washer (item 6) through the holes, securing
the tubing in place. Place another flat washer and a
nyloc nut (item 7) on the threaded end of the screw
and tighten.
4. Secure the axle mount to the frame tubing by placing
a small clamp (item 8) over the frame tubing and the
axle mount. Place a large clamp (item 9) over the small
clamp. Insert screw (item 18) into the small clamp and
secure with nyloc nut (item 7) and washer (item 6).
Tighten screw until the clamp securely holds the axle
mount to the frame tubing.
5. Repeat steps 2 through 4 to attach the axle mount to
the opposite side of the unit.
6. Insert a flat washer (item 16) into the crutch tip (item 17)
and place the combined items over the open end of
the handle mount (item 15). See Figure 3.
Figure 3. Handle Mount Assembly
7. Insert the end of the handle tube (item 13) with the
screw hole into the top bracket of the handle mount.
Slide a clevis pin (item 10) and flat washer (item 11)
through the bracket and handle tube holes. Place
another flat washer on the end of the clevis pin. Insert
a cotter pin (item 12) through the hole in the clevis pin
to secure the handle tube to the handle mount.
8. Slide the hand grip (item 14) over the open end of the
handle tube.
NOTICE
Attach the axle mounts so that the wheels are located
under the heaviest end of your unit. The placement of
the axle mounts may differ on each type of equipment.
9. Lifting the front of the unit, set the rounded corner of
the frame tubing into the support bracket on the handle
mount (Figure 4). Secure the handle mount to the
frame tubing by placing a large clamp (item 9) around
the frame tubing and the handle mount. See Figure 4.
Figure 4. Securing Handle Mount to the Frame
10. Insert the small clamp (item 8) on the other side of the
handle mount and frame tubing, so that the large and
small clamps are facing each other.
11. Insert screw (item 18) into small clamp and secure
with nyloc nuts (item 7). Tighten screw until the clamp
securely holds the handle mount to the frame tubing.
12. Repeat steps 9 through 11 to attach the handle mount
to the other side of the unit.
7
LARGE
CLAMP
SMALL
CLAMP
8
18
PUMP
FRAME
9
6
HANDLE
MOUNT
6
UWKB — WHEEL KIT INSTRUCTIONS P/N UWKB01 — REV. #0 (02/03/12) — PAGE 3
NOTES
Your Local Dealer is:
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
United StateS
Multiquip Corporate Office MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259 800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244 Fax: 310-943-2238
mexico United Kingdom
MQ Cipsa Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Unit 2, Northpoint Industrial Estate,
Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected].uk
Tel: 0161 339 2223
Fax: 0161 339 3226
Canada
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2012, MULTIQUIP INC.
Multiquip Inc
and
the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property
of their respective owners and used with permission.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this document are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
UWKB
Wheel Kit Installation
Other MULTIQUIP Accessories manuals
