Minebea Intec Puro User manual
PRESENTED BY
JPBOWLIN.COM
817.332.8116
J.P. Bowlin is a quality-driven Calibration Company
that has provided calibration, repair and sales
of all types of weighing and measurement products since 1931.
Weight indicator Puro®
Operating Instructions
98628-000-62 Edition 1.0.1 6/22/2020
Minebea Intec Bovenden GmbH & Co. KG, Leinetal 2, 37120 Bovenden, Germany
Phone: +49.551.309.83.0 Fax: +49.551.309.83.190
Foreword
Must be followed!
Any information in this document is subject to change without notice and does not represent a commitment on
the part of Minebea Intec unless legally prescribed. This product should only be operated/installed by trained
and qualied personnel. In correspondence concerning this product, the type, name, and release number/serial
number as well as all license numbers relating to the product have to be cited.
Note
This document is partially protected by copyright. It may not be changed or copied, and it may not be used
without purchasing or written permission from the copyright owner (Minebea Intec). The use of this product
constitutes acceptance by you of the abovementioned provisions.
Table of contents
1 Introduction......................................................................................................................................... 3
1.1 Read the manual.........................................................................................................................................................3
1.2 This is what operating instructions look like..........................................................................................................3
1.3 This is what lists look like...........................................................................................................................................3
1.4 This is what menu items and softkeys look like.....................................................................................................3
1.5 This is what the safety instructions look like.......................................................................................................... 3
2 Safety instructions...............................................................................................................................5
2.1 General information...................................................................................................................................................5
2.2 Incoming goods inspection.......................................................................................................................................5
2.3 Before operational startup........................................................................................................................................5
2.3.1 Danger of explosion ........................................................................................................................................5
2.3.2 IP protection.....................................................................................................................................................5
2.3.3 Storage and transport conditions .................................................................................................................5
2.4 Failure and excessive stresses..................................................................................................................................6
3 Device installation................................................................................................................................ 7
3.1 Mechanical preparation............................................................................................................................................. 7
3.1.1 Ambient conditions ......................................................................................................................................... 7
3.1.2 Installation location......................................................................................................................................... 7
3.1.3 Unpacking......................................................................................................................................................... 7
3.1.4 Checking the equipment supplied................................................................................................................ 7
3.1.5 Indicator holder................................................................................................................................................ 7
3.2 Connections.................................................................................................................................................................8
3.2.1 Electrical supply ...............................................................................................................................................8
3.2.2 Connecting the platform.................................................................................................................................9
3.2.3 Connecting a printer...................................................................................................................................... 10
4 Device description ..............................................................................................................................11
4.1 Display and operating elements .............................................................................................................................11
4.1.1 Overview........................................................................................................................................................... 11
4.1.2 Display elements............................................................................................................................................. 11
4.1.3 Operating elements........................................................................................................................................12
5 Operating .......................................................................................................................................... 14
5.1 Basic functions.......................................................................................................................................................... 14
5.1.1 Switching on the device................................................................................................................................ 14
5.1.2 Switching o the device................................................................................................................................ 14
5.1.3 Adjusting the GEO setting............................................................................................................................ 14
5.1.4 Increment d..................................................................................................................................................... 14
5.1.5 Select application program .......................................................................................................................... 14
Weight indicator Puro® Table of contents
Minebea Intec EN-1
5.2 Application programs ...............................................................................................................................................15
5.2.1 Weighing application .....................................................................................................................................15
5.2.2 Counting application......................................................................................................................................17
5.2.3 Checking application.....................................................................................................................................20
5.2.4 Totalizing application and statistics mode................................................................................................28
5.3 Menu...........................................................................................................................................................................32
5.3.1 Accessing the menu.......................................................................................................................................33
5.3.2 Menu navigation............................................................................................................................................34
5.4 Calibration and adjustment.................................................................................................................................... 41
5.4.1 [ADC.CON] conguring A/D converter....................................................................................................... 41
5.4.2 [CAL] calibration.............................................................................................................................................44
5.4.3 [LIN] linearization ..........................................................................................................................................47
5.4.4 [GEO] geographic data (calibration location)............................................................................................50
5.4.5 GEO code table................................................................................................................................................51
5.5 SBI interface ..............................................................................................................................................................53
6 Maintenance/repairs/cleaning...........................................................................................................56
6.1 Repairs........................................................................................................................................................................56
6.2 Cleaning .....................................................................................................................................................................56
6.2.1 Instructions for cleaning...............................................................................................................................56
6.2.2 Cleaning agents..............................................................................................................................................56
7 Waste disposal policy......................................................................................................................... 57
8 Error correction .................................................................................................................................58
8.1 Service information..................................................................................................................................................59
9 Technical data....................................................................................................................................60
9.1 Specication..............................................................................................................................................................60
9.2 Accessories ................................................................................................................................................................ 61
9.3 Dimensions................................................................................................................................................................ 61
10 Appendix ...........................................................................................................................................64
10.1 Printouts ....................................................................................................................................................................64
10.2 FCC notice..................................................................................................................................................................65
Weight indicator Puro® Table of contents
EN-2 Minebea Intec
1 Introduction
1.1 Read the manual
-Please read this manual carefully and completely before using the product.
-This manual is part of the product. Keep it in a safe and easily accessible location.
1.2 This is what operating instructions look like
1. - n. are placed before steps that must be done in sequence.
1.3 This is what lists look like
-indicates an item in a list.
