MrCool 16117100003415 Operating instructions
Hyper Heat
Wired Thermostat
MODEL:
16117100003415
Read this manual carefully before installation and keep it where
the operator can easily nd it for future reference.
Due to updates and constantly improving performance, the
information and instructions within this manual are subject to
change without notice.
Version Date: 02/22/24
Please visit www.mrcool.com/documentation
to ensure you have the latest version of this manual.
Installation
& Owner’s
Manual
mrcool.com1
CONTENTS
SAFETY PRECAUTIONS .....................................................................................................................2
PACKING LIST ....................................................................................................................................3
PRODUCT OVERVIEW .......................................................................................................................4
3.1 Dimensions .........................................................................................................................4
3.2 Technical Requirements ..................................................................................................4
3.3 Specications .....................................................................................................................4
3.4 Features & Functions .........................................................................................................4
3.5 LCD Display .........................................................................................................................5
3.6 Controller Buttons .............................................................................................................6
INSTALLATION ..................................................................................................................................7
OPERATION .....................................................................................................................................11
5.1 Set Day & Time .................................................................................................................11
5.2 Start/Stop Operation ......................................................................................................11
5.3 8° Heating Function .........................................................................................................11
5.4 Set Operation Mode ........................................................................................................12
5.5 Set Room Temperature ....................................................................................................12
5.6 Set Fan Speed ....................................................................................................................12
5.7 Set Keypad Tone ...............................................................................................................13
5.8 Set Child Lock Function ....................................................................................................13
5.9 Set Turbo Function ...........................................................................................................13
5.10 Set PTC Function .............................................................................................................13
5.11 Set Follow Me Function ..................................................................................................13
5.12 Intelligent Eye Display ....................................................................................................14
5.13 Filter Reset Function ......................................................................................................14
5.14 Humidity Setting Function .............................................................................................15
5.15 GEAR Function .................................................................................................................15
5.16 Set Rotation & Backup Function ...................................................................................15
5.17 Set Timer Functions ........................................................................................................16
5.18 Wireless Control Connection .........................................................................................24
SETTINGS .........................................................................................................................................24
TROUBLESHOOTING ......................................................................................................................26
1
Contents
IMPORTANT INSTALLATION INFORMATION!
• Read this manual carefully before installing and operating the wired thermostat. Retain this manual for
future reference.
• This manual provides detailed descriptions of the precautions that you should be aware of during operation.
• In order to ensure accurate servicing and repair, read this manual carefully before performing maintenance.
• All of the illustrations in this manual are for explanatory purposes only. There may be slight dierences
between the illustration and the purchased thermostat.
2
3
4
5
6
7
mrcool.com 22
SAFETY PRECAUTIONS
1
Incorrect usage may cause serious damage or injury.
Read Before Using
WARNINGS FOR PRODUCT INSTALLATION
INSTALLATION MUST BE PERFORMED BY AN AUTHORIZED DEALER OR SPECIALIST. DEFECTIVE
INSTALLATION CAN CAUSE WATER LEAKAGE, ELECTRICAL SHOCK, OR FIRE.
1. Follow all steps detailed in this manual.
2. Improper installation could lead to electric shock or re.
3. Moving and re-installation must be performed by professionals. Failing to do so may lead to abnormal
operation or re.
4. Do not install the unit in a place that is vulnerable to ammable gas leakage. Leakage of ammable gas
could lead to re.
5. Do not install in a location with oil, vapor, or sulfured gas, as the unit can become deformed, leading to
system malfunction.
6. Do not operate the thermostat with wet hands or let water enter the thermostat. Otherwise, electric shock
could occur.
7. Ensure the wiring corresponds with the thermostat's current requirements. Failing to do so could cause
electrical leakage and re.
8. For wiring, use only the cables specied. Do not subject the terminal to external force. This could lead to
the wire becoming damaged and result in re.
9. Refer to the wiring diagram included in this manual to connect the wired controller to the indoor unit.
10. The wired controller works in a low voltage loop circuit. DO NOT directly connect the cable to high voltage
(115V, 220V). Keep a clearance between the ex or rigid conduit at 12-20 inches (300-500mm) or above.
11. The shielded cable of the wired controller must be rmly grounded.
12. DO NOT use an insulation resistance tester.
BATTERY WARNINGS-KEEP OUT OF REACH OF CHILDREN
INGESTION HAZARD: Contains button cell or coin battery.
• If the battery compartment does not close securely, stop using the product and keep it away from children.
• If batteries may have been swallowed or placed inside any part of the body, seek immediate medical
attention.
• Swallowing can lead to chemical burns, perforation of soft tissue, and death. Severe burns can occur within
2 hours of ingestion. Seek medical attention immediately.
• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away
from children. DO NOT dispose of batteries in household trash or incinerate. Even used batteries can cause
severe injury or death.
• Non-rechargeable batteries are not to be recharged.
• Call a local poison control center for treatment information.
• Do not force discharge, recharge, disassemble, heat above the manufacturer's specied temperature
rating, or incinerate. Doing so may result in chemical burn injuries due to venting, leakage, or explosion.
