mimsafe 45-90 CORNER KIT User manual
www.mimsafe.se
45°-90° CORNER KIT
ASSEMBLY INSTRUCTIONS
USING 2X GATE & WALL KIT 00324
UNIVERSAL SAFETY
1986
SINCE
IMPACT TECHNOLOGY
APPROVED
INFORMATION ABOUT THE 45°-90° CORNER KIT
The 45°-90° Corner Kit has been designed
and developed specically to greatly
reduce the risk of rotational falls.
The most important element of this
kit is that it will not break the fence or
risk injury to the horse if hit vertically.
The rail is only released when impacted
horizontally by the horse. The risk of a
resulting rotational fall is thus reduced.
It is essential to follow the recommended dimensions on the fence for the
correct function. If the recommended procedure is not correctly followed it
may cause the failure of the device.
For your own safety and that of others please note the following step by step
advice for correct preparation and installation. It is important that you follow your
own health and safety requirements when constructing this kit.
WARNING!
Ensure that you have all parts of the 45°-90° Corner Kit.
Be aware of the risk of injury when handling heavy rails,
poles and the tools for mounting.
RECOMMENDED FENCE DIMENSIONS
MIN-MAX SIZE
SIZE
A:
B:
inch
6 – 10
mm
150 - 250
Check
MIN-MAX DIAMETER
inch
8 – 10
mm
200 - 250
MIN-MAX WEIGHT
lb
88 - 330
kg
40 - 150
MAXIMUM LENGTH
12
cm
ft
350
POST RAIL
4
STEP
A B
Jumping
direction
4X
4X 4X 2X4X4X4X
POST TOP
SECTION
M-TS10X90 POST BOTTOM
SECTION
RAILM-MM12NyM-BR12x22x2sM-SM12x90
not included not included not included
Jumping direction
CF70A
Part no 4XDF18C
Part no 12X
AF76D
Part no 4XBF76C
Part no 4X
Minimum-Maximum
45°-90°
IMPORTANT
The clips F18C must be placed
on these posts exactly.
1
STEP
2
STEP
2X2X2X
M-MM12NyM-BR12x22x2sM-SM12x120
4X
2X TOP
BOTTOM
B
A
B
A
IMPORTANT
When mounting, make sure
the hinge is mounted as shown
in picture to ensure correct
activation.
14X
not included
16 inch/40 cm
IMPORTANT
Make sure you follow
the cutting measurements
for correct fence
release/function
2X
2X
3
STEP
4
STEP
IMPORTANT
Make sure you follow
the mounting
measurements for correct
fence release/function
C
IMPORTANT
Make sure the horizontal rail
is rigid xed to the posts.
12X
not included
8X
not included
Vertical
line
Center
aligned
Side
aligned
9-10 inch
22-25 cm
9-10 inch
22-25 cm
6
STEP
5
STEP
2X
M-TS10X90
D
2X
2X Distance between brackets
should be adjusted to avoid
clip D rattling.
IMPORTANT
Vertical
line
7
STEP
Make sure it’s clearance
during activation
IMPORTANT
Fill out the gap with a xed lower post and
a loose stub above to avoid “foot trap”.
IMPORTANT
Connect the stub
with 3.6 mm
zip ties
IMPORTANT
www.mimsafe.se
200 mm
8 inch
50 mm
2 inch
2x Gate & Wall Kit - 00324 Edition 2019-03
The advantages of the 45°-90° Corner Kit
1. It has been produced with safety being the
rst and foremost important factor.
2. Reduces the possibility of rotational falls.
3. FEI approved number FEIXXXSWE.
4. Controlled movement of fence during release.
5. Reconstruction time is less than 30 seconds.
6. The parts are made of powder coated steel and
can be left outside, no maintenance is required.
7. The very highest quality of product from
Sweden ISO 9001.
The Mim clip (F18C) breaks on impact, which clearly indicates when replacement is
needed. The top section is connected to the post with an hinge that makes the fence
easy to reconstruct. This saves time, guarantees fair and correct judging for riders
and contributes to the overall safety of the sport.
IMPORTANT
When top section is released the gap between top section and bottom section
should be maximum 50 mm.
If gap is wider, then place object to shrink/reduce the gap.
When top section is released the distance between top section and ground
should be minimum 200 mm.
If distance between ground and top section is less, then place an object which
will prevent the top section falling into the SAFE AREA
This manual suits for next models
1
Other mimsafe Automobile Accessories manuals
