MODI T10 Series User manual
MODI-T10
Multifunctional Bluetooth Helmet Intercom
T10-3/T10-4
Table of Contents
Packet Contents -------------------Page 1
Introduction ------------------------- Page 2
Install Instructions ----------------- Page 3
Led State ----------------------------- Page 6
Pair to Cell Phone ------------------ Page 8
Pair to Common BT Headset----- Page 10
Internal Intercom -------------------Page 11
FM Operation ----------------------- Page 17
Technical Specifications ----------- Page 18
Certification ------------------------- Page 19
1
Packet Contents
T10 Main Unit:
HIFI Speaker and Microphone
USB Cable
Clip Mounting Bracket
User Manual
2
T10_3/T10_4 Introduction
Power on / Power off Button
1: Power on/Power off
2: Pair mobile phone
3: Power prompt
4: Hang up Bluetooth intercom
5: Music play / pause
6: Call answering /
Third party call answer /End / Reject
Bluetooth Intercom Button
1: Pair Bluetooth intercom
2: Open / exit Bluetooth intercom
Volume + Button
1:Volume +
2:Last song
3:FM turn up
4:Last number redial
Volume - Button
1:Volume -
2: Next song
3
3: FM turn down
4: FM Turn on / Turn off
5:Voice dialing
Fixed installation method
1:Locate the helmet at the left and clean it up
2:Peel off the 3M rubber protective film
3:Apply pressure to the metal carrier to secure the
holder firmly
Note: it takes 24 hours after drying.
Temporary installation method
1:Clip on the left edge of the helmet
2:Remove metal handle after installation
3:If required, use additional anti slip rubber
patches
4
5
Install host
1:Slide T10 host off the top of the clip and you'll
hear a click when it is completely plugged in
2:Plug in the 3.5mm headset plug
Headset mounting method
1:Stick the left and right horns of the headphones
in the position of the left and right ears of the
helmet
2: Keep the microphone in front of the mouth，
Note: microphone holes point to the mouth
6
Led State
Blue light slow flash once：
Bluetooth connection is not connected
Red and blue light flash slowly alternately:
Bluetooth in paired mode
Blue light flash quickly：
Bluetooth in searching situation and pairing mode
Red and blue light flash quickly twice
simultaneously：
Bluetooth intercom status
Red and blue light flash slowly twice
simultaneously：
Bluetooth bridge intercom status
Blue lights flash continuously twice：
Bluetooth connected
Red light flash: Charging
Blue light on: Charge complete
Low battery warning: Red light quickly flash
three times
7
Charging
1. You can charge with the Micro USB cable in
the package. During charging, red light is flash,
After full charging, the light will turn blue. and it
is recommended to recharge the battery before
each use. Suggest full charge before each use.
2. Low battery warning：Headset will
automatically voice prompt low battery at every 5
minutes, meanwhile the red light flashes quickly
3. times to prompt the user to recharge it
3. Battery state notify: When standby, double
press K_POWER to report battery level.
Power on /Power off
1. Press K_POWER for approx. 2S, blue light
flashing, and power on.
2. When power on status, press K_POWER for
approx. 2s, red light flashing, power off.
8
Pairing with cell phone and using
Mobile pairing steps
1. When power off，press K_POWER for
approx 8S, red and blue light flash alternately，
headset prompt “pairing”. Open the phone
Bluetooth, search for ‘T10-3’or ‘T10-4’, then
click on the phone connection pair. After the
pairing, the phone light goes back to standby
mode, and the blue light flashes 2 times.
Answer phone calling dialing method
Answer phone calling: When there is call, press
K_POWER to answer.
Automatically answer phone calling: When
there is call, headset will automatically answer
after 12s if haven’t pressed K_POWER to
answer.
End phone calling: during talking, short press
K_POWER to end the call。
Reject phone calling: When have incoming calls,
long press K_POWER about 2s to reject
This manual suits for next models
2
Table of contents
Other MODI Headset manuals