• Ensure the batteries are installed correctly according to polarity (+ and -).
• Do not mix old and new batteries or dierent brands of types of batteries, such as alkaline, carbon-zinc, or
rechargeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period
of time according to local regulations.
• Battery type: CR2032
• Battery Power Supply: 3.0V
1-Safety Precautions
mrcool.com3
PACKING LIST
2
2-Packing List
The listing below shows the accessories and parts (these may vary depending on purchase & options).
Use all of the installation parts and accessories to install the system. Improper installation may result in
water leakage, electrical shock, re, and/or equipment failure.
PART LOOKS LIKE QUANTITY
Wired Controller 1
Installation & Owner's Manual 1
Screws
6
(Three M3.9*25-Wall Mount)
(Two M4x25-Switch Box Mount)
(One M4x8-Connective Wire Group Mount)
Wall Plugs 3
(For wall-mounting)
Plastic Screw Bars 2
(For attaching to switch box)
Battery 1
To Be Prepared by Installer:
1. Switch Box
3.2 x 3.2 inches (82 x 82 mm)
2. Wiring Tube
Insulating Sleeve and Tightening Screw
mrcool.com 4
4
PRODUCT OVERVIEW
3
3.1 Dimensions
3.3 Specications
Wiring Type Size Total Length
Shielded
Cable
0.5mm2<66 ft (20m)
0.75-1.25mm2<164 ft (50m)
Input Voltage DC 12V
Ambient Temperature 32~110°F (0~43°C)
Ambient Humidity RH40%~RH90%
3.4 Features & Functions
Features:
• LCD Display
• Error Code
Display
• 4-Way Wire
Layout
Design
• Room
Temperature
Display
• Weekly Timer
Functions:
• Modes: Auto, Cool, Dry, Heat, Fan
• Fan Speeds: Auto/Low/Med/High speed
• Timer ON/OFF
• Temperature Setting
• Follow Me
• Turbo
• 24-Hour System
• 12-Hour System
• Sleep
• 8 Degree Heating Function
• Auto Restart
• Automatic Airow Test
• Rotation & Backup
• Dual Control
• Group Control
• Child Lock
• Clock
3.2 Technical Requirements
EMC and EMI comply with CE certication requirements.
Note: A connective wire of 19.68 feet (6 meters) is recommended.
mrcool.com5
PRODUCT OVERVIEW
3
3.5 LCD Display
mrcool.com 6
6
3.6 Controller Buttons
1. FAN SPEED button
2. MODE button
3. FUNC. button
4. SWING button
5. ADJUST button
6. TIMER button
7. COPY button
8. POWER button
9. CONFIRM button
10. BACK button
11. DAY OFF/DELAY button
12. CHILD LOCK button
PRODUCT OVERVIEW
3
mrcool.com7
INSTALLATION
4
4-Unit Installation
Step 1: Remove the upper section of unit
Insert a at head screwdriver into the slots
located at the bottom of the wired controller (2
places). Remove the front cover. (See g. 4-1)
NOTE: Do not pry up and down, only rotate
the screwdriver.
NOTE
The Printed Circuit Board (PCB) is mounted in the upper part of the wired controller. Use care not to
damage the board with the at head screwdriver.
Step 2: Attach Back Plate
For exposed mounting, fasten the back plate to the wall with 3 ST3.9*24 screws and plugs. (See g. 4-2)
Use 2 M4X25 screws to install the back cover of the 86 switch box, and use 1 ST3.9*25 screw to attach
to the wall.
NOTE
Attach to a at surface. Be careful not to distort the back plate of the wire controller by over-
tightening the mounting screws.
mrcool.com 8
8
INSTALLATION
4
Step 3: Battery Installation
• Put the battery into the battery compartment, ensuring the positive
side of the battery is in accordance with the positive side of the
compartment.
• Set the correct time during the rst operation.
• Batteries in the wired controller can keep time after a power failure.
When power is restored, the time display should still remain correct.
If it is incorrect, replace the battery and reset the time.
Step 4: Indoor Unit Wiring
• Using pliers or a similar tool, notch the section for the wiring to pass through.
• Connect the terminals on the remote controller (HA, HB), and the terminals of the indoor unit (HA,
HB). (HA and HB do not have polarity. See Fig. 4-5.)
NOTE
• DO NOT allow water to enter the wired controller. Use the trap and putty to seal the wires.
• The connecting wires must be xed and cannot be pulled.
NOTE
Put on a at surface. Be careful not to distort the back plate of the
controller by over-tightening the mounting screws.
mrcool.com9
INSTALLATION
4
The main/secondary wired controller can be used to enable two wired controllers to control one
unit. The wired controllers connect to the unit's HA and HB ports through the HA and HB port on the
controller. There is no polarity between HA and HB. See Fig. 4-7.
For some units, the wired controller connects to the unit HA and HB ports through the HA and HB
ports. There is no polarity between HA and HB. See Figure 4-6.
NOTE
Wired controller with wireless
function does not have this
function.
Table of contents
Other MrCool Thermostat manuals
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Honeywell
Honeywell CM721 user manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
