Milnor Mark II User manual

Published Manual Number/ECN: MAUPQOPRAU/95093N

• Publishing System: TPAS

• Access date: 06/13/2000

• Document ECN's: Latest Available

CE—

OPERATION - Mark II, Q-Style

Washer-Extractor

FONCTIONNEMENT - Mark II,

Q-Style Laveuse-essoreuse

BETRIEB - Mark II, Wasch-

Schleuder-Maschine Typ Q

WERKING - Mark II, Q-type

Centrifugerende Wasmachine

FUNZIONAMENTO - Mark II,

Linea-Q Lavacentrifuga

PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

Please Read

About the Manual Identifying Information on the Cover

The front cover displays pertinent identifying information for this manual. Most important, are

the published manual number (part number) /ECN (date code). Generally, when a replacement

manual is furnished, it will have the same published manual number, but the latest available

ECN. This provides the user with the latest information applicable to his machine. Similarly all

documents comprising the manual will be the latest available as of the date the manual was

printed, even though older ECN dates for those documents may be listed in the table of

contents.

When communicating with the Milnor factory regarding this manual, please also provide the

other identifying information shown on the cover, including the publishing system, access date,

and whether the document ECN’s are the latest available or exact.

References to Yellow Troubleshooting Pages

This manual may contain references to “yellow pages.” Although the pages containing

troubleshooting procedures are no longer printed on yellow paper, troubleshooting instructions, if

any, will be contained in the easily located “Troubleshooting” chapter or section. See the table of

contents.

Trademarks of Pellerin Milnor Corporation

The following, some of which may be used in this manual, are trademarks of Pellerin Milnor

Corporation:

Ampsaver®CBW®Gear Guardian®Milnet®Staph-Guard®

Autolint®Dye-Extractor®Hands-Off®Milnor®System 4®

Auto-Purge®Dyextractor®Hydro-Cushion®Miltrac System 7®

Autovac E-P Plus®Mildata®Miltron Totaltrol®

Comments and Suggestions

Help us to improve this manual by sending your comments to:

Pellerin Milnor Corporation

Attn: Technical Publications

P. O. Box 400

Kenner, LA 70063-0400

Fax: (504) 469-1849

Table of Contents

for MAUPQOPRAU/95093N

OPERATION - Mark II, Q-Style Washer-Extractor

Page Description Document/ECN

1 Section 1: English

2 Description of Controls - Mark II, Q-Style Washer-Extractor MSOUPQCTAE/9433AV

6 Normal Operation - Mark II, Q-Style Washer Extractor MSOUPQNOAE/9433AV

11 Correcting Errors - Mark II Washer-Extractor MSOUPUTSAE/9436AV

15 Section 2: Français

16 Description des Commandes - Mark II, Q-Style

Laveuse-essoreuse MSOUPQCTAF/9433AV

20 Fonctionnement courant - Mark II, Q-Style Laveuse-

essoreuse MSOUPQNOAF/9433AV

25 Correction des Erreurs - Mark II Laveuse-essoreuse MSOUPUTSAF/9436AV

29 Section 3: Deutsch

30 Beschreibung der Steuerung - Mark II, Q-Style

Washer-Extractor MSOUPQCTAG/9433AV

34 Normalbetrieb - Mark II, Wasch-Schleuder-Maschine

Typ Q MSOUPQNOAG/9433AV

39 Fehlerbehebung - Mark II, Wasch-Schleuder-Maschine MSOUPUTSAG/9436AV

43 Section 4: Nederlands

44 Beschrijving van de Besturing - Mark II, Q-type

Centrifugerende Wasmachine MSOUPQCTAH/9433AV

48 Normale werking - Mark II, Q-type Centrifugerende

Wasmachine MSOUPQNOAH/9433AV

53 Oplossen Storingen - Mark II Centrifugerende

Wasmachine MSOUPUTSAH/9436AV

57 Section 5: Italiano

58 Descrizione dei Controlli - Mark II, Linea-Q Lavacentrifuga MSOUPQCTAI/9433AV

62 Funzionamento Normale - Mark II, Linea-Q Lavacentrifuga MSOUPQNOAI/9433AV

67 Correzione Errori - Mark II Lavacentrifuga MSOUPUTSAI/9436AV

Section 1

English

MSOUPQCTAE/9433AV

Description of Controls—

Mark II, Q-Style Washer-Extractor

m/M Master switch

This switch controls single-phase control circuit power to the machine and the DC power

supply for the microprocessor and its components. Setting this switch to mduring

operation stops the machine.

aOperator Signal

This signal is activated when operator attention is required, as when unloading is required

or certain errors occur. Pressing Acancels the signal.

