Mr Safe WB-20 Installation instructions
Video Doorbell
FULL MANUAL
GB – NL
1. Packaging content
A. Video doorbell unit
B. Mounting wrench
C. Mounting bracket
D. Hex screw
E. Screw plugs
F. Screws
G. Extra doorbell
2. Parts & Buttons
FRONT
1. Microphone
2. Night Sensor
3. Camera
4. PIR Motion Sensor
5. LED indicator
6. Touch button
7. Speaker
BACK
A: Support Fastener
B: Reset button
C: NO (normally opened)
D: GND (Ground)
E: NC (normally closed)
F: AC/DC connector
G: AC/DC connector
H: Product Label
I: Micro SD
H
GB
Note: Reset & setup button: Press the reset button and hold for at least 5 seconds to add the
device
MOUNTING BRACKET
A: Hole for screw
B: Hole for cable
C: Hole for fastener
3. Installation instructions
NOTE: Before step 6, please read chapter 4, 5 and 6 to connect firstly to the wi-fi correct.
1. Take the Video doorbell out of the packaging and make sure that all the components
described in the packaging content are present.
2. (optional) Insert an SD/TF card into the Micro SD cardslot.
Note: Make sure the device is turned OFF when you insert an SD/TF card into the slot.
SD/TF cards with capacity up to 64GB are supported.
3. Fix the mounting bracket to the desired place on the wall or door. Start by holding the
bracket against the wall and mark with a pencil the place where to drill the holes. Drill the
holes and insert the Screw plugs. When the screw plugs are in place, hold the bracket
again against the wall and use the screws to attach it to the wall.
4. Connect the power wires, for AC/DC power, use the bottom 2 screws (as described on this
scheme) AC/DC: AC 8-16V or DC 9-24V with no specific + or - pin
Optionally, if you have a smart lock; you can connect it here also:
There are 2 kinds of electric door locks; Normally Open (NO) or Normally Closed (NC). If you
don’t know what type of lock you have, consult the manual of your lock, but usually it’s
Normally Open (NO). Connect the adapter of the door lock to the power (230V), connect 1
wire through the NO and GND connection and the other wire from the adapter to the electric
lock directly.
(NO+GND): to NO Lock
(NC+GND): to NC Lock
5. Slide the device in the bracket.
PLEASE READ AND EXECUTE CHAPTERS 4, 5 and 6 before continuing the installation
6. Use the mounting wrench and the 2 HEX screws to finish attaching the video doorbell onto
the bracket.
4. Download the MrSafeBell app in the Apple app store or on Google play store.
5. Register the user account
1. Open the app and grant the app access to the app to record video, save pictures, record
sound and the location.
2. Cick the “Register new user” button.
3. Check the disclaimer and accept when OK for you.
4. Enter a new user name (no less than 5 characters) and a password (no less than 6
characters).
Note: if you have forgotten your login details, enter your email address to reset the password.
6. Setup the device
Click on the “+” button to setup the device and then click “Setup Device”
The setup wizard will now tell you to connect the power to the doorbell (as described in
chapter 3); turn ON the doorbell and press “NEXT”, wait for the start up tone and the ‘calling
button’to be visible and press “GOT IT”.
You will now hear a Di-Di-Di-sound. Press “YES” in the app.
Note: If you do NOT hear the Di-Di-Di-sound; press “NO” and execute the following step:
Press the reset button (B) on the back of the doorbell for about 5 seconds until you hear a
tone. The device will restart and after about 30 seconds you will hear the startup tone again
and Di-Di-Di. Press “YES” on the screen to confirm that you hear this tone.
Click “Start” after the ‘calling button’ indicator is on and the Di-Di-Di-sound is heard from the
device. Go to the wi-fi settings of your smartphone and select the wi-fi network “Bell-*****”.
The password is bell@Door
Click OK and exit.
Open the MrSafeBell app and click on the connected device. You can now give it a
dedicated name (such as front door, back door, office,…).
Please note that you are the first user to add the device, meaning that you are the
administrator. This means that you can share the device with other users or delete
the users of this bell.
Click the settings icon and the Wi-Fi icon to connect the device to the Wi-Fi. Select the Wi-fi
network and enter the password to link your doorbell to your proper network.
The device will now be online and show its videofeed to you.
If this is not the case, slide down to refresh;
7. Granting a family member access to the video doorbell
You can have multiple members of your family connected to the doorbell. To connect
someone, start by downloading the MrSafeBell app on the member’s smartphone. The new
member has to register his user name, password and e-mail address.
The administrator has to add this new user name, and then the new user can scan the QR code
generated by the administrators app.
8. Changing the settings of your linked doorbell
Press the settings icon of your linked doorbell and change the following parameters:
-Doorbell name
-System settings: here you can change the waiting duration of the call that the doorbell
makes and you can reboot the doorbell from a distance here.
-Member management: see which members of your family have access to this doorbell /
video feed
-Motion detection: Turn the motion detection on or off and specify the sensitivity of the
motion detection.
-Lock settings: here you can setup the automated unlocking if you have a Smart Lock on
your door.
-Equipment time settings: here you can set the time and date of your doorbell, or sync it
up to your smartphone.
-Push settings: here you can change whether you wish to receive push notifications on
your smartphone
-Wifi settings: check the connectivity of your doorbell here
-SDCard settings: change the settings of your recording to SD Card here, or format it from
a distance.
-Firmware update: Here you can check if you have the latest firmware version of the
doorbell firmware.
Table of contents
Languages:
Other Mr Safe Accessories manuals