1.4 This is what menu items and softkeys look like
[ ] frame menu items and softkeys.
Example:
[Start]- [Applications]- [Excel]
1.5 This is what the safety instructions look like
Signal words indicate the severity of the danger involved when measures for preventing
hazards are not followed.
DANGER
Warning of personal injury
DANGER indicates death or severe, irreversible personal injury which will occur if the
corresponding safety measures are not observed.
Take the corresponding safety precautions.
WARNING
Warning of hazardous area and/or personal injury
WARNING indicates that death or severe, irreversible injury may occur if appropriate
safety measures are not observed.
Take the corresponding safety precautions.
CAUTION
Warning of personal injury.
CAUTION indicates that minor, reversible injury may occur if appropriate safety
measures are not observed.
Take the corresponding safety precautions.
is placed before a step.
describes the result of a step.
1 Introduction Weight indicator Puro®
Minebea Intec EN-3
NOTICE
Warning of damage to property and/or the environment.
NOTICE indicates that damage to property and/or the environment may occur if
appropriate safety measures are not observed.
Take the corresponding safety precautions.
Note:
User tips, useful information, and notes.
Weight indicator Puro® 1 Introduction
EN-4 Minebea Intec
2 Safety instructions
2.1 General information
-The device may only be used as intended for weighing tasks.
-Observe the operating limits of the device.
-The voltage rating printed on the power supply (see type plate) must be the same as
the local line voltage.
-Before connecting or disconnecting electronic peripheral devices, disconnect the
device from the mains or from the data interface.
-Unplug the power cord from the mains supply before cleaning.
-Unplug the power cord from the mains supply before maintenance; only establish
internal connections when disconnected from the power supply.
-Make sure that no liquid enters the device.
2.2 Incoming goods inspection
Check the contents of the consignment for integrity. Check the contents visually to
determine whether any damage has occurred during transport. If there are grounds for
rejection of the goods, a claim must be led with the carrier immediately. A Minebea Intec
sales or service organization must also be notied. Visit our website
http://www.puroscales.com or contact your dealer.
2.3 Before operational startup
NOTICE
Perform visual inspection.
Before operational startup as well as after storage or transport, inspect the product
visually for signs of mechanical damage.
The product should not be put into operation if it displays signs of visible damage
and/or is defective.
2.3.1 Danger of explosion
Do not use the device in hazardous areas.
2.3.2 IP protection
The indicator fullls protection grade IP43.
2.3.3 Storage and transport conditions
NOTICE
Material damage is possible.
Unpacked devices may lose their precision due to strong vibrations; strong vibrations
may impair the safety of the device.
Do not subject the device to extreme temperatures, moisture, shocks, and
vibrations.
2 Safety instructions Weight indicator Puro®
Minebea Intec EN-5
2.4 Failure and excessive stresses
If the device or the power cord display visible damage: Disconnect the power supply and
secure the device to prevent it being used further.
Do not unnecessarily subject the device to extreme temperatures, corrosive chemical
vapors, moisture, shocks, and vibrations.
Extreme electromagnetic inuences can aect the display value. Once the disturbance
has ceased, the product can be used again as intended.
Weight indicator Puro® 2 Safety instructions
EN-6 Minebea Intec
3 Device installation
3.1 Mechanical preparation
3.1.1 Ambient conditions
-Only use within buildings.
-Operating temperature: -10°C to +40°C
-Storage temperature: -20°C to +50°C
-Relative humidity: 20% to 85%, non-condensing
-Altitude: up to 3,575 m
3.1.2 Installation location
-Place the device on a stable, at surface.
-Position the device so that the power plug is freely accessible and the power cord
does not present an obstacle or trip hazard.
Avoid unsuitable inuences at the installation location:
-Extreme temperatures and excessive temperature uctuations
-Heat due to proximity to heaters or due to direct sunlight
-Aggressive chemical vapors
-Extreme moisture
-Extreme vibrations
3.1.3 Unpacking
3.1.4 Checking the equipment supplied
-1 indicator
-1 USB power supply with cable
-1 indicator holder
-Safety instructions and QR code for access to the complete documentation
3.1.5 Indicator holder
Align the holder using the threaded holes on the side of the indicator and install the
knobs. Set the indicator at the desired angle and tighten the knobs.
. Unpack the device and check it for visible external damage.
If there is damage, follow the instructions in the chapter "Safety check".
. Keep the original packaging in case the device needs to be returned. Remove all
cables before sending.
3 Device installation Weight indicator Puro®
Minebea Intec EN-7
Other manuals for Puro
2
This manual suits for next models
2
Table of contents
Other Minebea Intec Accessories manuals
Minebea Intec
Minebea Intec Puro EF-IN P User manual
Minebea Intec
Minebea Intec MP30 User manual
Minebea Intec
Minebea Intec Mini FLEXLOCK PR 6143/00N+S User manual
Minebea Intec
Minebea Intec Puro EF-LLP1500-3d User manual
Minebea Intec
Minebea Intec Pendeo PR 6204 Series User manual
Minebea Intec
Minebea Intec Mini FLEX User manual
Minebea Intec
Minebea Intec Maxxis 5 Count PR 5900/82 User manual
Minebea Intec
Minebea Intec Combics 3 Filling Basic H3 User manual
Minebea Intec
Minebea Intec PR 6221/12.5 t User manual
Minebea Intec
Minebea Intec PR 6211 User manual