ASignal Cancel button

This button extinguishes the operator signal (a). If the signal was programmed as part

of a formula, the formula resumes after this button is pressed. If an error caused ato

illuminate, pressing Aafter correcting the error will extinguish the signal. If awas

illuminated when a valid formula was selected, the signal will terminate automatically

when the formula is started or the door is opened.

R/P Run/Program keyswitch

Setting the keyswitch to Rprevents programmed data from being changed and allows

normal machine operation. Setting the keyswitch to Pallows programming machine

operation and certain troubleshooting procedures.

No symbol Emergency Stop button

This large red button in a yellow rectangle may appear in several locations on the machine.

It performs the same function as 0, but locks in the depressed position and must be

turned to release the button and close the circuit before operation can resume.

0Stop button

This button stops the machine immediately by opening the three-wire circuit. Emergency

Stop buttons perform the same function. Pull cords and kick plates, if the machine has

them, also perform the same function.

1Start button

This button starts a cycle or resumes an interrupted cycle if a formula is selected and

certain safety considerations are met.

Pressing 0+1 jogs the cylinder clockwise if a formula is not running.

lDoor Open button

This button retracts the door plunger to unlock the door if the machine is not running.

Pressing 1+l jogs the cylinder clockwise or counter-clockwise as set by J/j.

J/j Jog switch

This switch determines the direction the cylinder will rotate when jogging is commanded.

Holding the switch at Jjogs clockwise; holding the switch at Jjogs counter-clockwise.

Description of Controls—

Mark II, Q-Style Washer-Extractor MSOUPQCTAE/9433AV (2 / 4)

VBalance Sensing Switch

light—Rigid balancing

models

This light flashes repeatedly while

the machine is balancing, and may

flash during extraction. If the

imbalance exceeds the machine’s

ability to balance the load, this light

flashes continuously. Flashing

through most extractions may

indicate inadequate water to the

balancing system or that the

balancing system requires service.

=Balance Excursion

light—Rigid balancing

models

This light is extinguished when the

imbalance exceeds a preset value, indicating that the extract motor is coasting. Up to six

coasts are normal at the beginning of extraction, but the machine should not coast after

two minutes of extraction unless the imbalance exceeds the machine’s ability to

counterbalance the load. In this case the machine will coast through the entire extraction.

Frequent coasting through most extractions may indicate inadequate water supply to the

balancing system or that the balancing system requires service.

X/Y/ZBalance Valve lights—balancing models

These lights show which balancing valves are open. They are extinguished when

balancing is complete, except for intermittent operation as the balancing system

compensates for changes in the imbalance. Lights that stay on through most extractions

may indicate inadequate water supply to the balancing system or that the balancing

system requires service.

Service is required if two or three lights illuminate at the same time, or if all three lights

illuminate in sequence.

Description of Controls—

Mark II, Q-Style Washer-Extractor MSOUPQCTAE/9433AV (3 / 4)

H/W Manual Flush/Spray

switch—machines with

five-compartment supply

injectors

Hold this switch to Hto flush water into

the first compartment of the supply

injector. Hold this switch to Wto use the

spray nozzle to clean the supply injector.

fManifold Flush button

Press this button to flush the chemical

supply manifold with fresh water.

B/dAlternate Drain switch

Set this switch to dto disable all

machine functions and hold the drain

closed. The machine can be powered off

with the drain closed for overnight

soaking. Set to Bto permit normal operation.

_/- Mildata Remote/Local switch—Mildata option

Set this switch to -to have the machine communicate with the Mildata computer. Set

to _to use internal machine formulas.

E/e Ampsaver switch—Ampsaver option

Ecauses the Ampsaver controller to delay extraction when necessary to prevent the

amperage drawn by all machines from exceeding a preset maximum. eprevents the

Ampsaver controller from affecting machine operation.

Description of Controls—

Mark II, Q-Style Washer-Extractor MSOUPQCTAE/9433AV (4 / 4)

MSOUPQNOAE/9433AV

Normal Operation—Mark II,

Q-Style Washer-Extractor

Start the Operating Day.

Be Safe. Comply with all safety instructions in this manual and on this machine.

Verify Switch Positions.

Switch Symbol Selection Switch Setting by Name/Function

R/P R Set the Run/Program keyswitch to run.

Energize Microprocessor Controller. Set the Master switch to on (M). The operator

signal sounds and a series of displays appear.

RUN FORMULA

00 OR OK POWER OFF Machine is ready for a load.

REMOTE FORMULA 0000 Machine is on-line to Mildata and ready for a load. See “Enter Cake Data

If Machine On-Line to Mildata.”

Other manuals for Mark II

Table of contents

Languages:

Other Milnor Washer manuals

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide